Transition Networks E-CX-MC01B Manuel utilisateur

Universal Coax

10Base2

Micro-ceiver

The Ethernet10Base2 Micro-ceiver (transceiver) provides a simple and inexpensive means for

connecting to your Ethernet network. The Universal Micro-ceiver, part number E-CX-MC01(B), is

a 10Base2 thin coaxial transceiver (AUI to BNC)

INSTALLATION INSTRUCTIONS

Connecting the Coax Micro-ceiver to the Network:

First connect the Micro-ceiver to the AUI port on the Ethernet card or repeater (Note: The Micro-

ceiver can be attached to an AUI cable which is connected to a card or repeater, maximum AUI

cable distance is 50 meters or 165 feet). In a thin coax installation the next step is to insert a coax

BNC "T" connector, (not provided) onto the female end of the Micro-ceiver. DO NOT use a coax

segment directly from the Micro-ceiver either to another card or to the BNC "T", this can cause

excessive faults on your network and is not recommended. Using the BNC "T" you can now

connect directly to the thin coax network either at the end of the segment or in the middle.

The following installation criteria must be met:

- For a thin coax segment the cable must not exceed 185 meters or 606 feet

- Be sure the SQE switch is in the correct position for the application

- Not more than 30 Micro-ceivers can be placed on a segment

- The Micro-ceivers must be placed at least 0.5 meters apart

- The coax segment must be terminated at each end with a 50 ohm terminator

- Make sure that all of the connections are properly latched before starting up the device(s)

When connecting the Micro-ceiver to a hub or repeater, the SQE switch must be in the OFF

position. When connecting the Micro-ceiver to an Ethernet card or workstation, the SQE switch

must be in the ON position.

SQE

Heartbeat On Off

TRANSITIO

ENGINEERING,

INC.

Ethernet™

10Base 2/5

Transceiver

#E-CX-MC01

Mpls., Mn 55344

SQE Enabled

Power

BNC (female)

AUI (DB-15)

SQE Heartbeat: Enable - The SQE switch should be enabled (ON) when the Universal

Micro-ceiver is connected to a DTE or workstation.

Disable - The SQE switch should be disabled (OFF) when connected to

the AUI port of an Ethernetrepeater such as the model 1003 10BaseT hub.

FCC APPROVAL: This equipment has been tested and found to comply with the limits for a class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. this equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference, in which case, the user will be required to correct the interference at his own expense.

Minneapolis, MN 55344 USA

phone 612-941-7600 toll free 800-LAN-WANS (800-526-9267)

fax 612-941-2322 bulletin board 612-941-9304

[email protected] [email protected]

toll free tech support USA 800-260-1312 7312.B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Transition Networks Émetteur-récepteur

Transition Networks

Transition Networks FAST ETHERNET E-TX-MC01 Manuel utilisateur

Transition Networks

Transition Networks E-FRL-MC01A Manuel utilisateur

Transition Networks

Transition Networks E-TBT-MC05 Manuel utilisateur

Transition Networks

Transition Networks TN-GB-ESX5 Manuel utilisateur

Transition Networks

Transition Networks ETHERNET E- FL/RED-MC01(SMA) Manuel utilisateur

Transition Networks

Transition Networks TN-CWDM-SFP-1xx0 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-MC04 Manuel utilisateur

Transition Networks

Transition Networks E-CX-MC02 Manuel utilisateur

Transition Networks

Transition Networks TN-SFP-10G Series Manuel utilisateur

Transition Networks

Transition Networks E-FX-MC01 Manuel utilisateur

Transition Networks

Transition Networks TN-SFP-ELX1 Manuel utilisateur

Transition Networks

Transition Networks E-FRL-MC05 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-MC03 Manuel utilisateur

Transition Networks

Transition Networks Micro-ceiver E-FRL-MC01C Manuel utilisateur

Transition Networks

Transition Networks E-TBT-MC05 Manuel utilisateur

Transition Networks

Transition Networks ETHERNET E-TBT-MC01(LC) Manuel utilisateur

Transition Networks

Transition Networks E-FRL-MC03 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-MCO1 Manuel utilisateur

Transition Networks

Transition Networks E-CX-MC22 Manuel utilisateur

Transition Networks

Transition Networks E-FRL-MC04 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur