Tyco ESFR-17 Manuel utilisateur

Page 1 of 4 NOVEMBER 2021 TFP784

Worldwide

Contacts

www.tyco-ﬁre.com

IMPORTANT

Refer to Technical Data Sheet

TFP2300 for warnings pertaining to

regulatory and health information.

Always refer to Technical Data

Sheet TFP700 for the “INSTALLER

WARNING” that provides cautions

with respect to handling and instal-

lation of sprinkler systems and com-

ponents. Improper handling and

installation can permanently damage

a sprinkler system or its compo-

nents and cause the sprinkler to fail

to operate in a ﬁre situation or cause

it to operate prematurely.

Scan the QR code or enter the URL

in a web browser to access the most

up-to-date electronic version of this

document. Data rates may apply.

https://docs.jci.com/tycoﬁre/

esfr-pendent-sprinkler-accessories

ESFR Pendent Sprinkler

Accessories

General

Description

The TYCO Model ES-1 and ES-2 Sprin-

kler Shields and Model EG-25 Sprin-

kler Guard are designed for use with

the TYCO Model ESFR Pendent Sprin-

kler range. The sprinkler shield and

guard assemblies are for sprinkler

installation locations susceptible to

mechanical or physical damage.

The sprinkler guard and shield applica-

tions are as follows:

• Pendent ESFR sprinklers located in

areas not susceptible to the threat of

mechanical or physical damage can

be equipped with Model ES-1 and

ES-2 Sprinkler Shields for protection

from water spray of higher elevation

sprinklers. See Table A for sprinkler

applications.

• The Model EG-25 Sprinkler Guard,

shown in Figure 2, provides protec-

tion for TYCO Model ESFR-22 and

ESFR-25 Pendent Sprinklers from

mechanical and/or physical damage,

for example, rack storage sprinkler

installations.

The Models ES-1 and ES-2 Sprinkler

Shields and Model EG-25 Sprinkler

Guard are intended for use in ﬁre sprin-

kler systems designed in accordance

with the standard installation rules

recognized by the applicable Listing

agency.

NOTICE

The Models ES-1 and ES-2 Sprin-

kler Shields and Model EG-25 Sprin-

kler Guard described herein must be

installed and maintained in compli-

ance with this document and with the

applicable standards of the NATIONAL

FIRE PROTECTION ASSOCIATION

(NFPA), in addition to the standards

of any Authorities Having Jurisdiction.

Failure to do so may impair the perfor-

mance of these devices.

Owners are responsible for maintaining

their ﬁre protection system and devices

in proper operating condition. The

installing contractor or sprinkler man-

ufacturer should be contacted with any

questions.

Technical

Data

Approvals

FM Approved

Finishes

Red painted, zinc coating and zinc chromate

Physical Characteristics

Models ES-1 and ES-2 Sprinkler Shields:

• Stamped and formed carbon steel sheet

Model EG-25 Sprinkler Guard:

• Welded assembly fabricated from carbon

steel

Design

Criteria

In accordance with the requirements of

the NFPA, sprinkler shields and guards

shall be Listed. Sprinkler shields and

guards are only Listed for use with

sprinklers speciﬁed in Table A.

TFP784

Page 2 of 4

Installation

The TYCO Model ES-1 and ES-2 Sprin-

kler Shields and Model EG-25 Sprinkler

Guard must be installed onto TYCO

ESFR Sprinklers in accordance with

this section.

Installing the Model ES-1 and ES-2

Sprinkler Shield

Note: TYCO ESFR Sprinklers must

be installed in accordance with their

respective Technical Data Sheet, see

Table A.

See Figure 1 for sprinkler shield fea-

tures, dimensions and installation

details.

Step A. With the stamped markings

facing toward the deﬂector, thread the

Shield onto the sprinkler threads to the

end nearest the frame arms.

Step B. Install the sprinkler into the

sprinkler fitting in accordance with

the applicable sprinkler technical data

sheet, see Table A.

Step C. Rotate the Shield clockwise

until ﬂush against the face of the sprin-

kler ﬁtting.

ESFR

Sprinkler Shield

Model Guard

Model

Model SIN K-Factor

gpm/psi½

(Lpm/bar½)

Thread Size

in. NPT

Technical

Data

Sheet ES-1 ES-2 EG-25

ESFR-14 TY6236 14.0

(201,6)

3/4

TFP319 1

ESFR-17 TY7223 16.8

(241,9) TFP317 1

ESFR-17 TY7236 16.8

(241,9) TFP322 1

ESFR-22 TY8223 22.4

(320) 1

TFP321 1 2

ESFR-25 TY9226 25.2

(362,9) TFP312 1 1

NOTES

1. FM Approved

2. Compatible but not Listed or Approved

Shield

Model

Diameter

in.

(mm)

Thread

Size

in. NPT

ES-1 3.50

(88,9) 3/4

ES-2 4.00

(101,6) 1

GUARD

BASE

PLATE

GUARD

BAR

TYCO MODEL

ESFR-22 OR ESFR-25

SPRINKLER

NOT INCLUDED

GUARD CLIP

ENGAGED

AGAINST GUARD

BASE PLATES

SPRINKLER

THREAD RELIEF

ENGAGED BY GUARD

BASE PLATES

MODEL EG-25

GUARD

(103 mm)

3-5/8" DIA.

(92 mm)

SHIELD

SPRINKLER

FITTING

FIGURE 2

MODEL EG-25 SPRINKLER GUARD

FEATURES AND DIMENSIONS

FIGURE 1

MODEL ES-1 AND ES-2 SPRINKLER SHIELD

FEATURES AND DIMENSIONS

TABLE A

SPRINKLER SHIELD AND GUARD APPLICATIONS

LABORATORY LISTINGS AND APPROVALS

TFP784

Page 3 of 4

Step 4. Swivel the second clip to

engage the open end onto the oppos-

ing bar and slide toward the base

plates until fully seated against the

base plates.

Note: The Installation Tool shown in

Figure 2 may be used as an aid when

sliding and seating the clips. Pliers may

be used in addition to the Installation

Tool to facilitate seating the clips.

NOTICE

To complete the installation, the clips

must seat against the base to be fully

seated.

Installing the Model EG-25

Sprinkler Guard

Note: The Model ESFR-22 Sprinkler

must be installed in accordance with

Technical Data Sheet TFP321 and

Model ESFR-25 Sprinkler must be

installed in accordance with Technical

Data Sheet TFP312 before installing the

Model EG-25 Sprinkler Guard.

See Figure 2 for guard features and

dimensions and Figure 3 for installa-

tion details.

Step 1. With the clips loose, care-

fully spread the two halves of

the sprinkler guard apart so

the bars pass by the sprinkler

deﬂector and the base plates pass by

the sprinkler thread relief from the side.

Step 2. Position the guard on center

relative to the sprinkler, engaging the

base plates evenly onto the sprinkler

thread relief. Align the guard base plate

gaps parallel with the sprinkler frame

arms.

Step 3. Swivel the ﬁrst clip to engage

the open end onto the opposing bar

and slide toward the base plates until

fully seated against the base plates

TYCO

MODEL

ESFR-22

OR ESFR-25

PENDENT

SPRINKLER

SWIVEL CLIPS OVER OPPOSING

BARS AND SLIDE TOWARD BASE

PLATES UNTIL SNUG

OPPOSING

BAR

BASE

PLATES

BASE

PLATES

BASE

PLATES

BASE

PLATES

FIRST

CLIP FULLY

ENGAGED

INSTALLATION TOOL

(SHIPPED WITH

GUARDS)

BAR

SLOT

INSTALLATION

TOOL

A PLIER

MAY BE

USED

SECOND

CLIP FULLY

ENGAGED

WITH INSTALLATION TOOL APPLIED OVER

OPPOSING BARS, PRESS SECOND CLIP

TOWARD BASE PLATES UNTIL FULLY ENGAGED

INSTALLATION

TOOL

MODEL

EG-25 GUARD

SECOND

CLIP

WITH SPRINKLER PROPERLY INSTALLED

AND LINK PROTECTOR REMOVED,

CAREFULLY SPREAD GUARD BASE PLATES

APART AND FIT ONTO SPRINKLER,

ENGAGING INNER EDGES OF

BASE PLATES INTO SPRINKLER

THREAD RELIEF

FIGURE 3

MODEL EG-25 SPRINKLER GUARD

INSTALLATION

TFP784

Page 4 of 4

NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association

1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

Care and

Maintenance

The TYCO Model ES-1 and ES-2 Sprin-

kler Shields and Model EG-25 Sprin-

kler Guard do not require any regularly

scheduled maintenance; however,

proper installation of the sprinkler

shield or guard should be verified

during the annual visual inspection of

the sprinkler.

NOTICE

Before closing a ﬁre protection system

main control valve for maintenance

work on the fire protection system

that it controls, obtain permission to

shut down the affected ﬁre protec-

tion system from the proper authori-

ties and notify all personnel who may

be affected by this action.

Sprinkler shields and guards found to

be damaged or visibly deformed must

be replaced.

Responsibility lies with sprinkler

owners for the inspection, testing,

and maintenance of their ﬁre protec-

tion system and devices in compliance

with this document, as well as with

the applicable standards of the NFPA

(for example, NFPA 25), in addition to

the standards of any other authorities

having jurisdiction. Contact the install-

ing contractor or sprinkler manufac-

turer regarding any questions.

Automatic sprinkler systems are rec-

ommended to be inspected, tested,

and maintained by a qualiﬁed Inspec-

tion Service in accordance with local

requirements and/or national codes.

Owners must assure that the sprinklers

are not used for the hanging of any

objects and are only cleaned by means

of gently dusting with a feather-duster.

Otherwise, non-operation in the event of

a ﬁre or inadvertent operation may

result.

Limited

Warranty

For warranty terms and conditions, visit

www.tyco-ﬁre.com.

Ordering

Procedure

Contact your local distributor for avail-

ability. When placing an order, indicate

the full product name and Part Number

(P/N).

Model ES-1 and ES-2

Sprinkler Shields

Specify: Model (specify ES-1 or ES-2)

Sprinkler Shield, (specify ﬁnish), P/N

(specify):

ES -1

Red Painted ..................58-000-1-003

Zinc Coating..................58-000-1-002

ES-2

Red Painted ..................58-000-1-006

Zinc Coating..................58-000-1-005

Model EG-25 Sprinkler Guard

Specify: Model EG-25 Sprinkler Guard,

(specify ﬁnish), P/N (specify):

Red Painted ..................56-939-1-025

Zinc Chromate ............... 56-939-9-025

Additional Guard Installation Tools

Specify: Guard Installation Tool, P/N

56-000-8-597

Note: The Model EG-25 Sprinkler

Guard Installation Tool is included with

orders in original carton quantities.

Autres manuels pour ESFR-17

Ce manuel convient aux modèles suivants

Autres manuels Tyco Système d'irrigation

Tyco

Tyco Grinnell F692 DESIGNER Manuel utilisateur

Tyco

Tyco TY-FRL Series Manuel utilisateur

Tyco

Tyco EC-11 Series Manuel utilisateur

Tyco

Tyco LFII Series Mode d’emploi

Tyco

Tyco ESFR-14 Manuel utilisateur

Tyco

Tyco TFP PH2 Manuel utilisateur

Tyco

Tyco Rapidresponse LFII Series Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Tyco

Tyco LD Manuel utilisateur

Tyco

Tyco Rapidresponse LFII Series Manuel utilisateur

Tyco

Tyco RFII Manuel utilisateur

Tyco

Tyco rapid response LFII Series Manuel utilisateur

Tyco

Tyco rapid response LFII Series Manuel utilisateur

Tyco

Tyco D Quartzoid TY3191 Manuel utilisateur

Tyco

Tyco TY-FRB Series Manuel utilisateur

Tyco

Tyco LFII Series Manuel utilisateur

Tyco

Tyco ESFR-34 Manuel utilisateur

Tyco

Tyco ESFR-17 Manuel utilisateur

Tyco

Tyco SW-20 Manuel utilisateur

Tyco

Tyco DSB-2 Manuel utilisateur

Tyco

Tyco TY-B Series Manuel utilisateur

Tyco

Tyco TY5332 Manuel utilisateur

Tyco

Tyco ESFR-22 Manuel utilisateur

Tyco

Tyco TY-B Series Manuel utilisateur

Manuels Système d'irrigation populaires d'autres marques

Hunter

Hunter Institutional Series Manuel utilisateur

Cellfast

Cellfast 52-305 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manuel utilisateur

Tyco Fire Product

Tyco Fire Product CENTRAL A Manuel utilisateur

Oral Care Technologies

Oral Care Technologies Hydro Floss Manuel utilisateur

Reliable

Reliable F1-300 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Gem F892 Manuel utilisateur

Netafim

Netafim NETBEAT Manuel utilisateur

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manuel utilisateur

Reliable

Reliable F4FR Manuel utilisateur

OpenSprinkler

OpenSprinkler OSPi Manuel utilisateur

EINHELL

EINHELL GE-WW 5537 E Manuel utilisateur

Valley

Valley Bender160 Manuel utilisateur

Reliable

Reliable F1FR42 Series Manuel utilisateur

Reliable

Reliable F1FR-300 Manuel utilisateur

Toro

Toro 730 Series Guide rapide

Eden

Eden 97063-EDAMZ Manuel utilisateur

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Manuel utilisateur