TRENDnet TE100-DX4PCI Manuel utilisateur

Ethernet Card for PCI

TE100-DX4PCI

10/100 Mbps

Fast Ethernet Hub Card

for PCI

Auto-Congurable

User's Guide

Ethernet Card forPCI

FCC Compliance Statement

This device complies with Part 15 of the FCC rules. Operation

is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation.

NOTE

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

This Class B digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Requlations.

Cet appareil numérique de la Classe B respecte toutes

les exigences du Réglement sur le matériel brouilleur du

Canada.

All registered trademarks are the property of their respective

Ethernet Card for PCI

CONTENTS

FCC Compliance Statement ........................ 1

Section 1 Introduction .................................... 4

Section 2 Installation ..................................... 5

Section 3 Conguration and Diagnostics .... 6

Section 4 Drivers Installation ...................... 7

Section 5 Cable Specications ..................... 8

Section 6 Troubleshooting ............................. 9

Section 7 Specications ................................. 10

Section 8 LED Indication ............................... 11

Ethernet Card forPCI

Section 1 Introduction

Your Ethernet hub card is a high performance network

device that is designed to easily link four 10/100Mbps

hub with a 100Mbps PCI interface card. The hub

card

consists of four (4) 10/100BASE-TX hub port to

linking and forwartding packets in one segment, it also

includes a 32-bit PCI interface to provide an additional

connection with the network segment.

The Ethernet hub card is designed for plug-and-play

installation and easy managements with all

10/100Mbps ports and LEDs on the bracket.

Summary of features

• Compliant with the 10BASE-T, 100BASE-TX

specication of the IEEE 802.3 standard

• All 10/100Mbps hub port supports auto-negotia

tion and ato-detection for 10 or 100Mbps

• Equipped with four LEDs for easy viewing and

troubleshooting

• Equipped with a 100Mbps MAC interface to pro

vides a connection with the 10/100Mbps

hub seg ment

• Diagnostic software and network drivers on the

diskette

• 32-bit bus mastering for high throughput and

low

processor utilization

Ethernet Card for PCI

Section 2 Installation

This section describes how to install your Ethernet

hub card. Perform the following steps to install the

adapter.

1. Turn off your computer and all peripherals.

2. Make a note of the cables and cords that are

connected to the computer and disconnect them.

3. Remove your personal computer's cover (refer to

the owner's manual of your personal computer).

4. Select any available PCI slot, and remove the

slot cover.

5. Carefully install the Ethernet hub card into the

ex-pansion slot by rmly pressing the card into

the edge of the connector slot until the card is

snugly seated in the expansion slot and fasten

the retaining bracket with screw from the slot

cover.

6. Reinstall your personal computer's cover and

re-connect the power cord and all cables.

7. Connect the Ethernet cable to your personal

computer.

Note:

System Requirements:

A PC and BIOS that support the PCI Local Bus

Ethernet Card forPCI

Specication 2.x.

Section 3 Conguration and Diagnostics

Your Ethernet hub card has built-in a 100Mbps MAC

interface which is automatically configured when

you power-up your computer, In certain computers,

however, you must modify your BIOS by entering

your CMOS SETUP utility.

To view the configuration parameters assigned by

the BIOS, boot the computer to DOS, insert the

diskette into the oppy drive and then execute the utility

software EZRTS.EXE in the CONFIG directory.

Ethernet Card for PCI

Section 4 Drivers Installation

Be sure to install the proper driver for the hub card

to provides a connection between the 100Mbps MAC

interface and the four 10/100Mbps nodes.

You can use the drivers supplied by the software

diskette that is compatible with your Networking

Operating System. The driver for each Networking

Operating System is under a separate directory. Each

directory includes a README.TXT le to describe

the detailed installation procedure. A RELEASE.TXT

le under root directory lists the information of all

the available drivers.

Ethernet Card forPCI

Section 5 Cable Specications

The Ethernet adapter is equipped with four

RJ-45 connectors, the RJ-45 connector requires a

corrsponding cable. This section describes each

cable's specication.

• Cable for RJ-45 connector for 10Mbps network

Cable type: UTP with 2

twisted pairs o f

22, 24 or 26 AWG

Category: 3, 4, or 5

Twists per foot: 2 to 3(min.)

Nominal impedance: 100 ohms

Maximum cable length: 300'(100m)

Maximum Attenuation: 8 to 10 dB per 100m

at 10Mz

• Cable for RJ-45 connector for 100Mbps network

Cable type: UTP with 2

twisted pairs of 2 6

AWG

Category: 5

Twists per foot: 2 to 3(min.)

Nominal impedance: 100 ohms

M20082217500

Ethernet Card for PCI

Maximum cable length: 300'(100m)

Section 6 Troubleshooting

This section describes reasons for some adapter's

failures

and the actions to be taken to resolve the problems.

• PCI scan specied, device not found

Action: Verify that the PCI Ethernet adapter is

physically installed properly. Otherwise,

install the card in a different PCI

slot or replace the adapter.

• Connection failure if using an unshielded twisted

M20082217500

Ethernet Card forPCI

pair (UTP) cable

Action: Verify that the UTP cable

is rmly attached

and the cable type is correct for use.

Section 7 Specications

IEEE 802.3 Standard: 10BASE-T

100BASE-TX

Wiring Connector: RJ-45

Bus Characteristics: 32 bits ; PCI Local Bus

specication 2.x

I/O address: being assigned by the

BIOS to a free I/O address

block

IRQ line: INTA ; being assigned

by the BIOS to a free IRQ

(interrupt) number

Autres manuels pour TE100-DX4PCI

Table des matières

Autres manuels TRENDnet Changer

TRENDnet

TRENDnet TEG-40080ES Manuel utilisateur

TRENDnet

TRENDnet TEG-S50TXE SHEETS Manuel utilisateur

TRENDnet

TRENDnet TEG-448WS - Switch Manuel utilisateur

TRENDnet

TRENDnet TK-401R Manuel utilisateur

TRENDnet

TRENDnet TE100 S55Eplus Manuel utilisateur

TRENDnet

TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manuel utilisateur

TRENDnet

TRENDnet TE100-S16Eplus Manuel utilisateur

TRENDnet

TRENDnet TK-205i Manuel utilisateur

TRENDnet

TRENDnet TEG-2248WS - Gigabit Web Smart Switch Manuel utilisateur

TRENDnet

TRENDnet TE100-S22 Manuel utilisateur

TRENDnet

TRENDnet TEG-S16R - DATA SHEETS Manuel utilisateur

TRENDnet

TRENDnet TE100-S2424 Manuel utilisateur

TRENDnet

TRENDnet TEG-448WS - Switch Manuel utilisateur

TRENDnet

TRENDnet TK-240DP Manuel utilisateur

TRENDnet

TRENDnet TE100-H24R Manuel utilisateur

TRENDnet

TRENDnet TEG-S28TX Manuel utilisateur

TRENDnet

TRENDnet TEG-S5g - Gigabit GREENnet Switch Manuel utilisateur

TRENDnet

TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manuel utilisateur

TRENDnet

TRENDnet TO-PG541 Manuel utilisateur

TRENDnet

TRENDnet TPE-S44 - Switch Manuel utilisateur

TRENDnet

TRENDnet TEG-S224TXA - 26PORT Gigabit Copper Switch 24-10/100... Manuel utilisateur

TRENDnet

TRENDnet TEG-7080ES Manuel utilisateur

TRENDnet

TRENDnet TE100-S1212 Manuel utilisateur

TRENDnet

TRENDnet TPE-1620WS Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur