Ubiquiti EdgeSwitch ES-16-150W Manuel utilisateur

Managed PoE+ Gigabit Switch

with SFP

Model: ES-16-150W

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch®.

This Quick Start Guide is designed to guide you through the

installation and also includes the warranty terms.

Package Contents

EdgeSwitch ES-16-150W

Power Cord Mount Brackets

(Qty. 2)

Bracket Screws

(Qty. 8)

Mounting Screws

(Qty. 4)

Cage Nuts

(Qty. 4)

Rubber Feet

(Qty. 4)

installer’s responsibility to follow local country regulations, including operation within legal

frequency channels, output power, indoor cabling requirements, and Dynamic Frequency

Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver (for rack or wall mounting)

• Standard-sized, 19" wide rack with a minimum of 1U height

available (for rack mounting)

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the switch to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeSwitch itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel Ports

RJ45 1-16 SFP 1-2

Port Description

RJ45 1-16 RJ45 ports support 10/100/1000 Ethernet

connections.

SFP 1-2 Hot-swappable SFP ports support 1 Gbps

connections.

Front Panel LEDs

System

System LED

Note: The System LED functionality has been updated

with firmware v1.8.0. We recommend that you update

the EdgeSwitch to the latest firmware.

State Status

Flashing White Bootup in progress.

White Ready for use, not connected to Ubiquiti®

Network Management System (UNMS™).

Blue Ready for use, connected to UNMS.

Steady Blue

with Occasional

Flashing

Ready for use, unable to connect to

UNMS, check connection to UNMSserver.

Quickly Flashing

Blue Used to locate a device in UNMS.

Alternating

Blue/White Firmware upgrade in progress.

You can use the EdgeSwitch Configuration Interface or UNMS

to manage your device. UNMS lets you configure, monitor,

upgrade, and back up your devices using a singleapplication.

Get started at www.unms.com

RJ45:

PoE

RJ45:

Speed/Link/Activity

SFP:

Speed/Link/Activity

RJ45 LEDs

LED State Status

PoE

Off No PoE

Amber IEEE 802.3af/802.3at

Green 24V Passive

Speed/

Link/

Activity

Off No Link

Amber Link Established at 10/100 Mbps

Amber

Flashing Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps (1 Gbps)

Green

Flashing Link Activity at 1000 Mbps (1Gbps)

SFP LEDs

LED State Status

Speed/

Link/

Activity

Off No Link

Green Link Established at 1 Gbps

Green

Flashing Link Activity at 1Gbps

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeSwitch to factory defaults:

Runtime Reset (Recommended)

The EdgeSwitch should be running after

bootup is complete, and the System LED

is white. Press and hold the Reset button.

The EdgeSwitch will reboot, and the System

LED becomesblue after three seconds.

Continue to hold the Reset button for

about 15seconds until the System LED

flashes blue for two seconds. This indicates

that the EdgeSwitch has reset to its

factorydefaults.

Power-on Reset

1. Disconnect the Power Cord from the

EdgeSwitch.

2. While connecting the Power Cord to

the EdgeSwitch, hold the Reset button

for about 15seconds until the System

LED flashes blue for two seconds. This

indicates that the EdgeSwitch has reset

to its factory defaults.

Back Panel Console Port

Console

Port Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect

the Console port to your computer. Then

configure the following settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

Hardware Installation

The EdgeSwitch can be placed on a horizontal surface,

mounted in a rack, or mounted on a wall.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Place the Rubber Feet on the bottom of the EdgeSwitch if you

do not plan to mount it. For rack or wall mounting, follow the

appropriate steps:

Rack Mounting

1. Attach the Mount Brackets to the EdgeSwitch using the

eight Bracket Screws, positioning the brackets as shown

below.

2. Attach the EdgeSwitch to the rack using the four Mounting

Screws. (If the rack has square slots, then use the Cage Nuts

with the Mounting Screws.)

Wall Mounting

1. Attach the Mount Brackets to the EdgeSwitch using the

eight Bracket Screws, positioning the brackets as shown

below.

2. Secure the EdgePower to the wall using the appropriate

fasteners and anchors (not included) for the wall.

Connecting Power

1. Connect the Power Cord to the Power port of the

EdgeSwitch.

2. Plug the Power Cord into a power outlet.

Autres manuels pour EdgeSwitch ES-16-150W

Table des matières

Autres manuels Ubiquiti Changer

Ubiquiti

Ubiquiti UniFi US-8 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi SWITCH 48 Manuel utilisateur

Ubiquiti

Ubiquiti USW-24 Manuel utilisateur

Ubiquiti

Ubiquiti ETHERMAGIC EM-S Manuel utilisateur

Ubiquiti

Ubiquiti US-16-XG Manuel utilisateur

Ubiquiti

Ubiquiti ES-24-250W Mode d’emploi

Ubiquiti

Ubiquiti EdgeSwitch Manuel utilisateur

Ubiquiti

Ubiquiti ES-24-250W Manuel utilisateur

Ubiquiti

Ubiquiti EdgeSwitch 10 XP Manuel utilisateur

Ubiquiti

Ubiquiti unifi switch 8 Manuel utilisateur

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE Manuel utilisateur

Ubiquiti

Ubiquiti ES-24-250W Manuel utilisateur

Ubiquiti

Ubiquiti FiberPoE Manuel utilisateur

Ubiquiti

Ubiquiti EdgeSwitch 8 Manuel utilisateur

Ubiquiti

Ubiquiti US-XG-6POE Manuel utilisateur

Ubiquiti

Ubiquiti ES-24-250W Manuel d'installation

Ubiquiti

Ubiquiti EdgeSwitch ES-10XP Manuel utilisateur

Ubiquiti

Ubiquiti USW-Flex Manuel utilisateur

Ubiquiti

Ubiquiti ES-24-250W Manuel utilisateur

Ubiquiti

Ubiquiti UniFi USW-24-POE Manuel utilisateur

Ubiquiti

Ubiquiti UniFi US-24-500W Manuel utilisateur

Ubiquiti

Ubiquiti EdgeSwitch 48 LITE Manuel utilisateur

Ubiquiti

Ubiquiti UniFi US-48-750W Manuel utilisateur

Ubiquiti

Ubiquiti UniFi USW-Industrial Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur