Tyco Electronics PRO-CRIMPER III 58603-1 Manuel utilisateur

Instruction Sheet

PRO-CRIMPER* III Hand Crimping

Tool Assembly 58603-1 with 408-4342

L C B

of 5

2009 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. ther products, logos, and company names used are the property of their respective owners.

T LING ASSISTANCE CENTER 1-800-722-1111

PR DUCT INF RMATI N1-800-522-6752 This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at

www.tycoelectronics.com

21 MAY 09 Rev A

Die Assembly 58603-2

PROPER USE GUIDELINES

CumulativeTraumaDisorderscanresultfromtheprolongeduseof manuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

The PR -CRIMPER III Hand Crimping Tool is a Commercial" grade tool

and is designed primarily for field installation, repair, maintenance work, or

prototyping in industrial, commercial, or institutional applications. Product

crimped with this tool will meet the crimp height requirement for hand tools in the

appropriate 114 application specification, but may not comply with other feature

parameters of the specification. Tyco Electronics offers a variety of tools to

satisfy your performance requirements. For additional information, contact the

Tooling Assistance Center at 1-800-722-1111.

Locator Assembly

(Supplied with

Die Assembly)

Front of Tool

(Locator Side)

Die Assembly

Moving Jaw

Ratchet Adjustment Wheel

Moving Handle

Stationary Handle

PR -CRIMPER III Hand

Crimping Tool Frame

354940-1 (408-9930)

Pivot Pin

Back of Tool

(Wire Side)

Stationary Jaw

Tool Marking (1)

ire

TE Die Assembly TE Locator Assembly

{

Contact FamilY

}

Size (mm2)

(Color)

Insul Dia

(mm [in.])

Strip Length

(mm [in.])

2.5

(Yellow)

58603 2

58516 1

Junior Power

Timer and

1.5

(Blue) 1.4-2.1 3.1-3.9

58603

58516

Timer and

2.8mm Tab 1.0

(Red)

[.055-.083] [.122-.154]

0.75

(Green)

{

Supplied with die assembly, also available separately.

}

Contact the Tooling Assistance Center or the Product Information Center at the numbers listed below for specific contact part numbers.

Figure 1

1. INTRODUCTION

PRO–CRIMPER III Hand Crimping Tool Assembly

58603–1 consists of Die Assembly 58603–2 and

PRO–CRIMPER III Hand Tool Frame 354940–1. The

die assembly consists of crimping dies and a locator

assembly.

Read these instructions thoroughly before crimping

any contacts.

Dimensions on this sheet are in millimeters [with

inch equivalents provided in brackets]. Figures

and illustrations are for identification only and are

not drawn to scale.

Reason for revision can be found in Section 11,

REVISION SUMMARY.

NOTE

408-4342

PRO-CRIMPER III Han Crimping Tool Assembly 58603-1

Rev

of 5 Tyco Electro ics Corporatio

Figure 2

Nut

Locator

Assembly Tool Frame

Die Retai i g Pi s

Lo g Die Retai i g

Screw

Chamfer

I sulatio A vil

Wire A vil

Offset

Wire Crimper

Chamfer I sulatio

Crimper

Short Die Retai i g

Screw

2. DESCRIPTION

(Figures 1 a d 2)

The tool features a tool frame with a stationary jaw

and handle, a moving jaw, a moving handle, and an

adjustable ratchet that ensures full contact crimping.

The tool frame holds a die assembly with four

crimping sections.

The die assembly features a wire anvil, an insulation

anvil, a wire crimper, and an insulation crimper.

Attached to the outside of the tool frame is a locator

assembly, which contains a locator, a spring retainer,

and a contact support.

Die retaining pins and die retaining screws are used

to position and secure the dies in the tool frame. A

nut is used on the long die retaining screw to hold the

locator assembly in place.

3. INSTALLATION AND REMOVAL OF DIE SET

AND LOCATOR ASSEMBLY

(Figure 2)

1. Open the tool handles and remove the two die

retaining screws from the tool jaws.

2. Place the wire anvil and insulation anvil so that

their chamfered sides and their marked surfaces

face outward, when mounted in the moving jaw of

the tool frame.

3. Insert the two die retaining pins.

4. Insert the short die retaining screw through the

jaw and through both anvil dies, and tighten the

screw just enough to hold the dies in place. Do

not

tighten the screw completely at this time.

5. Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

6. Insert the two die retaining pins.

7. Insert the long die retaining screw through the

jaw and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do

not

tighten the screw completely at this time.

8. Carefully close the tool handles, making sure

that the anvils and crimpers align properly.

Continue closing the tool handles until the ratchet

in the tool frame has engaged sufficiently to hold

the anvils and crimpers in place, then tighten both

die retaining screws.

9. Place the locator assembly over the end of the

long die retaining screw, and position the locator

assembly against the side of the tool jaw.

10. Place the nut onto the end of the long screw

and tighten the nut enough to hold the locator

assembly in place, while still allowing the locator to

slide up and down.

11. To disassemble, close the tool handles until the

ratchet releases, remove the nut, locator assembly,

the two die retaining screws, and the four die

retaining pins, and slide the anvils and crimpers out

of the tool jaws.

408-4342

PRO-CRIMPER III Hand Crimping Tool Ass mbly 58603-1

of 5Rev

Tyco Electronics Cor oration

4. CONTACT SUPPORT ADJUSTMENT

(Figure 3)

The contact support s preset pr or to sh pment,

but m nor adjustment may be necessary.

1. Make a sample crimp and determine if the

contact is straight, bending upward, or bending

downward.

2. If adjustment is required, loosen the screw that

holds the contact support onto the locator

assembly.

The ratchet has detents that create aud ble cl cks

as the tool handles are closed.

3. Place a contact with wire into the proper nest

and close the tool handles until the ratchet reaches

the sixth click, or until the contact support touches

the contact.

4. Slightly loosen the nut that holds the locator

assembly onto the tool frame.

5. Move the contact support as required to

eliminate the bending of the contact.

6. Tighten the nut and close the handles until the

ratchet releases.

7. Remove and inspect the contact.

8. Make another sample crimp. If the contact is

straight, tighten the contact support screw. If the

contact is still being bent during crimping, repeat

the adjustment procedure.

5. CRIMPING PROCEDURE

Th s tool s prov ded w th a cr mp adjustment

feature. Int ally, the cr mp he ght should be

ver f ed as specf ed n Fgure 4. Refer to Sect on

6, CRIMP HEIGHT INSPECTION, and Sect on 7,

CRIMP HEIGHT ADJUSTMENT, to ver fy crmp

he ght before us ng the tool to crmp des red

contacts.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the wire

to the length indicated in Figure 1, taking care not to

nick or cut wire strands. Select an applicable contact

and identify the appropriate crimp section according

to the wire size markings on the tool. Refer to

Figure 3 and proceed as follows:

1. Hold the tool so that the back (wire side) is

facing you. Squeeze tool handles together and

allow them to open fully.

2. Holding the contact by the mating end, insert the

contact—insulation barrel first—through the front of

the tool and into the appropriate crimp section.

Figure 3

Adjustment

Screw for

Contact

Su ort

Contact

Su ort Locator

Back of Tool

(Wire Side)

Wire

Contact

(Ty ) Stri Length

Wire Inserted

to Sto

Locator in Wire

Sto Slot

Not :

Not to Scale

NOTE

408-4342

PRO-CRIMPER III Hand Crimping Tool Assembly 58603-1

Rev

of 5 Ty o Ele troni s Corporation

3. Position the contact so that the mating end of

the contact is on the locator side of the tool, and so

that the open “U” of the wire and insulation barrels

must face the top of the tool. Place the contact up

into the nest so that the movable locator drops into

the slot in the contact. Refer to Figure 3. Butt the

front end of the wire barrel against the movable

locator.

Make sure t at bot sides of t e insulation barrel

are started evenly into t e crimping section. Do

NOT attempt to crimp an improperly positioned

contact.

4. Hold the contact in position and squeeze the

tool handles together until ratchet engages

sufficiently to hold the contact in position. Do NOT

deform insulation barrel or wire barrel.

5. Insert stripped wire into contact insulation and

wire barrels until it is butted against the wire stop,

as shown in Figure 3.

6. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles

to open and remove crimped contact.

T e crimped contact may stick in t e crimping

area, but t e contact can be easily removed by

pus ing downward on t e top of t e locator (see

Figure 3).

7. Check the contact crimp height as described in

Section 6, CRIMP HEIGHT INSPECTION. If

necessary, adjust the crimp height as described in

Section 7, CRIMP HEIGHT ADJUSTMENT.

6. CRIMP HEIGHT INSPECTION

This inspection requires the use of a micrometer with

a modified anvil.

Tyco Electronics does not manufacture or market

t ese micrometers. However TE recommends t e

modified micrometer (Crimp Heig t Comparator

RS-1019-5LP) or t e digital micrometer from

Mitutoyo.

Proceed as follows:

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed.

2. Refer to Section 5, CRIMPING PROCEDURE,

and crimp the contact(s) accordingly.

3. Using a crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to that shown in the table,

the tool is considered dimensionally correct. If not,

the tool must be adjusted. Refer to Section 7,

CRIMP HEIGHT ADJUSTMENT.

Position Point

on Center of

Wire Barrel

Opposite

Seam

A"

Modified Anvil

IRE SIZE CRIMP SECTION CRIMP HEIGHT

DIMENSION A

mm2(Max) (Color Marking)

DIMENSION A

(+0.05 [+.002])

2.5 Yellow 1.88 [.0740]

1.5 Blue 1.58 [.0621]

1.0 Red 1.36 [.0535]

0.75 Green 1.27 [.0500]

Figure 4

7. RATCHET (Crimp Height) ADJUSTMENT

(Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel

from the locator side of the tool.

3. Observe the ratchet adjustment wheel. If a

tighter crimp is required, rotate the adjustment

wheel

counterclockwise

to a higher–numbered

setting. If a looser crimp is required, rotate the

adjustment wheel

clockwise

to a lower–numbered

setting.

4. Re–assemble the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, replace and

secure the lockscrew. If the dimension is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

8. MAINTENANCE

Ensure that the tool and dies are clean by wiping

them with a clean, soft cloth. Remove any debris with

a clean, soft brush. Do not use objects that could

damage the tool. When not in use, keep handles

closed to prevent objects from becoming lodged in

the crimping dies, and store in a clean, dry area.

CAUTION

NOTE

408-4342

PRO-CRIMPER III Hand Crimping Tool Ass mbly 58603-1

of 5Rev

Tyco Electronics Corporation

Figure 5

Scre driver

Ratchet

Adjustment

Wheel

Lockscre

(Typ)

9. VISUAL INSPECTION

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 10, REPLACEMENT.

10. REPLACEMENT

Customer–replaceable parts are shown in Figure 1.

Available separately, PRO–CRIMPER III Hand

Crimping Tool Repair Kit 679221–1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

If the dies are damaged or worn excessively, they

must be replaced.

Order the repair kit and replaceable parts through

your Tyco Electronics representative, or call

1–800–526–5142, or send a facsimile of your

purchase order to 717–986–7605, or write to:

CUSTOMER SERVICE (38–35)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105–3608

11.REVISION SUMMARY

Since the previous release of this instruction sheet,

the following changes have been made:

PRO–CRIMPER II Hand Tool became the

PRO–CRIMPER III Hand Tool;

The TE logo was applied; and

The format was updated to the current

corporate requirements.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tyco Electronics Outils de sertissage

Tyco Electronics

Tyco Electronics 603995 Series Manuel utilisateur

Tyco Electronics

Tyco Electronics AMP PRO–CRIMPER II Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 48858-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 58593-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics DYNA-CRIMP 69065 Manuel utilisateur

Tyco Electronics

Tyco Electronics AMP SDE PEW 12 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 90654-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 0-0654174-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 58591-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 696675-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 9-1478246-0 Manuel utilisateur

Tyco Electronics

Tyco Electronics PIDG STRATO-THERM Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 1752787-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 408-10050 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP II Manuel utilisateur

Tyco Electronics

Tyco Electronics ERGOCRIMP 2-1579021-9 Manuel utilisateur

Tyco Electronics

Tyco Electronics PIDG Series Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFB Manuel utilisateur

TE Connectivity

TE Connectivity 539 726-2 Manuel utilisateur