Ubiquiti NanoBeam M2 Manuel utilisateur
High-Performance 13 dBi
airMAX®CPE
Model: NBE-M2-13
All manuals and user guides at all-guides.com
Introduction
Thank you for purchasing the Ubiquiti Networks®NanoBeam®.
This Quick Start Guide is designed to guide you through
the installation, and show you how to access the airOS®
Configuration Interface. This Quick Start Guide also includes
the warranty terms and is for use with the NanoBeamM2,
modelNBE-M2-13.
Package Contents
NanoBeamM2 Ball Joint
Mount
Lock Ring
High-Performance13 dBi
airMAX®CPE
Model:NBE-M2-13
Metal Strap PoE Adapter with
Mounting Bracket
(24V, 0.5A)
Power Cord Quick Start
Guide
TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet
cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is
designed for outdoor installations. It is the customer’s responsibility to follow local country
regulations, including operation within legal frequency channels, output power, and Dynamic
Frequency Selection (DFS) requirements.
All manuals and user guides at all-guides.com
Installation Requirements
The NanoBeam can be mounted on a pole or to a wall. A Metal
Strap (included) is used for pole-mounting. For wall-mounting,
a suitable fastener such as a screw or bolt (not included) is
required.
• Pole-mounting: 7 mm socket wrench or screwdriver
• Wall-mounting: wall fastener (not included)
• Shielded Category 5 (or above) cabling should be used for
all wired Ethernet connections and should be grounded
through the AC ground of the PoE.
We recommend that you protect your networks from the
most brutal environments and devastating ESD attacks with
industrial-grade shielded Ethernet cable, TOUGHCable from
Ubiquiti Networks.
For more details, visit www.ubnt.com/toughcable
Hardware Overview
LEDs
Reset Button Ethernet Port
(10/100 Mbps)
All manuals and user guides at all-guides.com
Reset Button To reset to factory defaults, press and hold the
Reset button for more than 10 seconds while the NanoBeam
is already poweredon. Alternatively, the NanoBeam may be
reset remotely via a Reset button located on the bottom of the
PoE Adapter.
Ethernet Port The Ethernet port is used to connect the power
and should be connected to the LAN and DHCP server. Power
can be provided by any of the following:
• PoE Adapter (included)
• Ubiquiti Networks EdgeSwitch™
• Ubiquiti Networks EdgeRouter™ PoE
LEDs
Power The Power LED will light blue when the
device is connected to a power source.
Ethernet The Ethernet LED will light steady blue
when an active Ethernet connection is made and
flash when there is activity.
Signal The default values are shown below:
LED will light blue when the wireless signal
strength is equal to or above -94 dBm.
LED will light blue when the wireless signal
strength is equal to or above -80 dBm.
LED will light blue when the wireless signal
strength is equal to or above -73 dBm.
LED will light blue when the wireless signal
strength is equal to or above -65 dBm.
All manuals and user guides at all-guides.com
Hardware Installation
The NanoBeam can be mounted on a pole or to a wall. Perform
the steps for the appropriate installation:
Pole-Mount
1. Insert the Ball Joint Mount into the Lock Ring with the
threads of the Lock Ring facing the ball joint.
2. Open the Metal Strap and feed it through the base of the
Ball Joint Mount.
All manuals and user guides at all-guides.com
3. Wrap the Metal Strap around the pole. Use a 7 mm socket
wrench to turn the screw clockwise and securely fasten the
clamp to the pole.
4. Attach the NanoBeam to the Ball Joint Mount and turn the
Lock Ring to secure it. Keep the Lock Ring loose enough to
allow the NanoBeam to pivot for aiming.
All manuals and user guides at all-guides.com
Wall-Mount
The NanoBeam must be mounted directly to a wood stud
or other structurally stable surface to avoid damage to the
mounting hole when you adjust the aim.
Optional Accessory
To enhance stability, you can use the NanoBeam Wall Mount
Kit, model NBE-WMK (soldseparately).
Note: Center screw included. Two optional screws
(not included) provide additional stability.
Installation Instructions
1. Mark the desired location of the mounting point.
2. If needed, drill a pilot hole for the fastener (not included).
3. Insert the Ball Joint Mount into the Lock Ring with the
threads of the Lock Ring facing the ball joint.
All manuals and user guides at all-guides.com
4. If you are using the optional NanoBeam Wall Mount Kit,
then skip to step b.
a. To attach the Ball Joint Mount to the wall, insert a
fastener (not included) through the center of the ball
joint, and into the wall. Securely tighten the fastener.
Proceed to step 5.
b. To attach the Ball Joint Mount to the wall, insert the Wall
Mount Kit screw through the center of the ball joint,
through the Wall Mount Kit plate, and into the wall.
Securely tighten the screw.
All manuals and user guides at all-guides.com
5. Attach the NanoBeam to the Ball Joint Mount and turn the
Lock Ring to secure it. Keep the Lock Ring loose enough to
allow the NanoBeam to pivot for aiming.
Aiming
1. Ensure the opening of the Ethernet cable is pointed
towards the ground.
2. Aim the front of the NanoBeam towards the other end of
the wireless link.
3. Hand-tighten the Lock Ring to lock the aim.
Note: Do not use a tool to tighten the Lock Ring.
Tighten the Lock Ring by hand only.
All manuals and user guides at all-guides.com
Connecting to the PoE Adapter
1. Remove the port cover by pressing down on the center of
the cover and sliding the cover out.
2. Connect an Ethernet cable to the Ethernet port.
3. Replace the port cover.
All manuals and user guides at all-guides.com
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Ubiquiti Point d'accès sans fil
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Ubiquiti
Ubiquiti PBE-M5-400 Manuel utilisateur
Ubiquiti
Ubiquiti UniFi XG Instructions d'utilisation et d'entretien
Ubiquiti
Ubiquiti UAP-AC-M Manuel utilisateur
Ubiquiti
Ubiquiti UniFi Switch Flex Manuel utilisateur
Ubiquiti
Ubiquiti NBE-5AC-Gen2 Manuel utilisateur
Ubiquiti
Ubiquiti NBE--2AC--13 Manuel utilisateur
Ubiquiti
Ubiquiti airFiber AF-11 Manuel utilisateur
Ubiquiti
Ubiquiti NanoStationM Series Manuel utilisateur
Ubiquiti
Ubiquiti UniFi UAP-nanoHD Manuel utilisateur
Ubiquiti
Ubiquiti UAP-AC-LITE-5 Manuel utilisateur
Ubiquiti
Ubiquiti GigaBeam Manuel utilisateur
Ubiquiti
Ubiquiti PBE-M5-300-US Manuel utilisateur
Ubiquiti
Ubiquiti PowerBeam AC PBE-5AC-620 Manuel utilisateur
Ubiquiti
Ubiquiti IS-5AC Manuel utilisateur
Ubiquiti
Ubiquiti UAP-IW-HD Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Ubiquiti
Ubiquiti LiteBeam LBE-5AC-16-120 Manuel utilisateur
Ubiquiti
Ubiquiti Uni-fi AP Manuel utilisateur
Ubiquiti
Ubiquiti NanoBeam ac Manuel utilisateur
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
Buffalo
Buffalo AirStation WLA-L11G Manuel utilisateur
