UNIVERSAL HARDWARE UH4051 Manuel utilisateur

DOOR CLOSER

MODEL UH4051 or UH4052 INSTALLATION INSTRUCTIONS

BEFORE STARTING THE INSTALLATION, refer to the specication chart below to conrm closer selection.

PREPARATION FOR FASTENERS DETERMINE HAND OF DOOR

COMPONENTS CLOSING SPEED CONTROL

ADJUSTING SWEEP SPEED & LATCHING SPEED ADJUSTING FOOT FOR CLOSING POWER

PAGE 1

PULL SIDE

PUSH SIDE

HINGE SIDE OF DOOR

STOP SIDE OF DOOR

HINGE SIDE OF DOOR

THIS IS A RIGHT HAND DOOR

THIS IS A LEFT HAND DOOR

THIS VALVE CONTROLS

LATCHING SPEED: (SLOWER- TURN CLOCKWISE)

(FASTER - TURN COUNTER CLOCKWISE)

THIS VALVE CONTROLS

SWEEP SPEED: (SLOWER- TURN CLOCKWISE)

(FASTER - TURN COUNTER CLOCKWISE)

ATTENTION:

ADJUST CLOSING SPEED

TIME TO BETWEN 4 & 6

SECONDS FROM 90°. USE OF

THE DOOR BY HANDICAPPED,

ELDERLY OR SMALL

CHILDREN MAY REQURE

LONGER CLOSING TIMES. STANDARD CLOSING CYCLE

CAUTION: DO NOT BACK

VALVES OUT OF CLOSER

OR LEAK WILL RESULT.

TURN SPEED REGULATING VALVE CLOCKWISE TO SLOW DOWN OR COUNTER

CLOCKWISE TO SPEED UP DOOR MOVEMENT.

MOVE FOOT PIVOT TO HOLE AS ILLUSTRATED

LESS POWER MORE POWER

HINGE EDGE OF DOOR

FASTENERS

Model

Type

Closer Size

Maximum Door Width

Maximum Door Weight

Maximum opening angle for closer

UH4051/UH4052

UL 3 Hr Fire Rated

38"

125 lbs

180˚

DOOR OR FRAME RECOMMENDED DRILL SIZES DRILL DEPTH

Machine Screw Hollow Metal or Aluminum #7 (.201") & 1/4"-20 Tap *Through One Side

Sheet Metal Screw

Wood Cored

*1-1/4"

3/16"

1/8"

Hardwood

Hollow Metal

999-30003

LATCH

10°

PARALLEL ARM PLATE

ELBOW WASHER AND SCREW

MAIN ARM

SECONDARY ARM

FOOT

CLOSER BODY

LOCKNUT

PINION CAP

PINION SHAFT

MAIN ARM SCREW

*Measure door thickness before

drilling pilot holes to prevent drilling

through opposite side

REGULAR ARM INSTALLATION

MODEL UH4051 or UH4052 INSTALLATION INSTRUCTIONS

PAGE 2

MODEL DIMENSIONS "A" OPENING

inches [mm]

UH4051

UH4052

7" 178

6" 152

3-1/2" 89

*DOOR/WALL/HARDWARE/JAMB CONDITIONS PERMITTING

TO 100°

101° TO 120°

121° TO 180°*

999-30003

POSITION OF MAIN ARM WHEN ASSEMBLING TO PINION SHAFT

SPEED REGULATING VALVES

90°

FRAME

DOOR

FOOT

SCREW

& WASHER

PINION

CAP

6" (152 mm)

A1 3/4" (44.5 mm)

1" (25 mm)

9-1/16" (230 mm)

1" (25 mm)

3/4" (19 mm)

1. SELECT DEGREE OF OPENING. USE DIMENSIONS SHOWN IN CHART AND ILLUSTRA-

TIONS ABOVE TO MARK LOCATION OF ATTACHING SCREWS ON THE DOOR AND FRAME.

PREPARE HOLES (See Preparation For Fasteners chart, Page 1).

2. ATTACH CLOSER TO THE DOOR WITH THE SPEED REGULATING

VALVES FACING THE HINGE SIDE OF DOOR.

DISASSEMBLE FOREARM FROM MAIN ARM BY REMOVING ELBOW WASHERS AND SCREW.

4. ASSEMBLE MAIN ARM TO CLOSER USING MAIN ARM SCREW AND LARGE FLAT WASHER.

5. ATTACH THE FOOT OF THE FOREARM TO THE FRAME.

6. ADJUST THE LENGTH OF THE FOREARM TO POSITION THE FOREARM AT A RIGHT

ANGLE TO THE FRAME TO ENSURE PROPER LATCHING, AND ATTACH FOREARM TO

MAIN ARM USING ELBOW WASHERS AND SCREW.

7. SNAP PINION CAP OVER THE PINION AT THE BOTTOM OF THE CLOSER.

8. ADJUST CLOSER (refer to ADJUSTING SWEEP SPEED & LATCHING SPEED on page 1)

• RIGHT HAND DOOR ILLUSTRATED. SAME

DIMENSIONS APPLY TO LEFT HAND DOOR

• MEASURED FROM HINGE CENTERLINE

• DO NOT SCALE DRAWING

FRAME

RIGHT HAND DOOR

RIGHT ANGLE

POSITION OF MAIN ARM

WHEN ASSEMBLING TO SPINDLE

INSTALLATION INSTRUCTIONS

RIGHT HAND DOOR

LEFT HAND DOOR

PAGE 3

TOP JAMB INSTALLATION

MODEL UH4051 or UH4052 INSTALLATION INSTRUCTIONS

MODEL DIMENSIONS "A" OPENING

inches [mm]

UH4051

UH4052

7" 178

6" 152

3-1/2" 89

*DOOR/WALL/HARDWARE/JAMB CONDITIONS PERMITTING

TO 100°

101° TO 120°

121° TO 180°*

999-30003

3-1/8" (80 mm)

MAXIMUM

RIGHT HAND DOOR- RH

LEFT HAND DOOR-LH

CENTERLINE

OF HINGE

DOOR

FOOT

9-1/16" (230 mm) A

SPEED REGULATING VALVES

3/4" (19 mm)

STOP

FACE

1 3/4" (44.5 mm)

6" (152 mm)

1" (25 mm)

1" (25 mm) SCREW & WASHER

HINGE

1. SELECT DEGREE OF OPENING. USE DIMENSIONS SHOWN IN CHART AND ILLUSTRA-

TIONS ABOVE TO MARK LOCATION OF ATTACHING SCREWS ON THE DOOR AND

FRAME. PREPARE HOLES (See Preparation For Fasteners chart, Page 1).

2. ATTACH CLOSER TO THE FRAME WITH THE SPEED REGULATING VALVES FACING THE

HINGE SIDE OF DOOR.

DISASSEMBLE FOREARM FROM MAIN ARM BY REMOVING ELBOW WASHERS AND

SCREW.

4. ASSEMBLE MAIN ARM TO CLOSER USING MAIN ARM SCREW AND LARGE FLAT

WASHER.

5. ATTACH THE FOOT OF THE FOREARM TO THE DOOR.

6. ADJUST THE LENGTH OF THE FOREARM TO POSITION THE FOREARM AT A RIGHT

ANGLE TO THE DOOR TO ENSURE PROPER LATCHING, AND ATTACH FOREARM TO

MAIN ARM USING ELBOW WASHERS AND SCREW.

7. SNAP PINION CAP OVER THE PINION AT THE TOP OF THE CLOSER.

8. ADJUST CLOSER (refer to ADJUSTING SWEEP SPEED & LATCHING SPEED on page 1)

INSTALLATION INSTRUCTIONS

POSITION OF MAIN ARM

WHEN ASSEMBLING TO SPINDLE

POSITION OF MAIN ARM WHEN ASSEMBLING TO

THE PINION SHAFT

RIGHT ANGLE

FRAME

TOP JAMB

RIGHT HAND DOOR

90°

HINGE

SIDE

HINGE

SIDE

MODEL DIMENSION "A" DEGREE OF

OPENING

inches [mm]

UH4051

UH4052

7-5/8" 194 TO 100°

6-1/8" 156 101

TO 130°

4-1/8" 105 OVER 131°

inches [mm]

235

7-3/4"

9-1/4"

5-3/4"

197

146

DIMENSION "B"

PARALLEL ARM INSTALLATION

MODEL UH4051 or UH4052 INSTALLATION INSTRUCTIONS

PAGE 4

999-30003

1. SELECT DEGREE OF DOOR OPENING. USE DIMENSIONS SHOWN IN CHART AND ILLUSTRATIONS ABOVE

TO MARK THE LOCATION OF THE ATTACHING SCREWS ON THE DOOR AND FRAME. PREPARE HOLES.

(See Preparation For Fasteners chart, Page 1).

2. ATTACH CLOSER TO THE DOOR WITH SPEED REGULATING VALVES FACING THE DOOR OPENING.

3. ATTACH THE PA PLATE TO THE TOP FRAME AS SHOWN IN DIAGRAM.

50 Icon, Foothill Ranch, CA 92610-3000 USA

www.hamptonproducts.com • 1-800-562-5625

999-30003_UH4051-52_Eng REVC 12/20

FOR CUSTOMER CARE CALL TOLL FREE

800-562-5625 OR [email protected]

PA PLATE

FRAME

DOOR

SCREW &

WASHER

3/8" (9.5 mm)

2-3/4" (70 mm)

RIGHT HAND DOOR 7/8" (22 mm)

7/16" (11 mm)

FRAME

PA PLATE

1-1/2"

(38 mm)

FOR LEFT HAND DOOR FOR RIGHT HAND DOOR

PINION DIMPLE

PINION DIMPLE DOOR

DOOR

LEFT HAND DOOR RIGHT HAND DOOR

3/4" (19 mm)

STOP FACE

2-3/4" (70 mm)

SPEED REGULATING VALVES

CENTERLINE

OF HINGE

9-1/16" (230 mm) A

HINGE

NSTALLATION INSTRUCTIONS

4. DISASSEMBLE FOREARM FROM MAIN ARM BY

REMOVING ELBOW WASHERS AND SCREW. REMOVE

THE FOOT FROM THE FOREARM AND DISCARD.

NOTE: DO NOT DISCARD SCREW AND WASHERS.

5. BEFORE INSTALLING THE MAIN ARM ON THE PINION

SHAFT, ROTATE THE PINION WITH A WRENCH, 90°

TOWARDS THE HINGE EDGE OF THE DOOR. PLACE

MAIN ARM ON THE PINION, SO THAT THE DIMPLE ON THE

PINION IS TOWARDS THE DOOR. FASTEN MAIN ARM TO

CLOSER WITH MAIN ARM SCREW WITH LOCK WASHER,

AND THE LARGE FLAT WASHER.

6. FASTEN FOREARM WHERE THE FOOT WAS REMOVED

TO THE PA PLATE, USING THE SCREW THAT WAS

REMOVED FROM THE FOOT IN STEP 3 AND PA SHOE

WASHER INCLUDED IN SCREW PACK.

7. WITH THE DOOR CLOSED, ADJUST THE FOREARM

LENGTH TO SET ARM ELBOW ABOUT 1-1/2" [38mm] FROM

THE DOOR WHEN CONNECTED TO THE MAIN ARM. USE

THE ELBOW WASHER AND SCREW PROVIDED TO

SECURE THE PIVOT CONNECTION. TIGHTEN LOCKNUT.

8. SNAP THE PINION CAP OVER THE PINION AT THE

BOTTOM OF THE CLOSER.

9. ADJUST CLOSER (refer to ADJUSTING SWEEP SPEED &

LATCHING SPEED on page 1)

HINGE SIDE

Ce manuel convient aux modèles suivants

Autres manuels UNIVERSAL HARDWARE Serrure de porte

UNIVERSAL HARDWARE

UNIVERSAL HARDWARE UH4031 Manuel utilisateur

Manuels Serrure de porte populaires d'autres marques

Assa Abloy

Assa Abloy effeff 827A-IP Manuel utilisateur

We.lock

We.lock SECBNEBL51 Manuel utilisateur

Iseo

Iseo MA1A Manuel utilisateur

ID Lock

ID Lock 150 Manuel utilisateur

Lockly

Lockly ACCESS TOUCH PRO Manuel utilisateur

iLoq

iLoq G50S Manuel utilisateur

SDC

SDC Z7835 Manuel utilisateur

ilco

ilco 452 Manuel utilisateur

Samsung

Samsung shs-h705 Manuel utilisateur

TRU-BOLT

TRU-BOLT 08102017 Manuel utilisateur

CDVI

CDVI 500-LADJ Manuel utilisateur

Igloohome

Igloohome Deadbolt 2S Metal Grey Instructions d'installation et d'entretien

eSSL

eSSL FL-300 Manuel utilisateur

JAKO

JAKO JKBTNX4 Manuel utilisateur

Dorma

Dorma MUNDUS PREMIUM GK 50 Guide de l'utilisateur

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manuel utilisateur

Yale

Yale MORTISE 8800 SERIES Manuel utilisateur

Siegenia

Siegenia KFV AS3500 Manuel utilisateur