Tripp Lite B110-SP-CAT-OD Manuel utilisateur

1111 W. 35th Street, Chicago, IL 60609 USA

tripplite.com/support

Owner’s Manual

IP66-Rated Gigabit PoE

Outdoor Surge Protector

Model: B110-SP-CAT-OD

All trademarks are the property of their respective owners.

WARRANTY REGISTRATION

to win an ISOBAR surge protector in our monthly drawing!

tripplite.com/warranty

Español 13 • Français 25 • Русский 37

19-11-220-933B57-BOOK.indb 119-11-220-933B57-BOOK.indb 1 2/5/2020 1:28:50 PM2/5/2020 1:28:50 PM

Package Includes

• B110-SP-CAT-OD Outdoor Surge Protector

• 18 AWG Grounding Wire – 1 ft.

• Metric Cable Gland, 8.4 mm Diameter (x2)

• PCBA Mounting Screws (x2)

• (x4) Surface Screw Anchors

• (x4) Surface Mounting Screws

• Unit Cover Screws (x4)

• Owner’s Manual

Product Features

• Protects valuable outdoor PoE equipment from power

surges, lightning, ESD and cable discharge events in

unforgiving environments

•

Complies with 802.3af, 802.3at and 802.3bt IEEE

Standards

• Support PoE devices up to 90W and Ethernet speeds up to

1 Gbps

• Meets the following IEC regulations:

o IEC 61000-4-2 (ESD) +/- 15kV(Air), +/- 8kV(Contact)

o IEC 61000-4-5 (Lightning) 10kA (8/20µs), 20kV (8/20µs)

• Supports both Mid- and End-Span PoE

• Passive by design—no external power required

Optional Accessories

• N224-Series Cat6 Plenum-Rated Solid-Core Bulk Cable

• T100-001-TST Wire Crimper with Built-In Cable Tester

19-11-220-933B57-BOOK.indb 219-11-220-933B57-BOOK.indb 2 2/5/2020 1:28:50 PM2/5/2020 1:28:50 PM

Figure 2Figure 1

Mounting Instructions

On the bottom of the enclosure, the distance from the center

to center of each mounting hole are engraved (Figure 1).

Securely mount the bottom portion of the enclosure to the

desired outdoor location. Screw hole diameter supports

mounting screw sizes up to M3.5.

Note: Mount the enclosure with the screw slit side in the bottom

right corner, see Figure 2)

19-11-220-933B57-BOOK.indb 319-11-220-933B57-BOOK.indb 3 2/5/2020 1:28:51 PM2/5/2020 1:28:51 PM

Metric Cable Gland Assembly

Protect outdoor edge network devices like PoE cameras or

LAN access points from water, dust or electrical damage by

installing the B110-SP-CAT-OD between the source and edge

network equipment.

Note: Maximum cable distance between B110-SP-CAT-OD and

source is 328 ft. (100 m); maximum cable distance between

B110-SP-CAT-OD and equipment is 328 ft. (100 m). For best

protection performance, the total cable distance in the installation

should not exceed 328 ft. (100 m).

Note: The B110-SP-CAT-OD must be grounded to function properly.

Installation

19-11-220-933B57-BOOK.indb 419-11-220-933B57-BOOK.indb 4 2/5/2020 1:28:51 PM2/5/2020 1:28:51 PM

Note: Use standard size Cat5e, Cat6 or Cat6a cables that feature a

wire gauge of 23/24 AWG. Slim category cables are not supported.

1. Remove both the cap Aand end nut Efrom one of the

metric cable glands (refer to section Metric Cable Gland

Assembly). Slide the cap and remaining portion of the

metric cable gland onto both the included grounding wire

and bare-wire category cable coming from your source (ex:

PoE switch) as shown:

Note: Use standard size Cat5e, Cat6 or Cat6a cabling that features

a wire gauge of 23/24 AWG. Slim category cables are not supported.

Installation

PoE Camera

Equipment (Edge) Protection Only

This installation protects only your edge equipment from

surge, lightning or ESD damage. To protect both the source

and edge equipment, refer to section Source and Equipment

(Edge) Protection.

19-11-220-933B57-BOOK.indb 519-11-220-933B57-BOOK.indb 5 2/5/2020 1:28:51 PM2/5/2020 1:28:51 PM

2. Insert both the grounding wire and the bare-wire end of the

category cable in the enclosure, making sure it is inserted

on the side with the slit.

3. Using a crimping tool (such as Tripp Lite’s T100-001-TST,

sold separately), crimp an RJ45 connector to the bare end

of the category cable.

Screw the metric cable gland to the enclosure using the

end nut Epreviously removed in Step 1. Then tighten

the cap securely onto the metric cable gland.

Installation

19-11-220-933B57-BOOK.indb 619-11-220-933B57-BOOK.indb 6 2/5/2020 1:28:51 PM2/5/2020 1:28:51 PM

Installation

4. Repeat Steps 1-3 for the equipment (ex: PoE camera) side

of the enclosure without the addition of a grounding wire.

Note: To achieve the best protection performance, the Cat5e/6/6a

patch cable between the equipment end of the B110-SP-CAT-OD surge

protector and the equipment to be protected must not exceed 300 ft.

5. Once both bare wires are crimped, connect the newly

crimped RJ45 cables to the PCBA, then secure the PCBA

board to the enclosure using the included mounting screws.

Lastly, attach the grounding wire to the available screw on

the PCBA board.

Note: Ensure the cable end of the PCBA is facing the side with the

slit and the equipment end facing the other. Make sure you connect

your source to the cable end, and your PoE-compliant device to the

equipment end.

Equipment End

19-11-220-933B57-BOOK.indb 719-11-220-933B57-BOOK.indb 7 2/5/2020 1:28:51 PM2/5/2020 1:28:51 PM

Installation

6. Screw the front cover to the back portion of the enclosure

using the included unit cover screws, making sure both the

groove and the slit line up.

7. The connected PoE device is now protected.

Equipment End

19-11-220-933B57-BOOK.indb 819-11-220-933B57-BOOK.indb 8 2/5/2020 1:28:51 PM2/5/2020 1:28:51 PM

Source and Equipment (Edge) Protection

The previous installation only protects your edge equipment

from surge, lightning or ESD damage. To protect both the

source and edge equipment, install two B110-SP-CAT-OD

units in your application. A B110-SP-POE can be installed

instead of a second B110-SP-CAT-OD to protect the source if

the second unit will be installed indoors.

Note: Use standard size Cat5e, Cat6 or Cat6a cables that feature a

wire gauge of 23/24 AWG. Slim category cables are not supported.

Maximum cable distance between two B110-SP-CAT-OD units is

328 ft. (100 m).

Installation

Wireless Access Point

PoE Switch

To LAN

19-11-220-933B57-BOOK.indb 919-11-220-933B57-BOOK.indb 9 2/5/2020 1:28:52 PM2/5/2020 1:28:52 PM

Installation

1. Install a second B110-SP-CAT-OD between the ﬁrst

B110-SP-CAT-OD unit and your source following Equipment

(Edge) Protection Only installation Steps 1-3.

2. In order to protect both the source and edge equipment,

the two B110-SP-CAT-OD units need to be wired cable

end-to-cable end as shown below.

Equipment End

328 ft.

(100 m)

19-11-220-933B57-BOOK.indb 1019-11-220-933B57-BOOK.indb 10 2/5/2020 1:28:52 PM2/5/2020 1:28:52 PM

Table des matières

Langues :

Autres manuels Tripp Lite Parafoudre

Tripp Lite

Tripp Lite ISOBAR8ULTRA Manuel utilisateur

Tripp Lite

Tripp Lite IBAR12/20ULTRA AGIB120V20SSRM Manuel utilisateur

Tripp Lite

Tripp Lite TLM626TEL15 Manuel utilisateur

Tripp Lite

Tripp Lite MT-6PLUS Manuel utilisateur

Tripp Lite

Tripp Lite MT-6PLUS Manuel utilisateur

Tripp Lite

Tripp Lite SUPER7 Manuel utilisateur

Tripp Lite

Tripp Lite HT2210ISOCTR Manuel utilisateur

Tripp Lite

Tripp Lite TLM626 Manuel utilisateur

Tripp Lite

Tripp Lite TLP808TEL Manuel utilisateur

Tripp Lite

Tripp Lite IBAR12/20ULTRA AGIB120V20SSRM Manuel utilisateur

Tripp Lite

Tripp Lite TLP602 Manuel utilisateur

Tripp Lite

Tripp Lite LC 1200 Manuel utilisateur

Tripp Lite

Tripp Lite SPS415HGULTRA Manuel utilisateur

Tripp Lite

Tripp Lite ISOTEL6ULTRA Manuel utilisateur

Tripp Lite

Tripp Lite ISOBAR6 Manuel utilisateur

Tripp Lite

Tripp Lite ISOBAR12ULTRA AGIB120V12SSRM Manuel utilisateur

Tripp Lite

Tripp Lite ISOBAR4ULTRA Manuel utilisateur

Tripp Lite

Tripp Lite SUPER7TEL Manuel utilisateur

Tripp Lite

Tripp Lite Protect It! SK6-6/SPIKEBAR Manuel utilisateur

Tripp Lite

Tripp Lite TR-6FM Manuel utilisateur

Tripp Lite

Tripp Lite SPIKECUBE Manuel utilisateur

Tripp Lite

Tripp Lite DCATV Manuel utilisateur

Tripp Lite

Tripp Lite Protect It! Manuel utilisateur

Tripp Lite

Tripp Lite PM6SN1 Manuel utilisateur

Manuels Parafoudre populaires d'autres marques

ELAC

ELAC ProteK PR91-W Manuel utilisateur

Tsubaki

Tsubaki TSM4000M1 Manuel utilisateur

QVS

QVS PP134C Manuel utilisateur

CyberPower

CyberPower CSP604T Manuel utilisateur

Davis Instruments

Davis Instruments Radio Surge Protector Manuel utilisateur

M-system

M-system MGA-100 Manuel utilisateur

CyberPower

CyberPower CSP706T Manuel utilisateur

CyberPower

CyberPower B300WRC1 Manuel utilisateur

M-system

M-system MGD-24 Manuel utilisateur

Leviton

Leviton 51120-3R Manuel utilisateur

Panamax

Panamax MAX 5400-EX Manuel utilisateur

CyberPower

CyberPower B1006T Manuel utilisateur

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Manuel utilisateur

Minuteman

Minuteman MMS7120RCT Manuel utilisateur

Leviton

Leviton 52412-DS3 Manuel utilisateur

Savio

Savio LZ-07 Manuel utilisateur

Siemens

Siemens HNM3M120 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Manuel utilisateur