Trotec TTK 171 ECO Manuel utilisateur
TRT-BA-TTK171ECO-TC2014-18-003-EN
TTK 171 ECO
EN
ORIGINAL INSTRUCTIONS
DEHUMIDIFIER
2 EN
dehumidifier TTK 171 ECO
Table of contents
Notes regarding the instructions ..........................................2
Safety .....................................................................................2
Information about the device................................................4
Transport and storage...........................................................6
Assembly and installation.....................................................6
Operation .............................................................................10
Available accessories..........................................................13
Errors and faults..................................................................13
Maintenance ........................................................................15
Technical annex...................................................................19
Disposal ...............................................................................19
Declaration of conformity ...................................................20
Notes regarding the instructions
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information
(e.g. material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
instructions must be observed.
You can download the current version of the instructions and
the EUdeclaration of conformity via the following link:
TTK 171 ECO
https://hub.trotec.com/?id=42377
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Let the device dry out after a wet clean. Do not operate it
when wet.
• Do not use the device with wet or damp hands.
• Do not expose the device to directly squirting water.
• Never insert any objects or limbs into the device.
• Do not cover or transport the device during operation.
• Do not sit on the device.
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
• Check accessories and connection parts for possible
damage prior to every use of the device. Do not use any
defective devices or device parts.
EN 3
dehumidifier TTK 171 ECO
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Observe the device's power input, cable length and
intended use when selecting extensions to the power
cable. Completely unroll extension cables. Avoid electrical
overload.
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
• When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
• Make sure that the air inlet and outlet are not obstructed.
• Make sure that the suction side is kept free of dirt and
loose objects.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Only transport the device in an upright position with an
emptied condensation tank or drain hose.
• Discharge the collected condensate before transport and
storage. Do not drink it. Health hazard!
Intended use
Only use the device for drying and dehumidifying room air, while
adhering to and following the technical data.
Intended use comprises:
• dehumidifying and drying:
– living rooms, bedrooms, bathrooms and basements
– laundries, holiday homes, camper vans, boats
• maintaining the dryness of:
– storage spaces, archives, laboratories, garages
– bathrooms, wash rooms, changing rooms etc.
Improper use
The device is not intended for industrial use.
• Do not place the device on wet or flooded ground.
• Do not place any objects, e.g. clothing, on the device.
• Do not use the device outdoors.
• Any unauthorised modifications, alterations or structural
changes to the device are forbidden.
• Any operation other than as described in this manual is
prohibited. Non-observance renders all claims for liability
and guarantee null and void.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the instructions, especially the
Safety chapter.
Maintenance tasks which require the housing to be opened
must only be carried out by specialist companies for cooling and
air-conditioning or by Trotec.
4 EN
dehumidifier TTK 171 ECO
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
Behaviour in the event of an emergency
1. Switch off the device.
2. In an emergency, disconnect the device from the mains
feed-in: Hold onto the mains plug while pulling the power
cable out of the mains socket.
3. Do not reconnect a defective device to the mains.
Information about the device
Description of the device
The device uses the principle of condensation to automatically
dehumidify rooms.
The fan sucks damp room air through the air inlet, the air filter,
the evaporator and to the condenser located behind it. The air is
cooled at the cold evaporator until it is below the dew point.
Water vapour contained in the room air precipitates on the
evaporator fins as condensation or rime. The dehumidified,
cooled air is slightly warmed at the condenser and blown out
again. The drier air thus conditioned mixes with the air in the
room. The humidity in the room where the device is positioned
is reduced as air constantly circulates through the device.
Depending on the air temperature and the relative humidity, the
condensed water either drops continuously or only during the
defrost phase through the integrated drain nozzle into the
condensation tank below. It is fitted with a float to measure the
filling level.
The device has an automatic defrost function. Defrosting takes
place electronically in air circulation mode.
Once the maximum filling level of the condensation tank is
reached or in case the condensation tank is not installed
correctly, the condensation tank indicator light (see chapter
Operating elements) is illuminated. The compressor and fan will
switch off. The condensation tank indicator light only goes out
again once the emptied condensation tank is reinserted.
Optionally, the condensed water can be drained by attaching a
hose at the condensation connection.
Moreover, an air hose connection can be used for the selective
admission of dry air or for drying hollows.
The device can reduce the relative humidity of a room to approx.
30%.
Because of the heat radiation generated during operation, the
room temperature may rise slightly.
Furthermore, the device can be switched on and off
automatically with time delay. The according number of hours
can be set in hourly increments (1h to 24h).
EN 5
dehumidifier TTK 171 ECO
Device depiction
1
2
3
4
5
11
10
6
8
9
7
No. Designation
1 Transport handle
2 Operating element
3 Recessed handle
4 Transport wheel
5 Feed-through for condensation drain hose
6 Air outlet
7 Condensation tank
8 Venting slots
9 Power cable holder
10 Foot
11 Air inlet with air filter
6 EN
dehumidifier TTK 171 ECO
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
Before transporting the device, observe the following:
• Switch the device off.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Do not use the power cable to drag the device.
• Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
• To make the device easier to transport, it is fitted with
wheels.
• Do not incline the device by more than 45°, for otherwise
the device could be damaged.
• Only wheel the device on a level and smooth surface.
After transporting the device, observe the following:
• Set up the device in an upright position after transport.
• Leave the device to rest for 12to24hours, so the
refrigerant can accumulate within the compressor. Wait
12to24hours before switching the device back on! Acting
contrary might lead to compressor damage and a
malfunctioning device. If so, any warranty claims will be
voided.
Storage
Before storing the device, observe the following:
• Drain the remaining condensate from the device and the
condensation drain hose (see chapter Maintenance).
• Empty and clean the condensation tank prior to storage.
• Drain any possibly remaining condensate.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• in an upright position where it is protected from dust and
direct sunlight
• with a cover to protect it from invasive dust, if necessary
• Place no further devices or objects on top of the device to
prevent it from being damaged.
Assembly and installation
Scope of delivery
• 1x Device
• 1 x Transport handle
• 2 x Foot
• 2x Transport wheel
• 1x Condensation drain hose
• 12x Screw
• 4x Nut
• 8x Washer
• 1x Manual
Unpacking the device
1. Open the cardboard box and take the device out.
2. Completely remove the packaging.
3. Fully unwind the power cable. Make sure that the power
cable is not damaged and that you do not damage it during
unwinding.
EN 7
dehumidifier TTK 171 ECO
Assembly
Use tools suitable for the intended task.
Mounting the feet
Prior to initial start-up, the feet must be attached to the device.
To do so, please proceed as follows:
1. Place the device on its front side.
2. Mount the two feet(10) to the device sides using two
screws each. The feet must protrude from the bottom side
of the device.
3. Then mount the wheels.
Mounting the wheels
Prior to initial start-up, the transport wheels and the axle must
be attached to the device. To do so, please proceed as follows:
üThe device is placed on its front side.
1. Place a washer(12) on the axle(13).
2. Place a wheel(4) in front of the washer.
3. Place a second washer(12) in front of the wheel(4).
4. Use a nut(14) to secure the wheel(4) on the axle.
12
13
12
4
14
5. Repeat this process on the other side of the axle.
6. After mounting the wheels and the feet, place the device in
an upright position.
Mounting the transport handle
Prior to initial start-up, the transport handle must be attached to
the device. To do so, please proceed as follows:
1. Mount the transport handle(1) to both feet(10) using two
screws.
8 EN
dehumidifier TTK 171 ECO
Connecting the (optional) air transport hose
For the selective admission of dry air or for drying hollows
please connect the optionally available hose adapter and air
hose (see chapter Available accessories).
1. Slide the hose adapter onto the connecting rails of the air
outlet(6).
2. Connect the air transport hose.
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the Technical data
chapter.
A
B
C
C
D
• Before restarting the device, check the condition of the
power cable. If there are doubts as to the sound condition,
contact the customer service.
• Set the device up in an upright and stable position.
• Do not create tripping hazards when laying the power
cable or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
• Make sure that extension cables are completely unrolled.
• When positioning the device, keep a sufficient distance to
heat sources.
• Make sure that no curtains or other objects interfere with
the air flow.
• When positioning the device, particularly in wet areas,
secure it locally with an RCD (residual current device)
which complies with the respective regulations.
EN 9
dehumidifier TTK 171 ECO
Inserting the air filter
Note
Do not operate the device without an inserted air filter!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
• Make sure that the air filter is installed before switching
the device on.
Inserting the condensation tank
• Ensure that the float inside the condensation tank is
inserted correctly.
• Ensure that the condensation tank is empty and inserted
correctly.
10 EN
dehumidifier TTK 171 ECO
Operation
Notes:
• Avoid open doors and windows.
• After being switched on, the device operates fully
automatically.
• The compressor will additionally be switched on after
3seconds.
• The fan runs permanently in dehumidification mode until
the set nominal value is reached.
Operating elements
TimerPlusMinusContinuousTank Full
Full Cont Defrost Timer
15 16 17 18 19 20 21
22
23
24
25
No. Designation Meaning
15 Tank Full LED Is displayed when the condensation tank
is full or not installed correctly
16 Continuous
button
Selection button for the operating mode
continuous operation
17 Minus button For reducing the desired relative
humidity level (20% to 90% in
increments of 5%)
For reducing the value of the timer
programming in increments of 1hour
(1h to 24h)
18 Segment display Indication of the current room humidity
level
Indication of the desired room humidity
level
Indication of the number of hours during
timer programming
19 Plusbutton For increasing the desired relative
humidity level (20% to 90% in
increments of 5%)
For increasing the value of the timer
programming in increments of 1hour
(1h to 24h)
20 Timer button For enabling or disabling the automatic
switch-on timer function
For enabling or disabling the automatic
switch-off timer function
21 On / Off button For switching the device on or off
No. Designation Meaning
22 Timer LED Illuminated when the timer for automatic
switch-on or switch-off is activated
23 Defrost LED Is displayed when automatic defrosting
is in progress
24 Continuous LED Illuminated during continuous operation
25 Full LED Is displayed when the condensation tank
is full or not installed correctly
Switching the device on
Once you have completely installed the device as described in
the Start-up chapter, you can switch it on.
1. Press the On/ Off button(21).
ðThe device starts to dehumidify in continuous operation.
2. Press the On/ Off button(21) again.
ðThen the compressor switches off.
ð- - will be indicated on the display.
ðThe device now switches over into standby mode.
ðThe fan keeps running for approx. one minute and then
switches off.
Continuous operation
The device dehumidifies the air constantly and regardless of the
relative room humidity.
The desired relative room humidity cannot be adjusted in this
operating mode.
1. Press the Continuous button(16).
ðThe Continuous LED(24) is illuminated.
ðThe segment display(18) indicates the current relative
room humidity.
ðContinuous operation is selected.
Info
For continuous operation the condensation drain hose
can be connected in order to continuously drain the
accumulating condensate.
Autres manuels pour TTK 171 ECO
1
Table des matières
Autres manuels Trotec Autre
