Unipulse F320 Manuel utilisateur

F320

DIGITAL INDICATOR

17 May. 2012

Rev. 1.07

OPERATION MANUAL

INTRODUCTION

The F320 is a digital indicator for a strain gauge sensor, DIN96×48mm in size.

It is best suited for quality control in production lines, including pressure load control of

pressing, pressurizing, caulking, etc., and torque control of rotating devices.

The RS-485 (protocol; Modbus-RTU) is included as standard, which facilitates introduction

into a system that is formed by using the Modbus protocol.

To take full advantage of the F320’s excellent performance and to use it safely, carefully read

this operation manual and properly understand the descriptions in this manual before use.

SAFETY PRECAUTIONS

Be sure to read for safety.

In order to have an F320 Digital Indicator used safely, notes I would like you to surely follow

divide into and , and are indicated by the following documents. Notes

indicated here are the serious contents related to safely. Please use F320 after understanding the

contents well.

WARNING

CAUTION

WARNING

Misuse may cause the risk of death or serious

injury to persons.

CAUTION

Misuse may cause the risk of injury to persons

or damage to property.

SAFETY PRECAUTIONS

WARNING

●For the entire system to function safely when the F320 becomes faulty or malfunctions,

provide a safety circuit outside the F320.

●Do not modify the F320. Doing so may cause fire or electric shocks.

●Do not install in the following environments.

- Places containing corrosive gas or flammable gas.

- Where the product may be splashed with water, oil or chemicals.

●Do not connect a commercial power source directly to the signal input/output

terminals.

●Be sure to ground the protective ground terminal.

●The attached AC cable is designed for domestic use in Japan, and its rating is 125V

AC, 7A. For use at voltages exceeding the rating and for overseas use, have a

separate AC cable prepared.

●Before performing the following, make sure that no power is applied.

- Attachment/detachment of connectors of options, etc.

- Wiring/connection of cables to the signal input/output terminals.

- Connection to the ground terminal.

●For connection to the signal input/output terminals, check the signal names and pin

assignment numbers, and then carry out wiring properly.

●After wiring, be sure to mount the attached terminal block cover. Otherwise, it may

cause an electric shock.

●To take measures against lightning surge, install a lightning surge protector (optionally

available).

●Before applying power, carefully check the wiring, etc.

Warning on design

Warning on installation

Warning on wiring

SAFETY PRECAUTIONS

WARNING

●Use at a proper power supply voltage.

●Do not damage the power cord. Doing so may cause fire or electric shocks.

●Do not touch any signal input/output terminal while applying power. Doing so may

cause electric shocks or malfunctions.

●If the cover of the main body is opened, it may cause an electric shock internally. Even

if the power is off, the internal capacitor is charged. Contact us for internal inspection

or repair.

●In the case of smoke, an abnormal smell or strange sound, immediately turn off the

power, and disconnect the power cable.

Warning during startup and maintenance

SAFETY PRECAUTIONS

CAUTION

●Use the F320 as it is incorporated in a control panel, etc.

●Do not install in the following environments.

- Where the temperature/humidity exceeds the range of the specifications.

- Outdoors, or where the altitude exceeds 2000m.

- Places containing large quantities of salt or iron powder.

- Where the main body is directly affected by vibrations or shocks.

●Take adequate shielding measures when using at the following locations.

- Near a power line.

- Where a strong electric field or magnetic field is formed.

- Where static electricity, relay noise or the like is generated.

●Tighten the screws for the signal input/output terminals at the specified torque.

　If they are loose, shorts, fire or malfunctions may occur.

Tightening torque: 0.2 – 0.6N•m

●For sensors, external inputs/outputs and options, use shielded cables.

●For turning on/off the power, be sure to keep intervals of 5 seconds or more.

●If the F320 is not used by the specified method, its protective performance may be

impaired.

●When the F320 is shipped, spacers made of corrugated cardboard are used as

cushioning materials.

Though it is factory-designed so that shocks can sufficiently be absorbed, breakage

may result if shocks are applied when the spacers are reused for transportation. If you

send the F320 to us for repair, etc., take adequate measures against shocks by using

polyurethane materials, etc., separately.

●If you dispose of the product, handle it as industrial waste.

Caution on installation

Caution on wiring

Caution during startup and maintenance

Caution during transportation

Caution during disposal

CONFORMITY TO EC DIRECTIVES

The F320 digital indicator conforms to EC directives (based on the EC Council of Ministers),

carrying a CE mark.

・Low-voltage directive:IEC/EN61010-1:2001(overvoltage category II)

・EMC directives: EN61326-1:1997, A1:1998, A2:2001

EN55011:1998, A1:1999 ClassA

EN61000-3-2:2000

EN61000-3-3:1995, A1:2001

EN61000-4-2:1995, A1:1998, A2:2001

EN61000-4-3:1996, A1:1998, A2:2001

EN61000-4-4:1995, A1:2001

EN61000-4-5:1995, A1:2001

EN61000-4-6:1996, A1:2001

EN61000-4-8:1993, A1:2001

EN61000-4-11:1994, A1:2001

RoHS-compliant product

The parts and attachments (including the instruction manual, packaging box, etc.) used for

this unit are compliant with the RoHS Directive restricting the use of hazardous substances

with regard to adverse effects on the environment and human body.

What is RoHS?

It is an abbreviation for Restriction on Hazardous Substances, which is implemented by the

European Union (EU). The Directive restricts the use of six specific substances in electric and

electronic equipment handled within EU borders. The six substances are lead, mercury,

cadmium, hexavalent chromium, PBB (polybrominated biphenyls), and PBDE

(polybrominated diphenyl ethers).

EN61000-4-5 (lightning surge immunity)in the EMC directives applies to

the F320 body and lightning surge protector in combination.

For the connection of the lightning surge protector, see page 14.

Please inquire of our sales person about the RoHS-compliance of the option.

CONTENTS OF THE PACKAGE

The following are contained in the package.

Be sure to check before use.

* :It is attached only at the AC power source specification.

AC cable*: One

Terminating resistance: One 3P-2P conversion adapter*: One

F320 operation manual: One

F320

DIGITAL INDICATOR

OPERTATION MANUAL

㧲㧟㧞㧜

㧰㨕㨓㨕㨠㨍㨘

㧵㨚㨐㨕㨏㨍㨠㨛㨞

㧴㧵㧻㧷

㧸㧻㨃

㧼㧱㧭㧷㧴㧻㧸㧰

㧲㧺㧯

㧳㧭㧵㧺

㧯㧭㧸

㨆㧱㧾㧻㧴㧻㧸㧰

F320: One

Ferrite core

(With binding band)

for power cable*: One

Ferrite core

(With binding band)

for sensor cable: One

（For RS-485）

CONTENTS OF THE PACKAGE

ࠩࠟࡀ

࠽࠶࠻㧹㧞

࠽ࡌࠦࡀࠫ㧹㧞㧝㧜㧔㐳㧕

࠽ࡌࠦࡀࠫ㧹㧞㧤㧔⍴㧕

ࠬࠢ࡝ࡘ࡯ࡀࠫ

ࠤ࡯ࠬ㧔㧲㧯㧺㧙㧟㧢㧜㧯㧜㧟㧞㧙㧮㧕

ࠦࡀࠢ࠲㧔㧲㧯㧺㧙㧟㧢㧝㧶㧜㧟㧞㧙㧭㨁㧕

Case (FCN-360C032-B): Two Screws: Two M2 nuts: Four

Connector (FCN-361J032-AU): One

M2×8 pan-head machine screws (short): Two

M2×10 pan-head machine screws (long): Two

Washers: Two

BCD output connector: One set (when the BCO option is equipped)

Case (two)

Screw (two)

Connector

M2×8 pan-head machine screw (short) (two) M2×10 pan-head machine screws (long)

M2 nut (four)

Washer (two)

Assembly

About the power cable

・The power cable attached to this product as standard equipment can be

used in the AC100V power supply in Japan. (Official ratings voltage

AC125V)

Please use the power cable authorized in the country when you use this

product outside Japan.

CONTENTS

1．FUNCTIONAL DESCRIPTIONS .............................................1

1-1．Front Panel ............................................................................................ 1

1-1-1Status Display ..................................................................................... 1

1-1-2Numerical Display ............................................................................... 2

1-1-3Setting Key Pad ................................................................................... 3

1-2．Rear Panel ............................................................................................. 5

1-2-1Protective Ground ............................................................................... 5

1-2-2Frame Ground (Frame terminal) ........................................................ 5

1-2-3Options Slot ......................................................................................... 5

1-2-4AC Power Input Terminal Block ........................................................ 6

1-2-5Signal Input/Output Terminal Block .................................................. 6

2．INSTALLING IN A CONTROL PANEL ....................................8

3．CONNECTION ........................................................................9

3-1．Connecting Strain Gauge Sensor ..................................................... 10

3-2．Connecting Power Input Terminal .................................................... 12

3-2-1AC Spec. ............................................................................................ 12

3-2-2DC Spec. ( Depending on the request at the time of order ) ......... 15

3-3．Connecting High / Low Limit Relays ................................................. 18

3-4．Connecting Hold and Digital Zero Signals ....................................... 19

3-5．Connecting Analog monitor Output (VOL OUT) .............................. 20

4．SETTING MODE CONFIGURATION ....................................21

4-1．Selection of Setting Items .................................................................. 21

4-2．Display of Setting Items ..................................................................... 23

4-3．List of Values ...................................................................................... 25

4-4．Setting Procedure ............................................................................... 28

Table des matières

Autres manuels Unipulse Instrument de mesure

Unipulse

Unipulse USH-10KN Manuel utilisateur

Unipulse

Unipulse F370 Manuel utilisateur

Unipulse

Unipulse F377A Manuel utilisateur

Unipulse

Unipulse UTM II-20Nm Manuel utilisateur

Unipulse

Unipulse TM201 Manuel utilisateur

Unipulse

Unipulse TM500 Manuel utilisateur

Unipulse

Unipulse TM400 Manuel utilisateur

Unipulse

Unipulse F372A Manuel utilisateur

Unipulse

Unipulse F701+ Manuel utilisateur

Unipulse

Unipulse F340A Manuel utilisateur

Unipulse

Unipulse F325 Manuel utilisateur

Unipulse

Unipulse UPM100 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur