Trotec PSCS 10-12V Manuel utilisateur
TRT-BA-TRT-BA-PSCS10-12V-TC-002-EN
PSCS 10-12V
EN
ORIGINAL INSTRUCTIONS
CORDLESS DRILL DRIVER
1 EN
Operating manual – cordless drill driver PSCS 10-12V
table of contents
Notes regarding the operating manual.................................1
Safety .....................................................................................2
Information about the device................................................7
Transport and storage...........................................................9
Start-up..................................................................................9
Operation .............................................................................13
Available accessories..........................................................14
Errors and faults..................................................................15
Maintenance ........................................................................16
Disposal ...............................................................................16
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning of explosive substances
This symbol indicates dangers to the life and health of
persons due to potentially explosive substances.
Warning!
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution!
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
Wear safety glasses
Information marked with this symbol indicates that you
should wear eye protection.
Wear a protective mask
Information marked with this symbol indicates that you
should wear a protective mask.
Wear Ear Protection
Information marked with this symbol indicates that you
should wear hearing protection.
The current version of the operating manual can be found at:
PSCS 10-12V
https://hub.trotec.com/?id=42665
EN 2
Operating manual – cordless drill driver PSCS 10-12V
Legal notice
This release replaces all previous versions. No part of this
publication may be reproduced without written permission from
TrotecGmbH&Co.KG. The same applies for electronically
processing, duplicating or spreading the publication. Subject to
technical changes. All rights reserved. Trademarks are used
without guarantee that they may be used freely and primarily
following the spelling of the manufacturer. Product names are
registered.
Changes to construction in the interests of constant
improvements to the product, as well as changes to the shape
and colour are reserved.
The scope of delivery may vary from product images. This
document was created with all due care. TrotecGmbH&Co.KG
accepts no liability whatsoever for possible mistakes or
omissions.
© TrotecGmbH&Co.KG
Warranty and liability
The device complies with the fundamental health and safety
requirements of the applicable EU regulations and was tested at
the factory for perfect functionality multiple times.
However, if faults in the functionality occur and cannot be
remedied with the measures in the chapter Errors and faults,
please get in touch with your dealer or distributor.
When making a warranty claim, supply the device number (see
the side of the device).
When manufacturer's instructions or legal regulations have not
been followed, or after unauthorised changes to the device are
made, the manufacturer is not responsible for the resulting
damages. Changes to the device or unauthorised replacement
of individual parts can drastically impact the electrical safety of
this product and will result in the loss of the warranty. Liability
does not extend to damages to people or property caused by the
device being used other than as described in the instructions in
this operating manual. Subject to changes to technical design
and model changes as part of constant development and
product improvement without prior notice.
No liability is accepted for damages resulting from improper
use. In such a case, any warranty claims will be voided also.
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
General Power Tool Safety Warnings – Work area
safety
•Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
•Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
3 EN
Operating manual – cordless drill driver PSCS 10-12V
General Safety Warnings – Electrical safety
•Power tool or power adapter plugs must match the
outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce
risk of electric shock.
•Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
•Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
•Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
•If operating a power tool in a damp location is
unavoidable, use a residual current device(RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
•Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
General Power Tool Safety Warnings – Personal
safety
•Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
•Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
•Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
•Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
•Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
EN 4
Operating manual – cordless drill driver PSCS 10-12V
General Power Tool Safety Warnings – Power tool
use and care
•Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the
job better and safer at the rate for which it was designed.
•Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and / or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
•Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
•Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
•Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
•Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
General Power Tool Safety Warnings – Service
•Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
General Battery Pack / Charger Safety Warnings
•Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
•When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
•Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
•Do not charge other battery packs. The charger is only
suitable for use with the supplied battery pack and with
the voltages specified in the technical data. Otherwise,
there is a risk of fire and explosion.
•Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
•In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
•Do not open the battery. There is danger of a short
circuit.
•Do not short-circuit the battery. There is danger of
explosion.
•Batteries must not be exposed to mechanical impacts.
•Protect electrical parts against moisture. To prevent an
electric shock, never immerse them in water or other
liquids during cleaning or operation. Never hold the
charger under running water. Please observe the
instructions for cleaning and maintenance.
5 EN
Operating manual – cordless drill driver PSCS 10-12V
• The charger is only suited for indoor use.
• Keep the charger clean. Contamination entails a risk of
electric shock.
• Do not operate the charger on highly combustible ground
(e.g. paper, textiles etc.) or in an inflammable environment.
The heat generated by the charger during charging entails
a risk of fire.
• Only use the charger for charging the battery. The charger
must not be used as power supply for the power tool.
Device-specific safety warnings for cordless drill
drivers
Wear eye and mouth protection when processing
materials that may contain harmful substances (e.g.
asbestos).
• Secure the workpiece with tensioning devices or a vice.
• Hold the power tool firmly. When tightening or loosening
screws, high reaction torques can occur temporarily.
• Immediately switch off the power tool if the insertion tool
blocks. Beware of high reaction torques causing a
kickback.
•Hold power tool by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
• For any work on the device, as well as during transport or
storage, set the switch for the rotational direction to centre
position (locked). This prevents unintentional starting of the
power tool.
Residual risks
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Warning of electrical voltage
Before any work on the device, remove the mains plug
from the mains socket and the battery from the device!
Hold onto the mains plug while pulling the power cable
out of the mains socket.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning of explosive substances
Do not expose the battery to temperatures above 45
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
risk of explosion!
Warning!
Toxic dusts!
The harmful / toxic dusts produced during operation
pose of risk to the health of the operator and persons
in the vicinity.
Wear eye protection and a protective mask!
Warning!
Do not process materials containing asbestos.
Asbestos is considered carcinogenic.
Warning!
Make sure not to hit power, gas or water lines when
working with a power tool.
If necessary, use a pipe detector to check the wall you
want to drill in or slit open.
Warning!
Risk of injuries caused by flying parts or bursting tool
heads.
Warning!
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
EN 6
Operating manual – cordless drill driver PSCS 10-12V
Warning!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning!
The device is not a toy and does not belong in the
hands of children.
Caution!
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
Caution!
Keep a sufficient distance from heat sources.
Note
To avoid damaging the gear, only change the rotational
direction when the device is at a standstill.
Note
Set the torque and rotational direction according to the
operating mode. A wrong selection may damage the
device.
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Intended use
Only use the device PSCS 10-12V:
• for screwing in and loosening screws,
• for drilling in wood, plastic, ceramic and metal,
whilst adhering to the technical data.
Improper use
The device is not intended for drilling in concrete or natural
stone.
Personnel qualifications
People who use this device must:
• have read and understood the operating manual, especially
the Safety chapter.
7 EN
Operating manual – cordless drill driver PSCS 10-12V
Information about the device
Device description
The cordless drill driver has two speed levels: while the first
speed level is suitable for screwing, drilling can be performed
using the second speed level.
The integrated torque selection, including one drilling setting,
allows you to use the optimum power for every application,
adapted to the material and screw size.
The keyless drill chuck with automatic spindle lock further
enables an easy and tool-free exchange of the insertion tools.
The integrated LED work lamp offers an improved illumination of
the workpiece or working surface,
Device depiction
1 2 3
4
5
6
7
15
8
14
13
12
11 9
10
No. Designation
1 Keyless drill chuck
2 Torque selection
3 Gear selection (2 speed levels)
4 3-stage battery level indication
5 Clockwise / counter-clockwise rotation, lock
6 Handle
7 Battery
8 Quick charger
9 Green battery LED (quick charger ready for operation)
10 Bits
11 Red battery LED (battery charging)
12 Unlocking button
13 Battery holder
14 On / off switch (speed regulation)
15 LED work lamp
Scope of delivery
1x Cordless drill driver
1x Battery
2x Bits (50 mm)
1x Quick charger
1x Transport case
1x Manual
EN 8
Operating manual – cordless drill driver PSCS 10-12V
Technical data
Parameter Value
Model PSCS 10-12V
Nominal voltage 12 V
Idle speed
1st speed level
2nd speed level
0 – 400 rpm
0 – 1300 rpm
Torque settings 19 +1
Chucking range 10 mm
Max. drilling diameter
Wood
Metal
20 mm
8 mm
Max. torque 22 Nm
Weight 1 kg
Battery PSCS 10-12V DC
Type Li-ion
Nominal voltage 12 V
Capacity 1500 mAh
Quick charger PSCS 10-12V AC
Input
Nominal voltage 220 – 240 V ~ 50 Hz
Power input 45 W
Output
Nominal voltage 12.8 V
Charging current 2.0 A
Charging time 1 h
Protection class II /
Sound values according to EN 60745
Sound pressure level 63.1 dB(A)
Sound power level 74.1 dB(A)
Uncertainty K 3 dB(A)
Vibration information according to EN 60745
Vibration emission value drilling in
metal / screwing ah=in
1.58 m/s2
Uncertainty K 1.5 m/s2
Information on noise and vibration:
• The vibration level specified in these instructions was
determined by means of a measuring method standardized
in EN 60745 and can be used for a device comparison. The
specified vibration emission value may also be used for a
preliminary assessment of the exposure.
Caution!
Vibration emissions can cause a health hazard if the
device is used for an extended period of time or if it is
not properly handled and maintained.
• The vibration level will change depending on the
application of the power tool and may in some cases differ
from the value specified in these instructions. The vibration
load may be underestimated if the power tool is used
regularly in such a way. For a precise estimation of the
vibration load during a certain work period, it is also
important to consider the periods during which the device
is switched off, or is running but not actually employed.
This can reduce the vibration load over the entire work
period significantly.
9 EN
Operating manual – cordless drill driver PSCS 10-12V
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
For transporting the device, use the transport case included in
the scope of delivery in order to protect the device from external
influences.
Before transporting the device, proceed as follows:
• Switch off the device by setting the switch for clockwise /
counter-clockwise rotation to centre position(lock).
• Allow the device to cool down.
• Remove the battery from the device.
The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in
a way that it cannot move inside the packaging.
– Please also observe any other national regulations.
Storage
Before storing the device, proceed as follows:
• Set the switch for clockwise / counter-clockwise rotation
to centre position(lock).
• Clean the device as described in the Maintenance chapter.
• For storing the device, use the transport case included in
the scope of delivery in order to protect the device from
external influences.
• Remove the battery from the device.
• Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• ambient temperature below 40 °C
• protected from dust and direct sunlight inside the transport
case
Start-up
Unpacking the device
• Take the transport case out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
• Check the contents of the transport case for completeness
and look for damages.
Warning!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.
Table des matières
Autres manuels Trotec Percer
