Tuff Mount C7016 Manuel utilisateur
6. Installing the Display
INSTALLATION MANUAL
LCD Ceiling Mount
C7016
55"
MAX
75x75 100x100
200x100/200x200
300x300/400x400
/
ISSUED: DEC. 2015
30kg
(66lbs)
RATED
30kg
(66lbs)
RATED
7. Adjustment
Use the tilt adjusting knob to adjust your display to the desired angle then tighten it.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
Tighten all screws but do not over tighten.
Lift the display and match the holes on your display with the holes on the VESA plate. Secure your
display to the mount by tightening screws.
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.
TV
TV
TVTV
7
CAU T ION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
M-A/ B/M-CM- M-F/M-G
or
M-C
M-G
D
M-E
M-
M-G
M-H M-I
180°
+20°
-20°
FOR CUSTOMER SERVICE CALL 855-449-8833 TUFF
D
M-E
M-
M-G M-I
M-H
M-C
M-D
M-E M-G M-H
M-H
21
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
concrete anchor
W-B
(x4)
ST6.3x55 (x4)
W-A
D8 (x4)
M-G
washer
D (x4)
M-F
5 washer small spacer
M-H
(x8)
M8x20
M-C
(x4)
M5x14
M-A
(x4) M6x14
M-B
(x4)
plastic cover
D
(x1)
grip holder (x1)
F
ceiling plate
E
(x1)
plastic bushing (x2)
C
outer column (x1)
A
inner column
B
(x1) M8 washer (x2)
G
M6x45(x3)
H
M8x45(x1)
I
knob (x1)
K
plastic pad (x1)
P
M6 nut (x3)
M
M8 nut (x1)
N
washer (x1)
L
M8x20 (x1)
O
VESA plate
Q
(x1)
D8 (x2)
J
washer
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone with good mechanical ability
who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wooden joist ceiling, make sure that mounting screws are anchored
into the center of the joist. The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
VESA adapter
R
(x2) VESA adapter (x2)
S
M6 screw
T
(x8)
M8x30 (x4)
M-E
M6x30 (x4)
M-D
small spacer (x4)
M-I
WARNING
• Make sure that mounting screws are anchored into the center of the joist. The use of a stud
finder is highly recommended.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
4
3
1a. For Wooden Joist Ceiling Mounting
Drill two
pilot holes
3
Screw the
ceiling plate
onto the
ceiling
3mm
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
(2.2")
2
1
Find and mark
the exact location
of mounting holes
W-A
Hang the ceiling plate so that the screws
fit into the keyhole openings. Turn the
ceiling plate into place and then tighten
the screws.
1b. Solid Brick and Concrete Block Mounting:
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
1b. For Solid Brick and Concrete Mounting
Drill four
pilot holes
2
Screw the
ceiling plate
onto the
ceiling
3mm
Hang the ceiling plate so that the screws fit into the keyhole openings. Turn the ceiling plate into place .
Do not tighten screws at this time. Fix the ceiling plate using the two other screws and then tighten all
the screws!
60mm
(2.4")
60mm
(2.4")
ø 10mm
(ø 3/8")
1
Mark the exact
location of
mounting
holes
W-A
W-B
W-A
X
Tighten both screws leaving
a 3mm space from the ceiling.
Tighten both screws
leaving a 3mm space
from the ceiling.
65
HM
C
2. Installing the Outer Column to the Ceiling Plate
HM
C
3. Installing the Inner Column and Routing Cables
Insert the plastic bushing and the inner column into the outer column and fix them at the desired height
using the correct combination of screws and nuts.
Run the power cable
through columns.
5. Installing the VESA Plate
4. Assembling the VESA Plate
N
G
I
G
J
K
J
L
O
T
S
S
R
R
Autres manuels Tuff Mount Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
