TriangleTube PGRKIT21 Manuel utilisateur
ELITE and PERFORMANCE
Operating Thermostat Replacement
1
Kit Part Number: PGRKIT21
Included in the Kit:
1- (1) Thermostat
2- (1) Stop Pin Screw
3- (1) Machine Screw
Tools required:
-Wire Cutters
-Screwdriver - #3 Phillips
-Screwdriver - #3 Slotted
-Adjustable Wrench
Indicates a potentially hazardous situation
which, if ignored, can result in serious
injury or substantial property damage.
Indicates special instructions on installa-
tion, operation or maintenance, which are
important to equipment but not related to
personal injury hazards.
NOTICE
WARNING
Failure to follow instructions below can result
in severe personal injury or damage if ignored.
•Instructions are for a qualified installer/ ser-
vice technician.
•Read all instructions before proceeding.
• Follow instructions in proper order.
For your safety, turn off electrical power
supply at service panel before proceeding to
avoid possible electrical shock hazard.
Failure to do so can cause severe personal
injury or death.
WARNINGWARNING
ELITE and PERFORMANCE
Operating Thermostat Replacement
Removal of the Thermostat
1. Disconnect electrical power supply to the
Combination Heater
2. Disengage the top jacket panel from the side
jacket panels using an upward force along the
front edge of the top panel.
3. Remove the front jacket panel by placing a slot-
ted screwdriver between the front panel and the
side jacket panels and using a twist motion.
Use extreme care as not to damage or scratch
the jacket panels with the screwdriver when
removing the front jacket panel.
4. Remove the (4) locking pins along the corners
of the front control panel. On the PERFOR-
MANCE units remove the air inlet mounting
screw along the front edge of the control panel.
5. Lay the front control panel forward to expose
the transformer and control wiring.
6. Using the wire cutters remove any wire ties
along the existing Thermostat capillary tubing.
7. For ease of replacement label or note each wire
and it’s location on the Thermostat prior to
removal of any wire leads.
8. Remove the wire leads from the Thermostat ter-
minals using pliers to prevent damage to the
wire leads.
9. Use a slotted screwdriver to remove the knob
from the Thermostat.
10. Use a #3 Phillips screwdriver to remove the left
Thermostat mounting screw.
11. Use a slotted screwdriver to remove the “stop
pin” mounting screw. The Thermostat can now
be remove from the backside of the front con-
trol panel.
12. Remove the sensing bulb from the drywell
locations.
- The Secondary (domestic) thermostat sens-
ing bulb is located in a drywell at the
domestic hot water outlet.
- The Primary (space heating) thermostat
sensing bulb is located in a drywell in front
of the domestic cold water inlet.
Installation of the Thermostat
1. Insert the new sensing bulb into the same loca-
tion as the existing bulb. Ensure the bulb is
position at the bottom of the drywell.
2. Mount the new Thermostat onto the front con-
trol panel through the backside of the panel.
Ensure the terminals of the Thermostat are ori-
entated downward.
3. Position the indication ring onto the front con-
trol panel so the indication mark is at the top of
the ring. See Fig. 1
4. Use the mounting screws to secure the
Thermostat and indicator ring to the front con-
trol panel using the Phillips screw and the “stop
pin” slotted screw. Ensure the “stop pin” screw
is position to the right. See Fig. 1
5. Turn the Thermostat stem counter-clockwise
fully and re-insert the knob.
6. Attach the wire leads to the Thermostat termi-
nals in the proper order. Ensure all leads are
securely attached to the terminals.
7. Re-install the front control panel using the lock-
ing pins to secure the panel into place.
NOTICE
2
ELITE and PERFORMANCE
Operating Thermostat Replacement
2002-64 Elite &Performance Operating Thermostat Repl.
07/02
To prevent potential damage to the unit
and/or electrial shock hazard ensure the cap-
illary tubes of the operating aquastats are
tucked up under the front control panels and
not lying across any wire terminals.
8. Reattach the top jacket panel by aligning and
engaging the panel onto the locking pins.
9. Reattach the front jacket panel by inserting the
lower tabs into the side jacket panels and then
engaging the upper locking pins.
10. Reconnect the power supply and return the unit
to service.
WARNING
Operating
Thermostat
Wire
Connections
Indication
Mark
Bezel
Machine
Screw
Stop Pin
Screw
Fig. 1
Autres manuels TriangleTube Thermostat
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
