Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Instruction Sheet

PRO-CRIMPER* III Hand ool Assembly 408-9830

L C B

of 3

2007 Tyco Electronics Corporation, Harrisburg, PA

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

*Trademark. ther products, logos, and company names used are the property of their respective owners.

T LING ASSISTANCE CENTER 1-800-722-1111

PR DUCT INF RMATI N 1-800-522-6752 This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at

www.tycoelectronics.com

08 AUG 07 Rev E

58499-1 with Die Assembly 58483-1

PROPER USE GUIDELINES

CumulativeTrauma Disorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

The PR -CRIMPER III Hand Tool is a Commercial" grade tool and is

designed primarily for field installation, repair, maintenance work, or

prototyping in industrial, commercial, or institutional applications. Product

crimped with this tool will meet the crimp height requirement for hand tools in

the appropriate Application Specification (114-series), but may not comply

with other feature parameters of the specification. A variety of tools are offered

to satisfy your performance requirements. For additional information, contact

the Tooling Assistance Center at 1-800-722-1111.

Die Assembly

Moving Jaw

Ratchet Adjustment

Wheel

Moving Handle

Stationary Handle

PR -CRIMPER III Hand Tool

Frame 354940-1 (See Instruction

Sheet 408-9930)

Pivot Pin

Back of Tool

(Wire Side)

Stationary

Jaw

DIE ASSEMBLY PRODUC

FAMILY FLEXIBLE COAXIAL

CABLE SIZE (RG/U)

DIE ASSEMBLY

CRIMPING CHAMBER

MARKING

178, 196 .105 (A)

58483-1 SMB Straight Cable

Plug Connectors

174, 179, 187, 188, 316 .128 (B)

Plug Connectors

174, 188, 316 (All Double Braid) .151 (C)

Figure 1

1. IN RODUC ION

PRO–CRIMPER III Hand Tool Assembly 58499–1

consists of PRO–CRIMPER III Hand Tool Frame

354940–1 and Die Assembly 58483–1. The tool

assembly is used to crimp the ferrule of the

connectors listed in Figure 1. In this use, the die

assembly does not provide for crimping of the center

contact.

Read these instructions thoroughly before using the

tool assembly.

Dimensions in this instruction sheet are in

millimeters [with inches in brackets]. Figures are

not drawn to scale.

For additional information on the hand tool frame,

refer to 408–9930. Refer to the applicable connector

instruction sheet for assembly of the connector.

Reasons for reissue of this instruction sheet are

provided in Section 8, REVISION SUMMARY.

NO E

Downloaded from Arrow.com.

408-9830

PRO-CRIMPER III Hand Tool Assembly 58499-1 with Die Assembly 58483-1

Rev

of 3 Tyco Electro ics Corporatio

2. DESCRIPTION

(Figure 1)

The tool frame features a stationary jaw and handle, a

moving jaw, a moving handle, and an adjustable

ratchet that ensures full crimping. The tool frame

holds the die assembly.

The die assembly consists of an indenter (stationary

die) and an anvil (moving die). When closed, the dies

form three crimping chambers. Each die is held in the

hand tool frame by a single screw.

3. INSTALLATION AND REMOVAL OF

DIE ASSEMBL

(Figure 2)

1. Close the tool handles until the ratchet releases,

then allow the handles to open fully.

2. Insert the dies into the tool jaws as shown in

Figure 2, and align the retaining holes in each die

with the associated hole in the tool.

Figure 2

Tool Frame

Jaws

Die Retai i g

Screws

A vil

I de ter

3. Thread, but do not tighten, the die retaining

screws into the holes.

4. Carefully close the tool handles, making sure

that the dies align properly.

5. Tighten the die retaining screws with the

appropriate hex wrench.

6. To disassemble, close the tool handles until the

ratchet releases, remove the two die retaining

screws, and slide the dies out of the tool jaws.

4. CRIMPING PROCEDURE

(Ferrule O ly)

Make sure that the center contact is properly crimped

and assembled onto the connector as described in

applicable connector instruction sheet. Then proceed

as follows:

1. Slide the ferrule over the cable braid until it is

positioned against the shoulder of the plug body.

2. Close the tool handles until the ratchet releases,

then allow the handles to open FULLY.

3. Place the ferrule in the appropriate crimping

chamber on the anvil die so that the shoulder of

the plug body is close to the edge of the die. Refer

to Figure 3.

Refer to Figure 1 for the appropriate crimping

chamber.

Figure 3

Shoulder of Plug

Body Close to

Edge of Die

Crimpi g

Chamber

(Ref)

4. While holding the assembly, close the tool

handles until the dies hold the ferrule in place.

5. Carefully close the tool handles until the ratchet

releases, then allow the handles to open FULLY.

6. Remove the ferrule from the dies.

7. Inspect the crimped ferrule according to

applicable connector instruction sheet. If

necessary, adjust the ratchet as described in

Section 5.

5. RATCHET ADJUSTMENT

(Figure 4)

The tool ratchet mechanism features an adjustment

wheel with numbered settings. The adjustment wheel

controls the amount of handle pressure exerted on

the jaws during crimping. If the crimp is not

acceptable, adjust the ratchet as follows:

1. Remove the lockscrew from the ratchet

adjustment wheel.

NOTE

Downloaded from Arrow.com.Downloaded from Arrow.com.

408-9830

PRO-CRIMPER III Hand Tool Assembly 58499-1 with Die Assembly 58483-1

of 3Rev

Tyco Electro ics Corporatio

Screwdriver

Ratchet

Adjustme t

Wheel

Lockscrew

Figure 4

2. With a screwdriver, adjust the ratchet wheel

from the front of the tool.

3. Observe the ratchet adjustment wheel. If a

tighter crimp is required, rotate the adjustment

wheel

counterclockwise

to a higher–numbered

setting. If a looser crimp is required, rotate the

adjustment wheel

clockwise

to a lower–numbered

setting.

4. Re–assemble the lockscrew.

5. Make a sample crimp. If the crimp is acceptable,

the adjustment setting is correct. If the crimp is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

6. MAINTENANCE AND INSPECTION

6.1. Maintenance

Ensure that the tool frame and dies are clean by

wiping them with a clean, soft cloth. Remove any

debris with a clean, soft brush. Do not use objects

that could damage any components. When not in use,

keep tool handles closed to prevent objects from

becoming lodged in the dies, and store in a clean, dry

area.

6.2. isual Inspection

Inspection of the dies should be made on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimping sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the dies must be replaced.

Refer to Section 7, REPLACEMENT.

6.3. Measuring Die Opening

Figure 5 provides dimensions for the die openings.

DIE OPENING DIMENSION +0.10 [+.004]

A B C

2.667 [.105] 3.251 [.128] 3.835 [.151]

Figure 5

7. REPLACEMENT

Customer–replaceable parts are shown in Figure 1.

Available separately, Repair Kit 679221–1 includes a

replacement nut and a variety of pins, rings, screws,

and springs. If the dies are damaged or worn

excessively, they must be replaced. Order the repair

kit and replaceable parts through your representative,

or call 1–800–526–5142, or send a facsimile of your

purchase order to 717–986–7605, or write to:

CUSTOMER SERVICE (038–035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105–3608

8. RE ISION SUMMARY

Revisions to this instruction sheet include:

Updated document to corporate requirements

Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.

Ce manuel convient aux modèles suivants

Autres manuels Tyco Electronics Outils de sertissage

Tyco Electronics

Tyco Electronics DYNA-CRIMP 69065 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III 58517 Series Manuel utilisateur

Tyco Electronics

Tyco Electronics SOLARLOK 1579004-9 Manuel utilisateur

Tyco Electronics

Tyco Electronics 58571-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PIDG STRATO-THERM Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO- CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 58591-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics SDE PEW-12 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics AMP SDE PEW 12 Manuel utilisateur

Tyco Electronics

Tyco Electronics CERTI-CRIMP II Manuel utilisateur

Tyco Electronics

Tyco Electronics 9-1478246-0 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 2063195-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics 48858-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics 58649-1 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

Tyco Electronics

Tyco Electronics AUTOPRESS C120 Note de version

Tyco Electronics

Tyco Electronics 1490748-1 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFB Manuel utilisateur

TE Connectivity

TE Connectivity 539 726-2 Manuel utilisateur