Triplett AM200 Manuel utilisateur

User Manual

AM200

Thermo-Anemometer with Wind

Speed, Wind Chill and Temperature

Introduction

Congratulations on your purchase of Triplett AM200 Mini Thermo-

Anemometer. This professional meter, with proper care, will provide

years of safe reliable service.

Meter Description

1. Vane impeller

2. Precision thermistor

3. LCD display

4. POWER and HOLD key

5. UNITS and MODE key

6. Battery compartment (on rear)

7. Swivel handle and storage case

8. Lanyard holder

9. Impeller set screw (on rear of meter)

4. OPERATION

Operation

Select the desired units for air velocity and temperature by

momentarily pressing the UNITS/MODE key from a powered down

condition. The LCD will show temperature units (oC or oF) and Air

Velocity units. Press the UNITS/MODE key repeatedly until the desired

units are displaying. When finished, press the ON/OFF/HOLD key

momentarily to restart the meter with the desired units.

Power the meter by pressing the ON/OFF/HOLD key momentarily.

The Dual Display will illuminate. The top (larger) display indicates

air speed and the lower display indicates temperature.

Position the meter so that the measured airflow enters the meter

vane from the rear of the meter (opposite side from the front panel

logo, part number, etc.).

Activate Data Hold (to freeze the most recent display), by pressing

and holding the ON/OFF/HOLD key while taking measurements. To

return to normal operation, release the key and restart the meter.

Max operation: After a measurement session, press and hold the

UNITS / MODE key until the MAX icon appears on the lower left-hand

side of the LCD. Both the Air Velocity and Temperature indication will

represent the highest readings measured since the meter was last

powered.

Average mode operation: Normally the meter averages readings

every 2 seconds. To select 5, 10 or 13 second averaging, first press

and hold the UNITS/MODE key until the MAX icon appears. Next,

press the key again momentarily and the AVG icon will appear. The

13 second average mode is selected. Now press the key again and

the number 5 will appear. Leave it there if an average of 5 seconds is

desired. Press the key once more for a 10 second average mode. To

return to normal operation press the UNITS/MODE key repeatedly

until all lower left-hand icons disappear.

Wind chill indicator: Press and hold the UNITS/MODE key until the

MAX icon appears. Press the key repeatedly until the WCI icon

appears. The temperature display will now factor in the wind chill. To

return to normal operation, press the UNITS/MODE key again and

the WCI icon will disappear.

AUTO POWER OFF: After approx. 20 mins, if meter keys are not

touched, the meter automatically shuts down to preserve battery

life.

Specifications

General Specifications

Display

Dual LCD with multifunction

indicators

Measurements

Knots, km/h, MPH, ft/min, m/sec, Beaufort force,

windchill,

and temperature (C/F)

Wind-speed

Moving 2 second average with 2 second gust

detect

Sensor

Sapphire bearing, non-corrosive vane for air

velocity and

precision thermistor for

temperature

Average Mode

Choice of 5, 10, or 13 second

average readings

Max Display

Push button highest reading

recall

Data hold

Freeze most recent display

Sample time

1 reading per second

Water-resistant

To 3’ (1 meter)

Min/Max wind-

speed

1.1 to 62.5 MPH

Operating

temperature

5 to 122oF (-15 to 50oC)

Operating humidity

< 80% RH

Power supply

Lithium battery type CR-2032 or

equivalent

Battery life

400 hours approx.

Weight

3 oz. ( 95 g )

Dimensions

Instrument: 5.25 x 2.75 x 0.75” (133 x 70 x 19mm)

Vane: 1” ( 24mm ) diameter

Electrical Specifications

Measurement

Range

Resolution

Accuracy

MPH (Miles per hour)

2.5 to 44.7 MPH

0.2 MPH

± (3%rdg

+0.4MPH)

km/hr (kilometers per

hour)

4.0 to 72.0 km/h

0.7 km/h

± (3%rdg

+1.4km/h)

Knots (nautical miles per

hour)

2.1 to 38.9

knots

0.3 knots

± (3%rdg

+0.6knots)

m/sec (meters per

second)

1.1 to 20.0 m/s

0.01 m/s

± (3%rdg

+0.2m/s)

ft/min (feet per minute)

216 to 3936

ft/min

20ft/min

± (3%rdg

+40ft/min)

Beaufort force

1 to 8 BF

1 BF

± 1

Temperature

0 to 122

0.1

±1.8

-18 to 50

0.1

±1

Maintenance

Battery Replacement

The AM200 has a low battery indicator (battery symbol). Important: Turn the meter off before

opening the battery compartment. Using a coin, turn the battery compartment cover CLOCKWISE

to remove it. Once opened, observe the position of the battery, placing the new one in the same

position. Secure the battery compartment cover and dispose of the lithium battery in accordance

with local, state, or national disposal codes.

All EU users are legally bound by the Battery Ordinance to return all used

batteries to community collection points or wherever batteries / accumulators

are sold.

Disposal in household trash or refuse is prohibited.

Disposal: Follow the valid legal stipulations in respect of the disposal of the device at

the end of its lifecycle

Other Battery Safety Reminders

Never dispose of batteries in a fire. Batteries may explode or leak.

Never mix battery types. Always install new batteries of the same type.

Impeller Replacement

Remove the set screw next to the impeller assembly (on the rear of the meter). Twist the impeller

assembly counter-clockwise to the OPEN position and remove

it.

Install impeller by inserting & twisting the new impeller assembly clockwise Tighten

the set screw.

CFM Measurements

Measure the area of the duct using the diagrams below for rectangular and circular ducts (If the

duct measurements are made in inches, divide the inches by 144 to get the area in square feet).

Plug the area value (in square feet) in the cubic equations below. Note that the air velocity must be

plugged into the cubic equations also.

CFM (ft3/min) = Air Velocity (ft/min) x Area (ft2)

CMM (m3/min) = Air Velocity (m/sec) x Area (m2) x 60

Warranty

Triplett / Jewell Instruments extends the following warranty to the original purchaser of

these goods for use. Triplett warrants to the original purchaser for use that the products

sold by it will be free from defects in workmanship and material for a period of (1) one

year from the date of purchase. This warranty does not apply to any of our products

which have been repaired or altered by unauthorized persons in any way or purchased

from unauthorized distributors so as, in our sole judgment, to injure their stability or

reliability, or which have been subject to misuse, abuse, misapplication, negligence,

accident or which have had the serial numbers altered, defaced, or removed.

Accessories, including batteries are not covered by this warranty

www.triplett.com

Table des matières

Autres manuels Triplett Instrument de mesure

Triplett

Triplett CamView W35 Manuel utilisateur

Triplett

Triplett EPC175 Manuel utilisateur

Triplett

Triplett 60-A Manuel utilisateur

Triplett

Triplett hotwire fox Manuel utilisateur

Triplett

Triplett AM250 Manuel utilisateur

Triplett

Triplett 630 Manuel utilisateur

Triplett

Triplett EM400 Manuel utilisateur

Triplett

Triplett BR260 Manuel utilisateur

Triplett

Triplett 9200B Manuel utilisateur

Triplett

Triplett LT68-NIST Manuel utilisateur

Triplett

Triplett CM200 Manuel utilisateur

Triplett

Triplett MS245 Manuel utilisateur

Triplett

Triplett MS300 Manuel utilisateur

Triplett

Triplett SoniChek MC Manuel utilisateur

Triplett

Triplett BR500 Manuel utilisateur

Triplett

Triplett ET400 Manuel utilisateur

Triplett

Triplett CM1070 Manuel utilisateur

Triplett

Triplett The Hound 2 Manuel utilisateur

Triplett

Triplett CamView IP Pro Manuel utilisateur

Triplett

Triplett Cam View Elite Manuel utilisateur

Triplett

Triplett WQ120 Manuel utilisateur

Triplett

Triplett UTG300 Manuel utilisateur

Triplett

Triplett CM450 Manuel utilisateur

Triplett

Triplett LT80 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur