Travis Industries 1250 Insert Manuel utilisateur

1 2 5 0 W o o d I n s e r t

Owner's Manual

• Masonry Fireplace Insert • Zero-Clearance (Metal)

Fireplace Insert

Save these instructions

for future reference

AFETY NOTICE:

If this appliance is not properly installed, a house fire may

result. For your safety, follow the installation directions.

Contact local building or fire officials about restrictions and

installation inspection requirements in your area.

Travis Industries, Inc.

48 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

www.travisproducts.com

 Copyright 2 9, T.I.

$1 . 1 - 1233_

4 9 819 Tested to:

U.L. 1482 and ULC S628-M93

2 Introduction

Introduction

We welcome you as a new owner of a 125 wood-burning fireplace insert. In purchasing a 125 you

have joined the growing ranks of concerned individuals whose selection of an energy system reflects both

a concern for the environment and aesthetics. The 125 is one of the finest appliances the world over.

This manual will explain the installation, operation, and maintenance of this appliance. Please familiarize

yourself with the Owner's Manual before operating your appliance and save the manual for future

reference. Included are helpful hints and suggestions which will make the installation and operation of

your new appliance an easier and more enjoyable experience. We offer our continual support and

guidance to help you achieve the maximum benefit and enjoyment from your appliance.

Important Information

No other 125 appliance has the same serial number

as yours. The serial number is stamped onto the label

on the back of the appliance.

This serial number will be needed in case you require

service of any type.

Model: 125 Insert

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

48 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

ave Your Bill of ale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Table of Contents 3

General Information

Introduction ......................................................2

Important Information .........................................2

Safety recautions.............................................4

Features & Specifications ....................................6

Fireplace Insert Installation

lanning The Installation .....................................7

Preparation for Installation ..............................7

Additional Accessories Needed for Installation ....7

Installation Considerations..............................7

Fireplace Requirements ......................................8

Insert lacement Requirements ............................8

Masonry Fireplace Requirements..........................9

Zero-Clearance (Metal) Fireplace Requirements ......9

Hearth Requirements .........................................10

Drafting erformance .........................................10

Leveling Bolt Installation......................................10

Block-Off late Installation...................................11

Insert with ositive Connection .............................12

Insert with Direct Connection (Masonry Fireplace) ....12

Insert with Direct Connection (Z.C. Fireplace) ..........13

Insert with Face Seal Connection ..........................13

Operating Your Appliance

Safety Notice: ...................................................14

Before Your First Fire .........................................14

Opening the Door ..............................................15

Starting a Fire ...................................................16

Adjusting the Burn Rate ......................................17

Ash Removal ....................................................17

Optional Blower Operation...................................18

Re-Loading the Stove .........................................18

Overnight Burn..................................................18

Normal Operating Sounds ...................................18

Hints for Burning................................................19

Selecting Wood .................................................19

Troubleshooting ................................................20

Maintaining Your Appliance

Daily Maintenance (while stove is in use) ................21

Remove Ash (if necessary)..............................21

Clean the Glass (if necessary) .........................21

Monthly Maintenance (while appliance is in use).......22

Door and Glass Inspection ..............................22

Creosote - Formation and Need for Removal ......2

Yearly Maintenance............................................23

Touch Up Paint.............................................23

Cleaning the Air Duct and Blower (if applicable)...23

Firebrick and Baffle Inspection .........................23

Door arts ........................................................24

Firebox arts ....................................................25

Floor and Side Firebrick Removal & Replacement 25

Baffle Removal & Replacement.............................26

Air Tube Removal & Replacement .........................26

Warranty

Warranty ..........................................................27

Listing Information

Listing Label .....................................................29

Optional E uipment

Surround anels ................................................30

Front Blower (part # 99000128).............................32

Index

Index ...............................................................34

4 Safety Precautions

The viewing door must be

closed and latched during

o eration.

Never block free airflow through

the air vents on this a liance.

Gas

Gasoline or other flammable

liquids must never be used to

start the fire or "Freshen U " the

fire. Do not store or use

gasoline or other flammable

liquids in the vicinity of this

a liance.

This a liance is designed and

a roved for the burning of cord

wood only. Do not attem t to

burn any other ty e of fuel other

than cord wood in this

a liance, it will void all

warranties and safety listings.

ASHES

Ashes must be dis osed in a

metal container with a tight lid

and laced on a non-

combustible surface well away

from the home or structure.

Do not touch the a liance while

it is hot and educate all children

of the danger of a high-

tem erature a liance. Young

children should be su ervised

when they are in the same room

as the a liance.

36"

Kee furniture, dra es, curtains,

wood, a er, and other

combustibles a minimum of 36"

away from the front of the

a liance.

This a liance must be ro erly

installed to revent the

ossibility of a house fire. The

instructions must be strictly

adhered to. Do not use

makeshift methods or

com romise in the installation.

Contact your local building

officials to obtain a ermit and

information on any installation

restrictions or ins ection

requirements in your area.

Notify your insurance com any

of this a liance as well.

Ins ect the chimney connector

and chimney at least twice

monthly and clean if necessary.

Creosote may build u and

cause a house fire.

Do not connect this a liance to

any chimney serving another

a liance.

Type

HT Clay

Liner

This a liance must be

connected to a listed high

tem erature (UL 103 HT)

residential ty e chimney or an

a roved masonry chimney with

a standard clay tile, or stainless

steel liner.

Safety Precautions 5

Mobile

Home

When installed in a mobile

home, this a liance must be

bolted to the floor, have outside

air, and not be installed in the

bedroom (Per H.U.D.

requirements). Check with local

building officials.

Do not lace clothing or other

flammable items on or near this

a liance.

Never try to re air or re lace

any art of this a liance unless

instructions are given in this

manual. All other work must be

done by a trained technician.

Do not make any changes or

modifications to an existing

masonry fire lace or chimney to

install this a liance.

Do not make any changes to the

a liance to increase

combustion air.

Allow the a liance to cool

before carrying out any

maintenance or cleaning. Overfiring the a liance may

cause a house fire. If a unit or

chimney connector glows, you

are overfiring.

Maintain the door and glass seal

and kee them in good

condition.

Avoid lacing wood against the

glass when loading. Do not

slam the door or strike the glass.

Do not use a grate or other

device to elevate the fire off of

the firebox floor. Burn the fire

directly on the bricks.

This

Manual

Do not throw this manual away.

This manual has im ortant

o erating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Travis Industries, Inc. grants

no warranty, implied or

stated, for the installation or

maintenance of your

appliance, and assumes no

responsibility of any

consequential damage s).

6 Features & Specifications

Installation Options:

• Masonry Fire lace Insert

• Zero-Clearance (Metal) Fire lace Insert

Features:

• EPA Phase II A roved

• 1.6 Cubic Foot Firebox Volume

• Single O erating Control

• Acce ts Logs U to 18" Long

• Steel Plate Construction (1/4" & 3/16")

• Heavy Duty Refractory Firebrick

• O tional High-Tech Blower

Heating Specifications:

A roximate Maximum Heating Ca acity (in square feet)* 750 to 1,200

Maximum BTU's er Hour (Cord Wood Calculation) 66,800

Maximum Burn Time U to 8 Hours

* Heating ca acity will vary de ending on the home's floor lan, degree of insulation, and the outside

tem erature. It is also affected by the quality and moisture level of the fuel.

Dimensions:

13-1/2"

Note:

Measure side, corner,

and back clearances

from the stove top. 5-7/8"

20"

23-5/8"

18-5/8"

Figure 1

Emissions:

4.4 Grams Per Hour (EPA Phase II A roved) – Tests conducted by E.E.S.P.C.

8 Stove Installation for qualified installers only)

Fireplace Requirements

Figure 2 shows the minimum size requirements for the ty e of fire lace used.

Masonry

Fireplace Z.C. (Metal)

Fireplace

Minimum Fireplace Size

Height (front)

Height (rear)

Width (front)

Width (rear)

Depth

Hearth Depth*

Hearth Width

Facing Width

Facing Height

Mantel Height

20-3/4"

23-5/8"

13-1/2"

19"

39-5/8"

42-5/8"

32"

35-1/2"

* This is the distance the insert protrudes from

the fireplace opening plus the required 16" of

hearth extension in U.S.A. (18" in Canada).

Non-Combustible Hearth

Combustible Mantel

Non-Combustible Facing

20-3/4"

25-5/8"

14-1/2"

19"

39-5/8"

47-5/8"

32"

44"

Figure 2

Insert Placement Requirements

• The insert must be laced so that no combustibles are within, or can swing within (e.g. dra es, doors), 36" of the

front of the insert

• Insert and hearth must be installed on a level, secure floor

• The minimum clearances, facing, and hearth requirements in Figure 3 must be met (follow the clearances for the

ty e of fire lace being used - either masonry or zero-clearance).

AAAAAAAAAAAAA

AAAAAAAAAAAAAA

Side

Wall

Combustible Mantel

Combustible Top Facing

Non-Combustible

Hearth

Facing

Masonry

Fireplace

Minimum Clearances

Sidewall to Insert

Side Facing

Top Facing

Mantel to Insert

Hearth (Front)*

Hearth (Side)

Front of Insert

Extension onto Hearth

13"

9-1/2"

12"

15-1/2"

16" **

36"

* Does not include the distance the insert

extends onto the hearth (dimension "x").

ZC (Metal)

Fireplace

30"

12"

24"

16" ** (** 18" in Canada)

36"

Figure 3

10 Stove Installation for qualified installers only)

Hearth Requirements

• Must extend 16" in front of the insert (18" in Canada) and 8" on both sides (min. 26" dee by 40-1/4" wide)

• Must be non-combustible and at least .018" thick (26 gauge)

Drafting Performance

This a liance relies u on natural draft to o erate. External forces, such as wind, barometric ressure, to ogra hy,

or factors of the home (negative ressure from exhaust fans, chimneys, air infiltration, etc.), may adversely affect

draft. Travis Industries can not be res onsible for external forces leading to less than o timal erformance.

Leveling Bolt Installation

Two leveling bolts are included to level the insert if the fire lace has a ste ed-u hearth. To install, raise

the rear of the insert u and insert the leveling bolts into the holes in the rear corners of the insert. Adjust

the bolts until they extend the same height as the hearth ste s u . After the insert is installed, fine-tune

the leveling bolts to level the insert.

AAA

This distance is the

hearth step-up. The

leveling bolts should

stick out this far from the

base of the insert. Fireplace

Hearth

The leveling bolts go

into the holes at the

rear corners of the

insert.

Figure 5

Autres manuels pour 1250 Insert

Table des matières

Autres manuels Travis Industries Cheminée intérieure

Travis Industries

Travis Industries Xtreme 6020 Manuel utilisateur

Travis Industries

Travis Industries DVL Insert Manuel utilisateur

Travis Industries

Travis Industries 864 ST GS Manuel utilisateur

Travis Industries

Travis Industries 616 GSR2 Insert Manuel utilisateur

Travis Industries

Travis Industries 564 Manuel utilisateur

Travis Industries

Travis Industries Xtreme 6020 Manuel utilisateur

Travis Industries

Travis Industries 42 ProBuilder GSB2 Manuel utilisateur

Travis Industries

Travis Industries DVS GSR Ember-Fyre Manuel utilisateur

Travis Industries

Travis Industries Medium Flush Wood Hybrid Fyre Insert Manuel utilisateur

Travis Industries

Travis Industries 864 Clean Face GSR2 Manuel utilisateur

Travis Industries

Travis Industries 864 TRV Manuel utilisateur

Travis Industries

Travis Industries 864 TRV GS2 Manuel utilisateur

Travis Industries

Travis Industries 6015 HO GSR2 Manuel utilisateur

Travis Industries

Travis Industries 4415 HO ST Manuel utilisateur

Travis Industries

Travis Industries DVS EF Fireplace Manuel utilisateur

Travis Industries

Travis Industries DVS FIREPLACE Manuel utilisateur

Travis Industries

Travis Industries 430 GSR2 Manuel utilisateur

Travis Industries

Travis Industries Flush Wood Plus Manuel utilisateur

Travis Industries

Travis Industries 36 CF II Manuel utilisateur

Travis Industries

Travis Industries 864 TRV Deluxe Manuel utilisateur

Travis Industries

Travis Industries Fireplace Xtrordinair 864 Deluxe Manuel utilisateur

Travis Industries

Travis Industries Pro Builder42 Linear Manuel utilisateur

Travis Industries

Travis Industries 616 Diamond-Fyre GSR Manuel utilisateur

Travis Industries

Travis Industries 35 CB Australian Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation