Tyco TY-B Series Manuel utilisateur

Series TY-B — 80 and 115 K-factor

Conventional Sprinklers

Special Response, Standard Coverage

Worldwide

Contacts

www.tyco-ﬁre.com

Page 1 of 4 FEBRUARY 2015 TFP663

IMPORTANT

Always refer to Technical Data

Sheet TFP700 for the “INSTALLER

WARNING” that provides cautions

with respect to handling and instal-

lation of sprinkler systems and com-

ponents. Improper handling and

installation can permanently damage

a sprinkler system or its compo-

nents and cause the sprinkler to fail

to operate in a ﬁre situation or cause

it to operate prematurely.

General

Description

The Series TY-B, 80 and 115 K-factor,

Conventional Sprinklers described in

this data sheet are special response -

standard coverage, decorative 4 mm

glass bulb sprinklers designed for use

in accordance with the installation rules

recognized by the applicable Approval

agency (e.g., VdS). These sprinklers are

intended to be installed either pendent

or upright, and in either position, they

produce a spherical water discharge

pattern with approximately 50% of

the discharge directed upwards and

approximately 50% of the discharge

directed downwards.

NOTICE

The Series TY-B Sprinklers described

herein must be installed and maintained

in compliance with this document, as

well as with the applicable standards

recognized by the Approval agency, in

addition to the standards of any other

authorities having jurisdiction. Failure

to do so may impair the performance

of these devices.

The owner is responsible for maintain-

ing their ﬁre protection system and

devices in proper operating condi-

tion. Contact the installing contrac-

tor or product manufacturer with any

questions.

Sprinkler

Identiﬁcation

Numbers (SINs)

TY3641 – Conventional 80K

TY4641 – Conventional 115K

Technical

Data

Approvals

VdS Approved (CEA 4001)

Maximum Working Pressure

12,1 bar

Discharge Coefﬁcient

K = 80 lpm/bar1/2

K = 115 lpm/bar1/2

Temperature Ratings

57°C, 68°C, 79°C, 93°C, and 141°C

Finishes

Refer to Table A.

Physical Characteristics

Frame ............................Bronze

Button...................... Brass/Copper

Sealing Assembly . . . . . . . . . . . . . . . . Beryllium

Nickel w/TEFLON

Bulb .............................. Glass

Compression Screw . . . . . . . . . . . . . . . . Bronze

Deector..........................Copper

Operation

The glass bulb contains a uid which

expands when exposed to heat. When

the rated temperature is reached, the

uid expands sufciently to shatter the

glass bulb, allowing the sprinkler to acti-

vate and water to ow.

Installation

The Series TY-B Sprinklers must

be installed in accordance with this

section.

General Instructions

Do not install any bulb type sprinkler

if the bulb is cracked or there is a loss

of liquid from the bulb. With the sprin-

kler held horizontally, a small air bubble

should be present. The diameter of the

air bubble is approximately 1,6 mm for

the 57°C to 2,4 mm for the 141°C tem-

perature ratings.

A leak tight 1/2 inch NPT sprinkler joint

should be obtained with a torque of

9 to 19 Nm. A leak tight 3/4 inch NPT

sprinkler joint should be obtained with

a torque of 13 to 27 Nm. Higher levels

of torque may distort the sprinkler inlet

and cause leakage or impairment of the

sprinkler.

TFP663

Page 2 of 4

Do not attempt to make up for insuf-

cient adjustment in the escutcheon

plate by under- or over-tightening the

sprinkler. Readjust the position of the

sprinkler tting to suit.

The Series TY-B Conventional Sprin-

klers must be installed in accordance

with the following instructions.

Step 1. With pipe thread sealant

applied to the pipe threads, hand

tighten the sprinkler into the sprinkler

tting.

Step 2. Tighten the sprinkler into the

sprinkler tting using only the W-Type

6 Sprinkler Wrench (Ref. Figure 2)

or W-Type 7 Sprinkler Wrench (Ref.

Figure 3). With reference to Figure 1, the

W-Type 6 or W-Type 7 Sprinkler Wrench

is to be applied to the wrench ats.

Care and

Maintenance

The Series TY-B Sprinklers must be

maintained and serviced in accordance

with this section.

Before closing a re protection system

main control valve for maintenance

work on the re protection system that

it controls, permission to shut down the

affected re protection system must be

obtained from the proper authorities

and all personnel who may be affected

by this action must be notied.

Sprinklers that are found to be leaking

or exhibiting visible signs of corrosion

must be replaced.

Automatic sprinklers must never be

painted, plated, coated or other-

wise altered after leaving the factory.

Modied sprinklers must be replaced.

Sprinklers that have been exposed to

corrosive products of combustion, but

have not operated, should be replaced

if they cannot be completely cleaned

by wiping the sprinkler with a cloth or

by brushing it with a soft bristle brush.

Care must be exercised to avoid

damage to the sprinklers before,

during, and after installation. Sprin-

klers damaged by dropping, striking,

wrench twist/slippage, or the like, must

be replaced. Also, replace any sprin-

kler that has a cracked bulb or that has

lost liquid from its bulb. (Ref. Installa-

tion Section).

The owner is responsible for the inspec-

tion, testing, and maintenance of their

re protection system and devices in

compliance with this document, as well

as with the applicable standards of the

National Fire Protection Association

(e.g., NFPA 25), in addition to the stan-

dards of any other authorities having

jurisdiction. Contact the installing con-

tractor or product manufacturer with

any questions.

It is recommended that automatic

sprinkler systems be inspected, tested,

and maintained by a qualied Inspec

tion Service in accordance with local

requirements and/or national codes.

****

SHOWN

PENDENT

SHOWN

PENDENT

CROSS SECTION

SHOWN UPRIGHT

CROSS SECTION

SHOWN UPRIGHT

Bulb

Button

Frame

-4-

Deector6 -

Components:

56 mm

57 mm

38 mm38 mm

11 mm

NOMINAL

MAKE-IN

** Pipe thread connections per

ISO 7-1 can be provided on

special request.

Temperature rating is

indicated on Deector

or adjacent to orice

seat on Frame.

WRENCH

FLATS

WRENCH

FLATS

Sealing

Assembly

Compression

Screw

1/2"

NPT

3/4"

NPT

13 mm

NOMINAL

MAKE-IN

WRENCH RECESS

(END "A" USED FOR

1/2" NPT MODELS)

WRENCH RECESS

(END "B" USED FOR

3/4" NPT MODELS)

WRENCH

RECESS

PUSH WRENCH

IN TO ENSURE

ENGAGEMENT

WITH SPRINKLER

WRENCHING AREA

FIGURE 1

SPECIAL RESPONSE SERIES TY-B CONVENTIONAL SPRINKLERS

FIGURE 2

W-TYPE 6

SPRINKLER WRENCH

FIGURE 3

W-TYPE 7

SPRINKLER WRENCH

TFP663

Page 3 of 4

Limited

Warranty

For warranty terms and conditions, visit

www.tyco-re.com.

Ordering

Procedure

Contact your local distributor for avail-

ability. When placing an order, indicate

the full product name and Part Number

(P/N).

Sprinkler Assembly

Specify: (Specify SIN), Series Special

Response TY-B Conventional Sprinkler,

(specify) K-factor, (specify) temperature

rating, (specify) nish, P/N (specify from

Table A)

Sprinkler Wrench

Specify: W-Type 6 Sprinkler Wrench,

P/N 56-000-6-387

Specify: W-Type 7 Sprinkler Wrench,

P/N 56-850-4-001

* Eastern Hemisphere sales only

P/N 57 - XXX - X - XXX

SIN

473 80K CONVENTIONAL (1/2” NPT) TY3641

493 115K CONVENTIONAL (3/4” NPT) T Y46 41

SPRINKLER

FINISH

1NATURAL BRASS

3PURE WHITE (RAL9010)*

POLYESTER

4SIGNAL WHITE (RAL9003)

POLYESTER

9CHROME PLATED

TEMPERATURE

RATING

135 57°C

155 68°C

175 79°C

200 93°C

286 141°C

TABLE A

SERIES TY-B SPECIAL RESPONSE CONVENTIONAL SPRINKLERS

PART NUMBER SELECTION

GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

TFP663

Page 4 of 4

TEFLON is trademark of The DuPont Corporation.

Autres manuels pour TY-B Series

Autres manuels Tyco Système d'irrigation

Tyco

Tyco TY-FRB Series Manuel utilisateur

Tyco

Tyco RFII Series Manuel utilisateur

Tyco

Tyco DS-1 Series Manuel utilisateur

Tyco

Tyco DS-1 Series Manuel utilisateur

Tyco

Tyco WS TY3388 Manuel utilisateur

Tyco

Tyco DS-1 Series Manuel utilisateur

Tyco

Tyco Issue D Quartzoid TY3191 Manuel utilisateur

Tyco

Tyco ELO-231B Series Manuel utilisateur

Tyco

Tyco ESFR-25 Manuel utilisateur

Tyco

Tyco LFII Series Manuel utilisateur

Tyco

Tyco RFII-MRI Series Manuel utilisateur

Tyco

Tyco DS-2 Series Manuel utilisateur

Tyco

Tyco Rapidresponse LFII Series Manuel utilisateur

Tyco

Tyco AQUAMIST ULF AM27 Manuel utilisateur

Tyco

Tyco RAPID RESPONSE Series Manuel utilisateur

Tyco

Tyco ESFR-22 Manuel utilisateur

Tyco

Tyco Integra Ci1 Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Tyco

Tyco CCU Rack Guide d'installation

Tyco

Tyco rapidresponse RSV-1 Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Tyco

Tyco TY-B Series Manuel utilisateur

Tyco

Tyco TY-B Series Manuel utilisateur

Tyco

Tyco F690 Manuel utilisateur

Manuels Système d'irrigation populaires d'autres marques

Hunter

Hunter Institutional Series Manuel utilisateur

Cellfast

Cellfast 52-305 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manuel utilisateur

Tyco Fire Product

Tyco Fire Product CENTRAL A Manuel utilisateur

Oral Care Technologies

Oral Care Technologies Hydro Floss Manuel utilisateur

Reliable

Reliable F1-300 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Gem F892 Manuel utilisateur

Netafim

Netafim NETBEAT Manuel utilisateur

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manuel utilisateur

Reliable

Reliable F4FR Manuel utilisateur

OpenSprinkler

OpenSprinkler OSPi Manuel utilisateur

EINHELL

EINHELL GE-WW 5537 E Manuel utilisateur

Valley

Valley Bender160 Manuel utilisateur

Reliable

Reliable F1FR42 Series Manuel utilisateur

Reliable

Reliable F1FR-300 Manuel utilisateur

Toro

Toro 730 Series Guide rapide

Eden

Eden 97063-EDAMZ Manuel utilisateur

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Manuel utilisateur