ULNA CPE-609 Manuel utilisateur
WIRELESS BRIDGE
Tips:
Thank you for ordering and using ULNA CPE609 Wireless Bridge, please read
the manual carefully before use. If there are any problems during the use,
please contact us in time.
The installation of this device requires some network knowledge. If you can't
install it, please let us know or contact a professional.
Customer Service Email: [email protected]
Model: CPE-609
USER MANUAL
Contents
1. Overview
1.1 Introduce
1.2 Highlights
1.3 Specifications
2. Package Included
3. Interface Details
3.1. Button Operation
4. LED Indicator Details
5. Quick Start
5.1 PoE Power Supply
5.2 Point to Point Pairing Step
5.3 Point to Multipoint Pairing Step
6. Installation
6.1 Pole mount
6.2 Wall-mounted
6.3 Connect to the device
7. WiFi Function
8. Application Case
8.1 Case 1: PTP extended network WiFi range
8.2 Case 2: PTP extended of surveillance cameras range
8.3 Case 3: PTMP extended surveillance cameras range
8.4 Case 4: PTP extended surveillance cameras range
9. Advanced Settings
10. Troubleshooting
11. Technical Support and Service
1
1
1
2
3
3
4
4
5
5
5
6
6
6
7
7
8
8
8
9
9
9
10
13
15
1. Overview
1.1 Introduce
01
ULNA CPE609 is a long-distance 5.8G wireless transmission device. It uses
wireless communication technology to transmit network data using air as a
medium to perform long-distance point-to-point or point-to-multipoint
interconnection. The working data link layer realizes the interconnection of
local area networks. The transmission distance can reach up to 5km.
CPE609 Video Bridge Transmission usually consists of two devices in AP and
Client mode respectively. On the Client-side (Receiving side) CPE connects with
IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder.
The AP can be receiving wireless data transmitted from multiple Clients, and it
is easy and convenient for centralized management of the remote equipment.
CPE is widely used in highways, reservoir river monitoring, elevator monitoring
systems, site crane monitoring systems, port terminal monitoring systems,
marine aquaculture monitoring systems, and so on.
Point to point extend network WiFi range, extend the network in the house to
your barn, garage, church, warehouse, and even neighbor's house through
wireless bridge signal transmission. No need to install a new modem and pay
for it every month, saving you money.
1.2 Highlights
1. Transmission using 5.8Ghz wireless technology；
2. 1000Mbps RJ45 LAN port, support Gigabit；
3. Built-in 16dbi high gain WiFi antenna；
4. IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u；
5. Transmission distance up to 5km(Barrier-Free)；
6. Master bridge supports WiFi hotspot access；
7. Dialing to set the transmitter and receiver, is easy to use；
8. WDS networking mode, video network dual compatible；
9. Support point-to-point, point-to-multipoint mode；
10. Dynamic MIMO power saving mode (DMPS) and APSD；
11. Support 24V POE power supply, easy to install and deploy；
12. Support WEB GUI access management device.
1.3 Specifications
ULNABrand
CPE-609Model
MT7620A+7612ECPU
8MByteFlash
DDR2 128MByteDRAM
10/100/1000Mbps LAN*1 & 10/100Mbps LAN*1
Interface
11a:54M,48M,36M,24M,18M,12M,9M,6Mbps
11n:7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,
72.2M,14.4M,28.9M,43.3M,57.8M,86.7M,115.6M,
130M,144.4Mbps 433Mbps
Data rate
Direct Sequence Spread Spectrum(DSSS)Transfer method
OFDM/BPSK/QPSK/CCK/DQPSK/DBPSKModulation
IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3uProtocol standard
4900～6100MHzFrequency Range
≤3W, POE 24V~1A/48V~0.5APower
16dBi,Horizontal 60°/Vertical 30°Antenna
SupportWEP GUI
SupportTelnet
SupportSerial
WEP 64/128bits,WPA,WPA2,802.1xSafety
-30～65℃Temperature
11.8*11.5*2.7 inch & 2.2 LBBox Size & Weight
CSMA/CA,TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3,
NDIS4,NDIS5
Agreement
2. Package Included
3. Interface Details
03
2 * CPE609 Gigabit Bridge
2 * Gigabit POE Adapter (24V)
2 * Cat 5e Network Cable
2 * Metal Hoop
1* Mounting Screw Set
1 * User Manual
WIRELESS BRIDGE
Tips:
Thank you for ordering and using ULNA CPE609 Wireless Bridge, please read
the manual carefully before use. If there are any problems during the use,
please contact us in time.
The installation of this device requires some network knowledge. If you can't
install it, please let us know or contact a professional.
Customer Service Email: [email protected]
Model: CPE-609
USER MANUAL
Power indicator
Reset Button
LAN1/LAN2
WLAN Signal Light
1000Mbps LAN
DC(Unavailable)
Fixed Bracket
Universal Ball Head
Digital Tube
A-B Button
100Mbps LAN
1000Mbps
LAN Port
Gigabit PoE
Adapter
PoE Port
LED
Horizontal Ruler
4. LED Indicator Details
3.1. Button Operation
Reset Button: Press and hold for 10S to reset the wireless bridge; in setup mode,
short press once to toggle a different character to pairing.
A-B Button: Pushing the button to "A" indicates that the bridge acts as the
master bridge (transmitter), and pushing the button to "B" indicates that the
bridge acts as the slave bridge (receiver).
DescriptionLED Light
Power indicator, the LED is on after the power is
connected
PWR
Digital display LED display "H" indicates manual
configuration status
Digital Tube
Digital display LED display "L" and flashing indicates
settings status
Digital Tube
Digital display LED flashing indicates edit the config
or connecting
Digital Tube
After the bridge is connected successfully, the
WLAN light will be on, not connected the WLAN
light will not be lit.
Signal Lights
The data connection is successful, the LED light is
on, otherwise, it is not bright.
LAN1/LAN2
5. Quick Start
05
5.1 PoE Power Supply
The CPE609 wireless bridge adopts a PoE power supply, which is easy to install
and manage while saving costs.
5.2 Point to Point Pairing Step:
1. Switch one unit to A(Master Bridge) and one unit to B(Slave Bridge)
2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a letter.
1,2,3,..., A,B,C,...,F, here used C;
5. Then on the other unit do the same. Both units need to be on the same channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the digital
tube is solid and the signal light on the side turns on, it means the pairing is
successful;
1.1. According to the requirements, prepare a long enough network cable
（Recommended within 20 meters, must Cat 5e or up） to connect the wireless
bridge and the PoE power supply. The PoE port of the PoE power supply is
connected to the WAN port of the wireless bridge.
1.2. The LAN port of bridge is connected to the PC, router, and switch...
Display that a fixed number is solid, it means that
the two bridges are paired successfully and are
working.
Digital Tube
A, B status lights, lighting is B mode, no lighting is
A mode.
Point Light
6. Installation
5.3 Point to Multipoint Pairing Step:
6.1 Pole mount
e.g. 1 master bridge with 3 slave bridges
1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge);
2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a letter.
1,2,3,..., A,B,C,...,F, here used C;
5. Then on the other 3 unit do the same. 4 units need to be on the same channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the digital
tube is solid and the signal light on the side turns on, it means their pairing is
successful;
7. Finally connect other devices(Router, PC, Switch) and install them to the target
location.
7. Finally connect other devices(Router, PC, Switch) and install them to the target
location.
（TIPS:Steps 1, 4 and 5 are already pre-set）
7. WiFi Function
8. Application Case
1. Choose to pole mount or wall-mounted, adjust the CPE orientation, the
bracket is not included in the package. Recommended ULNA Universal Bracket
(ASIN: B0B5TWYHWC).
2. Please, prepare a long enough network cable to connect the PoE adapter and
CPE, the network cable is connected to the LAN port of the CPE, and the other
end is connected to the PoE port of the PoE adapter. Recommend to use a cat 5
(or above) shielded network cable with a ground wire.
3. Connect the PoE adapter PoE to CPE, and LAN to Camera, PC, Router or Switch
based on the network topology. The role of PoE is to provide power and data t
ransmission for CPE.
4. The master CPE’s PoE adapter’s LAN connection monitors the Internet,
and the slave CPE’s PoE adapter LAN connects cameras or routers and other
equipment.
1. The WiFi function is turned on by default for the master bridge.
WiFi SSID: CPE5G-5GXXX
WiFi PWD: zllinkcpe123456XXX
XXX represents different channels, please refer to the comparison table in the
user manual.
2. You can access the wireless bridge through your computer to set the SSID and
new WiFi password. Please refer to the advanced settings section.
8.1 Case 1: Point-to-point extended network WiFi range
suitable for extending the network to second buildings, such as garages, shops,
barns,etc.
Table des matières
Autres manuels ULNA Matériel réseau
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
