UFO MicroLED 4000P Fiche technique

PRODUCT USER GUIDE

M croLED 4000P L ght Source

PLEASE READ THIS USER GUIDE BEFORE INSTALLING, OPERATING

OR PERFORMING MAINTENANCE ON THE LIGHT SOURCE UNIT

E357731

Rev: C2

INTRODUCTION

MICROLED 4000P USER GUIDE

Thank you for purchasing this UFO ight source/ uminaire.

To ensure that the ight source is set up optima y and gives a ong service ife, p ease read this

user guide before insta ing, operating or performing any maintenance on the unit.

P ease keep this User Guide for future reference. This User Guide is aid out in three sections

Insta ation -detai s on how to connect your uminaire

Operation - detai s how to programme and set up your uminaire

Maintenance - maintenance og, troub eshooting guide, technica specification

MODELS COVERED BY THIS USER GUIDE

UFO MIC4000P

IMPORTANT

This product must be insta ed in accordance with the app icab e insta ation code, by a person

fami iar with the construction and operation of the product, and the hazards invo ved.

These ight sources are not mains dimmab e.

The LED array in this ight source is not rep aceab e. When it reaches end of ife the who e unit

must be rep aced.

Type Y Attachment: If the externa f exib e cab e or cord of this uminaire or associated

PSU/driver is damaged, it sha be exc usive y rep aced by the manufacturer or his service agent

or a simi ar qua ified person to avoid a hazard.

Location: Do not ocate this ight source c oser than 200mm from any f ammab e surface.

C earance / Venti ation: It is imperative that a gap of 200mm is e around the unit. This is to

a ow air to circu ate and prevent overheating. The ocation must have free venti ation and must

not have an ambient temperature higher than that specified for the uminaire.

Mounting: This uminaire comes with an integra mounting p ate for securing the unit to a

vertica or horizonta surface. Refer to the instruction sheet supp ied with the p ate.

Warning: Never ook direct y at the uminaire through the fibre port of the ight source.

Warning: The uminaire shou d be positioned so that pro onged staring into the

uminaire at a distance c oser than 2.7 metres is not expected.

This uminaire is powered by a 12V Power Supp y Unit or 12V Constant Vo tage Driver. Remove

the PSU/driver from its box. Connect the jack p ug into the socket in the back, and the ight

source is now ready for connection.

POWER SUPPLY REQUIREMENTS

INSTALLATION

UFO LIGHTING

This uminaire supp ied with a separate mounting p ate. If using the mounting p ate refer to the

fitting instructions supp ied with it.

MOUNTING

There are 2 connections required - the fibre port and the mains supp y. The fibre port shou d be

connected first. Connect and secure the fibre optic connector into the front of the unit and

secure using the M5 ocking screw.

P ug the mains p ug into the e ectrica supp y socket. Switch on the power, the LED indicator

wi i uminate, and the ight source wi start up automatica y. If no ight is produced consu t

the troub eshooting section.

CONNECTION

REMOTE CONTROL

Descripon Details Comments

Power 2 x AAA baeries -

Range 30 metres Measured in free space, may be aenuated by

obstrucons or other RF devices

Frequency 2.4GHz Approved for use in UK, USA and Europe

With The ight source powered up as described

above, remove the rear cover on the remote contro

unit. Taking care not to touch any of the front

buttons, insert the batteries.

If you touch the remote contro buttons when

inserting the batteries it WILL eﬀect the operation of

your remote contro . If you do accidenta y touch any

of the buttons, remove the batteries and start again.

Once the batteries are inserted do not use the

remote contro for 3 seconds.

BATTERIES

The remote contro unit is matched with the ight source at the factory.

If the remote contro is not matched or an additiona or rep acement remote contro is required

carry out the “Matching Remote to Light Source” instructions as detai ed ater in this guide.

If a remote contro is to be removed from contro of a ight source carry out the “Unmatching

Remote to Light Source” instructions as detai ed ater in this guide.

FURTHER INFORMATION

INSTALLATION

MICROLED 4000P USER GUIDE

REMOTE CONTROL OPERATION

No. Descripon Funcon

1 Buon Power on

2 Buon Power oﬀ

3 Colour Ring Touch control all colours (white not available)

4 Indicator Indicates controller acve when buons pressed

5 Buon Increase colour cycle speed

6 Buon Increase brightness

7 Buon Decrease brightness

8 Buon Decrease colour cycle speed

9 Buon [Mode +] Step up through colour cycle programmes

10 Buon [Mode -] Step down through colour cycle programmes

OPERATION

UFO LIGHTING

MATCHING REMOTE CONTROL UNIT TO LIGHT SOURCE

Remove the power p ug from the rear of the Light Source, then

rep ace and touch button 5 within 3 seconds, the Light Source

wi “b ink” twice s ow y indicating that the Remote Contro er

is matched to the Light Source.

UNMATCHING REMOTE CONTROL UNIT FROM LIGHT SOURCE

Remove the power p ug from the rear of the Light Source, then

rep ace and touch and ho d button 5 within 3 seconds and the

Light Source wi “b ink” 9 times indicating that the Remote

Contro er is unmatched from the Light Source.

Note:

More than one Light Source contro ed by one Remote Contro er wi

eventua y run out of sync with each other (co our cyc e mismatch)

REMOTE CONTROL MODES AND FUNCTIONS

Mode Buttons – Do not work in a oop, i.e. touching the mode+ button wi not eventua y bring

you back to mode 1. To revert to mode 1, either touch mode – button repeated y to step back

up through the mode numbers, or touch co our ring then mode+

Co our Ring –The co our ring can be used to se ect individua co ours by touching the ring

and s iding your finger around the ring,

Brightness – brightness can be increased or reduced in any mode using buttons 6 & 7

Cyc e Speed – speed of co our cyc ing in modes 3 to 14 can be adjusted using buttons 5 & 8

No. Mode Brightness Speed Comment

1 Stac white Adjustable Non adjustable

Touch colour ring then

mode + to enter this

mode at any me

2White and

colours mixed Adjustable Non adjustable

Colour ring control. Touch

colour ring to enter this

mode at any me

3 All colours fade Adjustable Adjustable No white

4 RGBW fade Adjustable Adjustable Red, green, blue, white

5 RGBW snap Adjustable Adjustable Red, green, blue, white

6 7 colours snap Adjustable Adjustable White and colours mixed

7 2 colours snap Adjustable Adjustable Red and white

8 2 colours snap Adjustable Adjustable Blue and white

9 2 colours snap Adjustable Adjustable Green and white

10 1 colour ﬂash Adjustable Adjustable Red

11 1 colour ﬂash Adjustable Adjustable Blue

12 1 colour ﬂash Adjustable Adjustable Green

13 1 colour ﬂash Adjustable Adjustable White

14 All colours

snap/fade Adjustable Adjustable Random

OPERATION

MICROLED 4000P USER GUIDE

REMOTE RANGE WALK TEST

Once the ight source is fu y insta ed carry out a comp ete range wa k test and record the range

in the tab e be ow.

This information is essentia for maintenance purposes to determine if the range/sensitivity is

reducing and a so to record dead areas within the remote contro units range due to RF

obstructions and/or RF interference.

Note: Where a ight source has more than one remote contro , reduction in operating range may

be experienced when both (or mu tip e) remote contro s are used simu taneous y.

Descripon Date Max Range

Controller 1

Controller 2

Controller 3

Dead Areas

OPERATION

UFO LIGHTING

To disab e the remote and revert to manua operation press one of the buttons on the rear of

the ight source. The ight source wi now respond to manua commands from the 2 contro

buttons as described be ow.

The ight source has 2 co our cyc es, each with 3 diﬀerent speed settings, the co ours are

detai ed in the tab e be ow:

STANDALONE OPERATION USING INBUILT BUTTONS

Cycle Colour 1 Colour 2 Colour 3 Colour 4 Colour 5 Colour 6 Colour 7

1 White Red Orange Jade Green Cyan Blue

2 Red Orange Jade Green Cyan Blue White

The ight source is contro ed using the 2 push buttons on the rear of the unit.

The ower button stops and starts the co our cyc e.

The upper button is used to se ect the cyc e speed as fo ows:

Push the upper button repeated y unti the co our white is disp ayed. The ight source is now in

Cyc e 1 Speed A as detai ed in the tab e be ow. Each push reduces the speed. On the third push,

the co our red wi be disp ayed. The ight source is now in Cyc e 2 Speed A.

At any time the cyc e can be stopped on a co our and started again using the ower push

button.

To disab e manua operation and revert to remote contro operation, recyc e the power to

the ight source. The remote contro unit may need to be matched to the ight source as

detai ed on page 5.

Cycle Speed A - Fastest Speed B - Slower Speed C - Slowest

1 (White Start) Push once Push once Push once

2 (Red Start) Push once Push once Push once

OPERATION

MICROLED 4000P USER GUIDE

The MicroLED 4000 is programmed as a Master unit and is capab e of inter inking to and

contro ing MicroLED S ave Light Sources using a RJ45 cab e inking the two. In this Master

/S ave configuration the S ave Light Source wi fo ow the Master Light Source. The MicroLED

4000 Master Light Source, cannot be contro ed by a remote DMX contro er.

For the MicroLED 4000, remote DMX s ave contro can on y be achieved with MicroLED 2000

or MicroLED 4000 S ave Light Sources. See MicroLED 2000 or MicroLED 4000 S ave User Guides

for DMX wiring connections

DMX OPERATION

MAINTENANCE LOG

Date Maintenance Undertaken

Note: A record of a maintenance MUST be kept in the tab e above, indicating what maintenance

was undertaken and when. This MUST be dated for warranty purposes.

OPERATION & MAINTENANCE

UFO LIGHTING

Problem Possible Cause(s) Remedy

Unit is dead - LED

power

indicator is not

illuminated

Mains supply oﬀ Check supply and reinstate

Loose mains plugs Check plugs

PSU failed Replace PSU

Unit is dead - no

light output but LED

power indicator is

sll illuminated

LED array failure Replace LED unit

Switched oﬀ via remote control unit Recycle power to light source or switch on via

remote control

Poor light

output on bre

Unit needs cleaning

Carefully clean LED Lens

with dry cloth

Clean bre common end

Fibre port connector not

plugged in correctly

Ensure plugged in correctly

and secured with locking screw

Staonary on one

colour

Lower buon has been pressed Press lower buon once

LED driver has failed Replace LED unit

Colour cycle cannot

be stopped LED driver has failed Replace LED unit

Remote control

range reduced

or persistently

freezing

Baeries failing Replace baeries as per user guide and carry out

matching if necessary

Interference from external source Check for another device transming

RF interference

Remote control needs reset Remove and replace baeries as per user guide

Remote control failing Replace remote control unit

Light source receiver failing Replace light source

Light source

won’t

respond to

remote control

unit

Baeries failed Replace baeries as per user guide and carry out

matching if necessary

Light source in standalone mode Recycle power to light source

Remote control needs reseng Remove and replace baeries as per user guide

Remote control not matched to light source Carry out matching procedure as

detailed in user guide

Remote control failed Replace remote control unit

Light source receiver failed Replace light source

In master/slave

con guraon, slave

light source works

on standalone but

does not respond to

DMX from master

DMX cable disconnected or faulty Check DMX link cable connecons -

repair or replace

Master light source not

sending DMX signal

Check master light source - refer to the relevant

user guide troubleshoong secon

TROUBLESHOOTING

MICROLED 4000P USER GUIDE

Autres manuels pour MicroLED 4000P

Table des matières

Autres manuels UFO Équipement d'éclairage

UFO

UFO Sirius UFOSIRCW Manuel utilisateur

UFO

UFO MicroLED 100P Series Fiche technique

UFO

UFO Illuminator 150 CDMXG Manuel utilisateur

UFO

UFO Vega Fiche technique

UFO

UFO Comet Light Source Fiche technique

UFO

UFO LUNA SLP-3000M Manuel utilisateur

UFO

UFO MICROLED 2000 Manuel utilisateur

UFO

UFO MicroLED 1000P Fiche technique

UFO

UFO MIC100PT-3 Manuel utilisateur

UFO

UFO MIC4000x2 Manuel utilisateur

UFO

UFO MicroLED 4000P Fiche technique

UFO

UFO MicroLED 4000P Fiche technique

UFO

UFO MicroLED 3000 Fiche technique

UFO

UFO MBL1 Manuel utilisateur

UFO

UFO LPV2 Manuel utilisateur

UFO

UFO LUNA SLP-3000M Fiche technique

UFO

UFO MicroLED 100PT Fiche technique

UFO

UFO MicroLED 4000P Fiche technique

UFO

UFO UFO MER3000M Manuel utilisateur

UFO

UFO MBL2 Manuel utilisateur

UFO

UFO Unidrive CC9 Fiche technique

UFO

UFO LP5 LED Paver Manuel utilisateur

UFO

UFO Nova Light Source Fiche technique

UFO

UFO GEM SLP-3000M Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur