Ubiquiti G3 Micro Manuel utilisateur

micro

1080p Wireless IP Security

Camera with Infrared

Model: UVC-G3-MICRO

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi® Video

Camera G3 Micro. This Quick Start Guide is designed to guide

you through installation and also includes warranty terms.

Package Contents

UVC-G3-MICRO Camera Power Adapter

802.3af Instant

PoE Adapter

Instant PoE Cover Table Stand

Wall Mounts

(Qty. 2)

Instant PoE

Mount

Angle Mount Adhesives

(Qty. 2)

micro

1080p Day/Night

IP Security Camera

with Infrared

Model: UVC-G3-MICRO

Screws and Anchors

(Qty. 4)

Cable Clips

(Qty. 8)

Quick Start Guide

Before You Begin

The UVC G3 Micro is designed to work with the UniFi® Video

(v3.8 or above) controller software. The software may be

hosted on either of the following:

• The Ubiquiti Networks® UniFiNVR appliance

• A Linux/Windows computer

Note: The latest UniFi Video software is available for free

download at: www.ubnt.com/download/unifivideo

The UVC G3 Micro can be powered by either of the following

methods:

• Using the included Instant PoE Adapter connected to an

802.3af PoE-compliant switch

• Using the included Power Adapter

Hardware Overview

LED Reset

Magnetic

Base

LED The LED will flash blue during bootup. When the camera

is ready to connect to the Wi-Fi network, the LED pattern

will flash two times accompanied by two beep tones. Once

connected to the network, the LED will glow a breathing

pattern.

State Status

Flashing Blue Device is Booting Up

Steady Blue Connected to NVR

Flashing White Connecting to Wi-Fi

Steady White Ready for Configuration

Flashing Red Cannot Connect to NVR

Steady Red No Wi-Fi Connection

Reset To reset network settings to factory defaults, press and

hold the Reset button until the camera emits two fast tones.

Installation

The UVC G3 Micro can be mounted in four ways:

• Magnetic For temporary installation

• Adhesive For fast, permanent installation

• Screws For secure installation

• Table For installing on a flat surface such as a table or shelf

Magnetic Mount

1. Remove the Wall Mount from the Magnetic Base.

Wall Mount

2. Attach the Power Adapter or Instant PoE Adapter to the

MagneticBase.

3. Attach

the camera and

Magnetic Base directly to a metal

fixture. Go to

Connecting the Power

Adhesive Mount

1. If the Power Adapter cord or PoE Adapter Cord feeds through

the wall, drill or cut a hole and feed the cord through it.

2. Remove the tab from the notch and attach the Wall Mount

using the adhesive side.

*640-00321-01*

640-00321-01

3. Attach the Power Adapter or Instant PoE Adapter to the

MagneticBase.

4. Attach the camera and Magnetic Base to the mount. If

the power cord feeds through the Wall Mount, rotate the

Magnetic Base to align the cord with the notch on the Wall

Mount.Go to Connecting the Power.

Cord on Wall Cord Through Wall Mount

Screw Mount

1. If the circular connector on the Power Adapter or Instant PoE

Adapter needs to connect through the wall, drill or cut a

hole out and feed the power connector through it.

Wall Mount Angle Mount

2. Use the Screws and Screw Anchors to fasten the Wall Mount

or the Angle Mount.

Wall Mount

Angle Mount

3. Attach the Power Adapter to the Magnetic Base.

4. Attach the camera and Magnetic Base to the mount. If

the power cord feeds through the Wall Mount, rotate the

Magnetic Base so the cord aligns with the notch on the Wall

Mount. Go to Connecting the Power.

Cord on Wall Cord Through Wall Mount

Table Mount

1. Feed the circular power connector (on the Power Adapter or

Instant PoE Adapter) through the hole in the Table Stand.

2. Attach the circular power connector to the Magnetic Base

of the camera.

3. Attach the Magnetic Base of the camera to the Table Stand by

pressing it over the two notches and sliding it down.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ubiquiti Caméra de sécurité

Ubiquiti

Ubiquiti UniFi Protect UVC-G3-Flex-3 Manuel utilisateur

Ubiquiti

Ubiquiti UVC-G3-BULLET Manuel utilisateur

Ubiquiti

Ubiquiti UVC--G4--BULLET Manuel utilisateur

Ubiquiti

Ubiquiti UniFi G3 PRO Manuel utilisateur

Ubiquiti

Ubiquiti airCam Manuel utilisateur

Ubiquiti

Ubiquiti UVC-G3-DOME Manuel utilisateur

Ubiquiti

Ubiquiti airCAM DOME Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UVC-G4-PRO Manuel utilisateur

Ubiquiti

Ubiquiti UVC--G4--BULLET Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UVC-G4-PRO Manuel utilisateur

Ubiquiti

Ubiquiti UVC-G3-LED Manuel utilisateur

Ubiquiti

Ubiquiti UniFi Protect Manuel utilisateur

Ubiquiti

Ubiquiti UVC-Dome Manuel utilisateur

Ubiquiti

Ubiquiti UniFi G3 Dome Manuel utilisateur

Ubiquiti

Ubiquiti UVC-G3-AF Manuel utilisateur

Ubiquiti

Ubiquiti UVC-G3-MICRO Manuel utilisateur

Ubiquiti

Ubiquiti airCam MINI Manuel utilisateur

Ubiquiti

Ubiquiti UniFi G3 PRO Manuel utilisateur

Ubiquiti

Ubiquiti airCAM DOME Manuel utilisateur

Ubiquiti

Ubiquiti UniFi UVC-G4-PRO Manuel utilisateur

Ubiquiti

Ubiquiti UVC-G3-DOME-3 Manuel utilisateur

Ubiquiti

Ubiquiti airCam MINI Manuel utilisateur

Ubiquiti

Ubiquiti airCam MINI Manuel utilisateur

Ubiquiti

Ubiquiti airCam Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur