TRENDnet TE100-S1616 Manuel utilisateur

TE100-S1616/S2424/S3232

16/24/32-port

10/100M NWay

Fast Ethernet Switch

User’s Guide

FCC Warning

This equipment has been tested and found to comply with

the regulations for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with this

user’s guide, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in

which case the user will be required to correct the

interference at his own expense.

CE Mark Warning

This is a Class B product. In a domestic environment, this

product may cause radio interference, in which case the user

may be required to take adequate measures.

P/N:6012-1001600

TABLE OF CONTENTS

ABOUT THIS GUIDE..............................................................................III

PURPOSE.....................................................................................................III

TERMS/USAGE ...........................................................................................III

OVERVIEW OF THIS USER’S GUIDE.........................................................IV

INTRODUCTION.......................................................................................1

FAST ETHERNET TECHNOLOGY.................................................................1

SWITCHING TECHNOLOGY.........................................................................2

FEATURES.....................................................................................................3

UNPACKING AND INSTALLATION..................................................7

UNPACKING..................................................................................................7

INSTALLATION.............................................................................................7

100BASE-FX MODULE INSTALLATION....................................................8

RACK MOUNTING........................................................................................9

IDENTIFYING EXTERNAL COMPONENTS ...............................11

FRONT PANEL............................................................................................11

REAR PANEL..............................................................................................13

LED INDICATORS......................................................................................14

CONNECTING THE SWITCH...........................................................15

PC TO SWITCH...........................................................................................15

HUB TO SWITCH.........................................................................................16

A. 10BASE-T Hub.................................................................................16

B. 100BASE-TX Hub............................................................................16

HUB WITHOUT UPLINK (MDI-II) PORT ..................................................17

A. Using straight cable........................................................................17

B. Using crossover cable....................................................................17

SWITCH TO SWITCH (OTHERDEVICES)...................................................17

A. Using straight cable........................................................................17

B. Using crossover cable....................................................................17

PORT SPEED & DUPLEXMODE...............................................................18

TECHNICAL SPECIFICATIONS ......................................................19

RJ-45 PIN SPECIFICATION...............................................................21

iii

ABOUT THIS GUIDE

Congratulations on your purchase of the 16/24/32-port

10/100M NWay Fast Ethernet Switch. This device integrates

100Mbps Fast Ethernet and 10Mbps Ethernet network

capabilities in a highly flexible package.

Purpose

This guide discusses how to install your 16/24/32-port

10/100M NWay Fast Ethernet Switch.

Terms/Usage

In this guide, the term “Switch” (first letter upper case)

refers to your 16/24/32-port 10/100M NWay Fast Ethernet

Switch, and ”switch” (first letter lower case) refers to other

Ethernet switches.

This guide provides the information you need to install and

configure the following models of the Switch:

?? 16-port 10/100M NWay Fast Ethernet Switch

?? 24-port 10/100M NWay Fast Ethernet Switch

?? 32-port 10/100M NWay Fast Ethernet Switch

The functionality of three units is identical, except for the

number of ports. Where appropriate, differences between the

two units are noted.

Overview of this User’s Guide

Chapter 1, Introduction. Describes the Switch and its

features.

Chapter 2, Unpacking and Installation. Helps you get

started with the basic installation of the Switch.

Chapter 3, Identifying External Components. Describes the

front panel, rear panel and LED indicators of the Switch.

Chapter 4, Connecting the Switch. Tells how you can

connect the Switch to your Ethernet network.

Appendix A, Technical Specifications. Lists the technical

(general, physical and environmental, and performance)

specifications of the Switch.

Appendix B, RJ-45 Pin Specification. Describes the RJ-45

receptacle/connector and the straight and crossover cable

connector.

INTRODUCTION

This chapter describes the features of the Switch and some

background information about Ethernet/Fast Ethernet

switching technology.

Fast Ethernet Technology

The growing importance of LANs and the increasing

complexity of desktop computing applications are fueling the

need for high performance networks. A number of high-speed

LAN technologies have been proposed to provide greater

bandwidth and improve client/server response times. Among

them, 100BASE-T (Fast Ethernet) provides a non-disruptive,

smooth evolution from the current 10BASE-T technology.

The non-disruptive and smooth evolution nature, and the

dominating potential market base, virtually guarantee cost

effective and high performance Fast Ethernet solutions in

the years to come.

100Mbps Fast Ethernet is a new standard specified by the

IEEE 802.3 LAN committee. It is an extension of the

10Mbps Ethernet standard with the ability to transmit and

receive data at 100Mbps, while maintaining the CSMA/CD

Ethernet protocol. Since the 100Mbps Fast Ethernet is

compatible with all other 10Mbps Ethernet environments, it

provides a straightforward upgrade and takes advantage of

the existing investment in hardware, software, and

personnel training.

Switching Technology

Another approach to pushing beyond the limits of Ethernet

technology is the development of switching technology. A

switch bridge Ethernet packets at the MAC address level of

the Ethernet protocol transmitting among connected

Ethernet or Fast Ethernet LAN segments.

Switching is a cost-effective way of increasing the total

network capacity available to users on a local area network.

A switch increases capacity and decreases network loading

by dividing a local area network into different segments,

which don’t compete with each other for network

transmission capacity.

The switch acts as a high-speed selective bridge between the

individual segments. The switch, without interfering with

any other segments, automatically forwards traffic that

needs to go from one segment to another. By doing this the

total network capacity is multiplied, while still maintaining

the same network cabling and adapter cards.

For Fast Ethernet networks, a switch is an effective way of

eliminating problems of chaining hubs beyond the “two-

repeater limit.” A switch can be used to split parts of the

network into different collision domains, making it possible

to expand your Fast Ethernet network beyond the 205-meter

network diameter limit for 100BASE-TX networks. Switches

supporting both traditional 10Mbps Ethernet and 100Mbps

Fast Ethernet are also ideal for bridging between the

existing 10Mbps networks and the new 100Mbps networks.

Switching LAN technology is a marked improvement over

the previous generation of network bridges, which were

characterized by higher latencies. Routers have also been

used to segment local area networks, but the cost of a router,

the setup and maintenance required make routers relatively

impractical. Todayswitches are an ideal solution to most

kinds of local area network congestion problems.

Features

The Switches were designed for easy installation and high

performance in an environment where traffic on the network

and the number of user increase continuously.

The Switches with its rack size is specifically designed for

middle to large workgroups. These Switches provide

immediate access to a rapidly growing network through a

wide range of user-reliable functions.

The Switches are ideal for deployment with multiple high-

speed servers for shared bandwidth 10Mbps or 100Mbps

workgroups. With the highest bandwidth 200Mbps (100Mbps

full-duplex mode), any port can provide workstations with a

congestion-free data pipe for simultaneous access to the

server.

The Switches are expandable by cascading two or more

switches together. As all ports support 200Mbps, the

Switches can be cascaded from any port and to any number

of switches.

The Switches are a perfect choice for site planning to

upgrade to Fast Ethernet in the future. Ethernet

workgroups can connect to the Switches now, and change

adapters and hubs anytime later without needing to change

the Switches or reconfigure the network.

The Switches combine dynamic memory allocation with

store-and-forward switching to ensure that the buffer is

effectively allocated for each port, while controlling the data

flow between the transmit and receive nodes to guarantee

against all possible packet loss.

The Switches are an unmanaged 10/100 Fast Ethernet

Switch that offers solutions in accelerating small Ethernet

workgroup bandwidth. Other key features are:

Uplink/ MDI-II (media dependent interface) port for uplink

to another switch or hub.

Store and forward switching scheme capability. As the

result of complete frame checking and error frame filtering,

this scheme prevents error packages from transmitting

among segments.

NWay Auto-negotiation for any port. This allows for auto-

sensing of speed (10/100Mbps) thereby providing you with

automatic and flexible solutions in your network

connections.

Flow control for any port. This minimizes dropped packets

by sending out collision signals when the port’s receiving

buffer is full. Note that flow control is only available in half

duplex mode.

Data forwarding rate per port is at wire-speed for 100Mbps

Autres manuels pour TE100-S1616

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TRENDnet Changer

TRENDnet

TRENDnet TK-801R Manuel utilisateur

TRENDnet

TRENDnet TE100 S800i Manuel utilisateur

TRENDnet

TRENDnet TPE-80WS - Web Smart PoE Switch Manuel utilisateur

TRENDnet

TRENDnet TEG-S2400I - DATA SHEETS Manuel d'installation et d'exploitation

TRENDnet

TRENDnet TE100-S50g Manuel utilisateur

TRENDnet

TRENDnet TE100-DX5Eplus Manuel utilisateur

TRENDnet

TRENDnet TK-205i Manuel utilisateur

TRENDnet

TRENDnet TPE-S44 - Switch Manuel d'installation et d'exploitation

TRENDnet

TRENDnet TE100-DX4PCI Manuel utilisateur

TRENDnet

TRENDnet TEG-S80TX Manuel utilisateur

TRENDnet

TRENDnet TEG-2248WS - Gigabit Web Smart Switch Manuel utilisateur

TRENDnet

TRENDnet TK-205i Manuel utilisateur

TRENDnet

TRENDnet TE100 S5Pplus Manuel utilisateur

TRENDnet

TRENDnet TEG-S41SX Manuel utilisateur

TRENDnet

TRENDnet TK-1604R Manuel utilisateur

TRENDnet

TRENDnet TE100-SK2 Manuel utilisateur

TRENDnet

TRENDnet TE100-S16D Manuel utilisateur

TRENDnet

TRENDnet TK-209K Manuel utilisateur

TRENDnet

TRENDnet TEG-S224TXA - 26PORT Gigabit Copper Switch 24-10/100... Manuel utilisateur

TRENDnet

TRENDnet TE-800plus Manuel utilisateur

TRENDnet

TRENDnet 21000BASE-T Manuel utilisateur

TRENDnet

TRENDnet TPE-TG44G Manuel utilisateur

TRENDnet

TRENDnet TK-803R Manuel utilisateur

TRENDnet

TRENDnet TPE-T88G Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur