Tymate M12-3 Manuel utilisateur
Tire Pressure Monitoring System
User Manual
Implementation Standard: GB26149-2017
1. Product Overview
1.1 Product Introduction
1.2 Safety Warnings
1.3 Installation Precautions
2. Product Features
3.Product Composition
3.1 Monitor Buttons and LCD Image
3.2 Monitor Installation Instructions
3.3 Turn on/off the Monitor
4. Parameter Settings
4.1 Factory Settings
4.2 Restore Factory Settings
4.3 Setting Order
5. Alarm Status
5.1 High Pressure Alarm
5.2 Low Pressure Alarm
5.3 High Temperature Alarm
5.4 Sudden Air Leak Alarm
5.5 Sensor Low Voltage Alarm
6. Other Functions
6.1 4-7 Tire display
6.2 Power Saving Mode of the Monitor
6.3 Automatically Brightness Adjustment
6.4 Charging of Monitor
6.5 Tire Interchange
7. Recode the Sensor
8. Technical Parameters
9. Disclaimer
10. Some Using Tips
11. Contact Us
01
02
03
04
05
06
07
07
07
07
07
08
08
08
09
10
10
07
08
08
08
09
10
10
07
08
08
08
09
10
1. Product Overview
1-1 Product Introduction
1-2 Safety Warnings
Before installing this product, please read the following precautions.
Thank you for choosing our tire-pressure monitoring system. The system is used to
monitor the air pressure and temperature data of each tire in real time. The collected
pressure and temperature data will be sent to the display by means of radio frequency.
After the data is received and processed by the monitor, it will be displayed on the display
screen to remind users to avoid traffic accidents, and corresponding alarms will be issued
for different abnormal situations according to the standard pressure and temperature
alarm values set by the user.
The system can improve the comfort of the vehicle, reduce fuel consumption and vehicle
wear, improving dynamic performance.
Be sure to read this user manual carefully before installation and keep the manual
for future use. Thank you!
1) The display should be installed in a location where it will not affect the driving vision.
2) The display should be reinforced to avoid falling during driving.
3) During driving, if the tire temperature rises sharply, the tire pressure will also rise
accordingly. If the temperature exceeds the warning value, stop the car to let it dissipate
heat naturally to prevent brake failure or tire blowouts.
4) If the pressure continues to rise or drop at an accelerated rate while driving, stop to
check for leaks or other problems.
5) When the air pressure is too high, you should be aware of a tire blowout. When the air
pressure is too low, pay attention to fuel consumption and balance.
6) This product can effectively monitor the tire pressure and temperature in real time, but
cannot avoid all traffic accidents or tire blowouts. Using high-quality tires is as important
as this product to ensure that the tire pressure is normal.
7) This product will automatically detect the tires and sound an alarm in case of abnormal
situations, so that the driver does not need to pay frequent attention to it so as not to be
distracted when driving.
1.3 Installation Precautions
1) If the monitor does not feel vibration within 10 minutes, the monitor will automatically
enter the sleep mode. If there is a slight vibration, it will automatically turn on and receive
the data sent by the sensor. If no data is displayed on the screen, it does not mean that
the product is abnormal. When the pressure value changes, it will update the data again.
2) There is a wireless connection between the sensor and the monitor. And the
transmission distance of them is far enough. Designed with multiple anti-interference
functions, the possibility of interference to the sensor and the monitor is extremely low.
3) During the driving process, due to the thermal expansion and contraction of the air, the
tire pressure and temperature will get higher or lower, which is normal.
4) In general, tires have normal natural air leaks. The tire pressure will decrease over
time, which is a normal phenomenon and has no direct relationship with the installation of
this product.
5) If you have any other problems with installation, please contact us.
6) If you have any problems with installation, please contact the agent or distributor.
2. Product Features
Auto-sensing solar charging
Excessive pressure and temperature alarm
Visual & audible alarm
Multiple pressure unit options (PSI, BAR)
Multiple temperature unit options (℃, ℉)
The user can set standard alarm values for the tire pressure and temperature
Arbitrary interchangeability of tire positions
The monitor can automatically turn on the display backlight
The monitor comes with a rechargeable battery
Support up to seven tires (spare tires)
The display shows the pressure and temperature of the four tires at the same time
Sudden air leak alarm
3.1 Monitor Buttons and LCD Image
3.2 Monitor Installation Instructions
Install the monitor in a place where it is easy to see in the car. The user can directly stick
the display on the dashboard with sticky pad, and then use the DC-DC power adaptor to
connect the monitor to the cigarette lighter in the car for charging (please charge it for at
least 2.5 hours for the first time).
3. Product Composition
ON/OFF/-SET
Pressure unit: BAR or PSI, for users to choose
Temperature unit: °C or °F, for users to choose
Solar panels USB charging socket
Description
Tires
Sensor low battery alarm
Display battery level indicator
Fault icon
Solar charging icon
Icon
3.3 Turn on/off the Monitor
4.1 Factory Settings
4.2 Restore Factory Settings
When parking for a long time, the user can manually turn off/on the display. In the off state,
press and hold the "-" key, the monitor turns on after a beep sound. In the power-on state,
press and hold the "-" key, the monitor turns off after a beep sound. When the battery is
low, the display will automatically turn off.
In the standby mode, press and hold the "SET" button on the display, release after the
first beep sound, the display will enter the first setting interface. When the corresponding
LCD symbol flashes, you can select the parameter item by pressing the "SET" key. Press
"-" or "+" to set specific parameter values. After the setting is completed, press and hold
the "SET" button and release after you hear a beep sound. In this way you can save the
parameters and exit to the normal standby state. When entering the setting state, press
"SET”and "+" at the same time to exit the setting mode without saving the setting data. If
there is no operation within 1 minute in the setting state, the system will automatically exit
the setting mode and return to the normal standby state.
Turn off the display first, then press and hold the "-" button to turn it on. Then the
full-screen display page appears. Press and hold the "SET" button within 3 seconds and
release after you hear a beep sound, indicating that the factory settings are restored
successfully.
4. Parameter Settings
Pressure unit BAR/PSI
Low pressure alarm value
Temperature unit
High temperature alarm value158
oF
oF
High voltage alarm value
4.3 Setting Order
1）Pressure Unit setting
When the "PSI" or "BAR" icon flashes,
press the "-" or "+" key to select the "PSI" or "BAR" required by the user.
2）Temperature Unit setting
When the “
” or “
” icon flashes,
press the “-” or “+” key to select the “ ” or “ ” required by the user.
3）Front tire high pressure alarm value setting ( )
When the high pressure parameter and the front tire rim mark flash,
press the "-" or "+" key to set the high pressure alarm value required by the user.
4) Front tire low pressure alarm value setting ( )
When the low pressure parameter and the front tire icon is flashing,
press the "-" or "+" key to set the low pressure alarm value required by the user.
5) Rear tire high pressure alarm value setting ( )
When the high pressure parameter and rear tire icon is flashing,
press the "-" or "+" key to set the high pressure alarm value required by the user.
6) Rear tire low pressure alarm value setting ( )
When the low pressure parameter and rear tire icon is flashing,
press the "-" or "+" key to set the low pressure alarm value required by the user.
7) Spare tire high pressure alarm value setting ( )
When the high pressure parameter and the spare tire icon is flashing,
press the "-" or "+" key to set the high pressure alarm value required by the user.
8) Spare tire low pressure alarm value setting ( )
When the low pressure parameter and the spare tire icon is flashing,
press the"-"or" + "key to set the low pressure alarm value required by the user.
9）High temperature alarm value setting ( )
When the high temperature parameter is flashing,
press the"-"or" + "key to set the high temperature alarm value required by the user.
5.1 High Pressure Alarm
For example: when the front left tire pressure value is 3.1BAR, the display shows the
picture below with a warning sound (Bi...Bi... Bi...).
5.2 Low Pressure Alarm
For example: when the front left tire pressure value is 1.9BAR, the display shows the
picture below with a warning sound (Bi...Bi... Bi...).
5.3 High Temperature Alarm
For example: when the temperature of the front left tire is 71 , the display shows the
picture below with a warning sound (Bi...Bi... Bi...).
High pressure / low pressure / high temperature / sudden air leak / low voltage alarm of
sensor battery
The same interface of the display shows the pressure and temperature of 4 tires. When
the tire pressure or temperature exceeds the safety range set by the user, corresponding
tire icon, parameter and corresponding fault icon on the display screen will flash and
alarm sound will prompt. Press any key to cancel the alarm sound but the corresponding
tire icon, parameter and corresponding fault icon will continue flashing until all tire faults
are resolved.
5. Alarm Status
oC
5.4 Sudden Air Leak Alarm
When the sensor detects a sudden air leak, it will immediately send alarm data to the
display. The corresponding tire icon, air pressure reading and fault icon alarm on the
display will sound (Bi......). Press any key to cancel the alarm prompt. If the sensor
continues to send leak information, it will prompt a leak alarm again.
For example: when the pressure of the left front tire drops directly from the normal
pressure of 2.5BAR to 2.2BAR, a sudden air leak alarm shows the picture below.
5.5 Sensor Low Voltage Alarm
When the sensor detects low voltage, it will immediately send alarm data to the display.
The corresponding tire icon, low voltage icon, and alarm sound (Bi...Bi... Bi...) prompt on
the display. Press any key to cancel only the alarm sounds, but the low voltage icon and
tire icon will still flash until the faulty sensor is replaced with a new battery or re-matched
with a new sensor.
For example: when the sensor voltage of the right rear tire is too low, it shows the picture
below.
Table des matières
Autres manuels Tymate Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur