Trotec BC06 Manuel utilisateur

BC06

OPERATING MANUAL

HUMIDITY/AIR

TEMPERATURE

MEASURING INSTRUMENT

TRT-BA-BC06-TC-001-EN

1Operating manual – Humidity / air temperature measuring instrument BC06 EN

Symbols

Danger!

Warns of a hazard which can lead to injuries.

Caution!

Warns of a hazard which can lead to damage to property.

The current version of the operating manual can be found at:

www.trotec.de

Legal notice

This release replaces all previous versions. No part of this

publication may be reproduced without written permission from

TROTEC®. The same applies for electronically processing,

duplicating or spreading the publication. Subject to technical

guarantee that they may be used freely and primarily following

the spelling of the manufacturer. Product names are registered.

Changes to construction in the interests of constant improve-

ments to the product, as well as changes to the shape and colour

are reserved.

The scope of delivery may vary from product images. This

document was created with all due care. TROTEC®accepts no

liability whatsoever for possible mistakes or omissions.

The only party responsible for determining measured results to be

valid, drawing conclusions and deriving actions is the user!

TROTEC®accepts no claims of warranty for the correctness of

the determined measured values or measured results. Further,

TROTEC®accepts no liability whatsoever for possible mistakes or

damage which have been caused by utilising the determined

measured results. © TROTEC®

Description of the device

By use of the humidity / air temperature measuring instrument

the temperature and humidity indoors can be determined.

Further available for the assessment of the measurements is a

MAX/MIN function (maximum and minimum value).

The display illumination automatically adjusts to the ambient light

conditions.

When not in use, an automatic switch-off saves the battery.

Device depiction

Table of contents

Notes regarding the operating manual .................................... 1

Information about the device................................................... 1

Technical data ........................................................................ 2

Safety ..................................................................................... 2

Transport and storage............................................................. 3

Operation................................................................................ 3

Maintenance and repair .......................................................... 4

Disposal.................................................................................. 5

Declaration of conformity ........................................................ 5

Notes regarding the operating manual

Information about the device

No. Operating element

1 Measuring sensor

2 MAX/MIN button

3 Tripod thread

4 Battery compartment with cover

5Display

6 Light sensor

7On/Offkey

EN Operating manual – Humidity / air temperature measuring instrument BC06 2

Display

Scope of delivery

• 1 x humidity / air temperature measuring instrument BC06

• 1 x 9 V battery

• 1 x Getting started guide

Carefully read the operating manual before using the device

and keep it within reach!

• Do not use the device in atmospheres containing oil, sulphur,

chlorine or salt.

• Protect the device from permanent direct sunlight.

• Do not remove any safety signs, stickers or labels from the

device. Keep all safety signs, stickers and labels in legible

condition.

• Observe the storage and operating conditions (see chapter

Technical data).

Intended use

Only use the device for indoor temperature and humidity

measurements within the measuring range specified in the

technical data. Here, read and observe the technical data.

To use the device for its intended use, only use accessories and

spare parts which have been approved by TROTEC®.

Improper use

Do not use the device in potentially explosive atmospheres, for

measurements in liquids or at live parts. TROTEC®accepts no

liability for damages resulting from improper use. In such a case,

entitlements to a warranty are forfeited. Any unauthorised

modifications, alterations or structural changes to the device are

forbidden.

Personnel qualifications

People who use this device must:

• have read and understood the operating manual, especially

the Safety chapter.

No. Display element

8 Indication of the relative humidity

9 Indication of the minimum value

10 Indication of the measured humidity value

11 Indication of the measured temperature value

12 Indication of the temperature unit

13 Indication for automatic switch-off

14 Indication of the maximum value

15 Battery status indication

Technical data

Model: BC06

Weight: 152 g

Dimensions (H x W x D): 148 mm x 56 mm x 33 mm

Temperature

Measuring range: -20 to +60 °C or -4 to 140 °F

Accuracy: ± 1 °C (0 °C to 40 °C)

± 2 °C (-20 °C to 0 °C and 40 °C to 60 °C)

Measuring range resolution: 0.1 °C or 0.1 °F

Relative humidity

Measuring range: 0.0 to 100.0 % RH

Accuracy: ± 3.5 % RH (20 % to 80 %)

± 5 % RH (0 % to 20 % and 80 % to 100 %)

Measuring range resolution: 0.1 % RH

Reaction time: < 15 seconds

Operating temperature: 0 to 50 °C with < 80 % RH

Storage temperature: -40 to 85 °C with < 99 % RH

Power supply: 1 x Alkaline 9 V battery

battery life approx. 48 hours

Automatic switch-off of the

device:

If activated (13), after approx. 30 minutes of

non-use.

°C

°F

MAX MIN %RH

Safety

3Operating manual – Humidity / air temperature measuring instrument BC06 EN

Residual risks

Danger!

Do not leave the packaging lying around. Children may

use it as a dangerous toy.

Danger!

The device is not a toy and does not belong in the hands

of children.

Danger!

Dangers can occur at the device when it is used by

untrained people in an unprofessional or improper way.

Observe the personnel qualifications.

Caution!

To prevent damages to the device, do not expose it to

extreme temperatures, extreme humidity or moisture.

Caution!

Do not use abrasive cleaners or solvents to clean the

device.

Transport

For transporting the device use a suitable bag to protect it from

external influences.

Storage

When the device is not being used, observe the following storage

conditions:

•dry.

• protected from dust and direct sunlight,

• with a plastic cover to protect it from invasive dust, if

neces sary.

• The storage temperature is the same as the range given in

the chapter Technical data.

• When storing the device for a long time, remove the batteries.

Inserting the battery

• Insert the supplied battery before first use.

Caution!

Make certain that the surface of the device is dry and the

device is switched off.

1. Remove the cover (16) from the device by sliding it in the

direction of the arrow.

2. Use the battery clip (17) to connect the new battery with

correct polarity.

3. Slide the cover (16) back on the device.

Switch-on and measurements

1. Press the on/off key (7).

– The display is switched on and the device is ready for

operation.

– In case of poor lighting conditions the display illumination

switches on automatically. The display illumination is

controlled by the sensor (6).

2. Point the device at the area to be measured.

– The measured values are indicated in % RH and °C.

– Wait for a moment to achieve a stable measured value.

Note:

Note that moving from a cold area to a warm area can lead to

condensation forming on the device's circuit board. This physical

and unavoidable effect can falsify the measurement. In this case,

the display shows either no measured values or they are

incorrect. Wait a few minutes until the device has become

adjusted to the changed conditions before carrying out a

measurement.

Transport and storage

Operation

EN Operating manual – Humidity / air temperature measuring instrument BC06 4

Changing the unit °C / °F

The default setting for the temperature unit is °C.

1. Open the battery compartment.

2. Remove the battery.

– At the upper edge you can see an opening leading to the

inside of the device. That is where the switch is located.

3. Flip the switch by means of a suitable tool (e.g. a paper clip).

– The unit is set to °F.

MAX/MIN function

By use of the MAX/MIN function you can either read the highest

or the lowest value of the current measurement interval.

1. Press the MAX/MIN button (2).

– The indication MAX (14) appears on the display.

– The display now indicates the highest temperature and

humidity values measured since the device was

switched on.

2. Press the MAX/MIN button (2) again.

– The indication MIN (9) appears on the display.

– The display now indicates the lowest temperature and

humidity values measured since the device was

switched on.

3. Press the MAX/MIN button (2) again.

– The MAX/MIN function is deactivated and the currently

measured values are displayed.

Automatic switch-off

If the symbol for automatic switch-off (13) is displayed, the device

will switch off automatically when not in use for 30 minutes.

To deactivate automatic switch-off, please proceed as follows:

1. Press the MAX/MIN button (2) for approx. 2 seconds.

– The symbol (13) is no longer displayed.

– Automatic switch-off is deactivated.

2. Press the MAX/MIN button (2) again for approx. 2 seconds.

– Automatic switch-off is reactivated.

Switch-off

With activated automatic switch-off function (13) the device

switches off after 30 minutes of non-use.

• Press the On/Off key (7).

– The device will be switched off.

– The MAX and MIN values are reset.

Battery change

A battery change is required, when the Battery indication (15)

lights up or the device can no longer be switched on.

See Inserting the battery on page 3.

Cleaning

Clean the device with a soft, damp and lint-free cloth. Ensure that

no moisture enters the housing. Do not use any sprays, solvents,

alcohol-based cleaning agents or abrasive cleaners. Only use

clean water to moisten the cloth.

Repair

Do not modify the device. Never open the device housing or install

any spare parts. For repairs or device testing, contact the

manufacturer.

Maintenance and repair

5Operating manual – Humidity / air temperature measuring instrument BC06 EN

In the European Union, electronic equipment must not

be treated as domestic waste, but must be disposed of

professionally in accordance with Directive

2002/96/EC of the European Parliament and Council of

27th January 2003 concerning old electrical and electronic

equipment. At the end of its life, please dispose of this instrument

in a manner appropriate to the relevant legal requirements.

in accordance with the EC Low Voltage Directive 2006/95/EC

and the EC Directive 2004/108/EC about electromagnetic

compatibility.

Herewith, we declare that the humidity / air temperature measur-

ing instrument BC06 was developed, constructed and produced

in compliance with the named EC directives.

The marking is found on the rear of the device.

Manufacturer:

Trotec GmbH & Co. KG

Grebbener Straße 7

D-52525 Heinsberg

Phone: +49 2452 962-400

Fax: +49 2452 962-200

E-mail: info@trotec.com

Heinsberg, 31/03/2014

Managing Director: Detlef von der Lieck

Disposal Declaration of conformity

TROTEC GmbH & Co. KG

Grebbener Str. 7

52525 Heinsberg

Deutschland

+49 2452 962-0

+49 2452 962-200

info@trotec.com

www.trotec.com

Table des matières

Autres manuels Trotec Instrument de mesure

Trotec

Trotec BM12 Manuel utilisateur

Trotec

Trotec BA16WP Manuel utilisateur

Trotec

Trotec BD16 Manuel utilisateur

Trotec

Trotec BQ16 Manuel utilisateur

Trotec

Trotec BA30WP Manuel utilisateur

Trotec

Trotec BE44 Manuel utilisateur

Trotec

Trotec BE 38 Manuel utilisateur

Trotec

Trotec BP21WP Manuel utilisateur

Trotec

Trotec BY10 Manuel utilisateur

Trotec

Trotec TA400 Manuel utilisateur

Trotec

Trotec BC21 Manuel utilisateur

Trotec

Trotec BD22 Manuel utilisateur

Trotec

Trotec VSP3041 Manuel utilisateur

Trotec

Trotec LD6000 PTS Manuel utilisateur

Trotec

Trotec BM21 Manuel utilisateur

Trotec

Trotec BX09 Manuel utilisateur

Trotec

Trotec BM40 Manuel utilisateur

Trotec

Trotec BP17 Manuel utilisateur

Trotec

Trotec BM40 Manuel utilisateur

Trotec

Trotec TD200 Manuel utilisateur

Trotec

Trotec PDR 908 HP Manuel utilisateur

Trotec

Trotec BQ20 Manuel utilisateur

Trotec

Trotec BE52 Manuel utilisateur

Trotec

Trotec BM22WP Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur