Trane THS04 Manuel utilisateur

RT-SVU010B-GB

User Guide

THS04

wall thermostat

1.Wiring

Please refer to wiring diagram for details

a. Bus

Communication between CH536 and THS04 is done by Modbus on RS485.

On CH536 a bus is dedicated to that communication: J9 FBus1

This is based on three wires: plus ; minus ; reference (circle)

Vout is not used. (cf Figure.1)

Figure 1

On THS04, those three signals are: Rx+/Tx+ ; Rx-/Tx-; GND (cf Figure.2)

Figure 2

b. Power supply

In addition to communication signals, THS04 requires power supply.

X201 to be connected to GND of THS04

X200 to be connected to 24V~ of THS04

2. Display

Figure 3

Display is splitted in different areas, providing information about:

1. Unit mode (Heat, Cool, Auto). We can have combination of symbols Auto+Cool or Auto+Heat

indicating the actual running status

2. Zone Temperature

3. Fan mode (On, Auto).

4. Fan speed (min, intermediate, nominal)

6. Key on: logged as user

7. Set on: modification of temperature setpoint (will be taken in account when Set switches off)

9. Occupancy of current Timeband (scheduler)

10. Current day

11. Unit status: Alarm, Compressors On/Off, Indoor Fans On/Off, Auxiliary Heating On/Off

12. “hh:mm” (time) if unit is in local control.

“BAS” if unit is controlled by BAS.

“Off” if unit is switched off

13. Occupancy override

1. Control

Figure 4

Four main buttons on THS04 are available (cf Figure.3)

1 - Mode button: Simple push to switch the unit mode (AUTO/COOL/HEAT) when unit is OFF

2 - Fan button: Simple push to switch the fan mode (AUTO/ON) when unit is OFF

3 - Power button: 3 seconds push to stop/start the unit

4 - Clock button: Simple push to switch occupancy (fresh air management) (Occupied/Unoccupied) when

unit is ON. In case of scheduler enabled, the simple push switch the unit fresh air occupancy mode

temporary during override timer.

5 - Push&Rotate button: menu navigation and temperature setpoint change. In case of scheduler enabled,

the setpoint change switch the unit Heating / Cooling zone temperatrure setpoint during override timer.

2. Menu Navigation

Navigation through menus is done by the “push & rotate” button (button 5 on Figure 3).

The way to use that button is: rotate to modify a setpoint or a value, then wait 3s for that setpoint or value to

be automatically registered. The symbol “Set” disappears.

Figure 5

3. Protect setpoints and mode modification by password

The THS04 factory default level is set in PGD1 setting : THS04 – Acces Level = Disable

It means a that there is no need of password to change unit and fan mode or edit setpoint and occupancy

state.

However, it is possible to enable the password by changing setting in PGD1 : Setting-THS04 : Access

Level Enable.

When activated, the password has to be entered on the THS04 under Menu 2 (See Figure 5).

Password Disable by default

3 - Set = Setpoint1 + Wait

+ Wait

Tc : Cooling

setpoint change

Edit + Wait

Th : Heating

setpoint change

Edit

2 - Pass = Password + Wait

2 - Read = Setpoint

display

+ Wait

Tc : Cooling

setpoint change

Th : Heating

setpoint change

0 - Menu = Enter

Home

Screen

+ Wait

1 : First password

digit

Edit + Wait

2 : second

password digit

Edit

4. Local Unit shutdown, Local fan and operation mode change

The THS04 is able to switched OFFON unit by pressing during 3seconds the ON/Off button (button 3

Figure4)

Fan mode can be switched AUTO ON by pressing during 3seconds the Fan button (button 2 Figure4).

Unit mode can be switched AUTO COOL HEAT by pressing during 3seconds the Mode button (button

1 Figure4)

Important: Fan mode or Unit mode switch can only be performed after switching the unit in OFF (pressing

during 3seconds the ON/Off button)

Figure 6

5. Occupancy mode change

When Time/Day scheduler is activated under PGD1, it is possible to temporary override scheduler

occupancy mode with THS04.

THS04 Occupancy override will switch unit to occupied state if scheduler active time band has set it in

unoccupied and vice-versa.

When Time/Day scheduler is not activated, the THS04 Occupancy override will switch temporary unit from

unoccupied to occupied.

To override minimum fresh air occupancy mode, a simple push on button 4 (Figure. 4) will move the state

of the unit from unoccupied to occupied. THS04 displays active occupied / unoccupied minimum fresh air

state with the logo of figure 7

Figure 7

Occupied mode override will remain active until override timer expires. It is possible to edit the override

timer under PGD1: Setting-THS04 : Occupancy Override timer 60 minutes (default value).

If Occupancy Override timer value is set at zero. It will disable the timer function and let unit fresh air

occupancy state unchanged if no other actions are performed on button 4.

6. Active temperature setpoint override command

It is possible with THS04 to override the active temperature setpoint by an offset of +/- 2°C. Turning the

button 5 (Figure.4) will offset the active setpoint (Cooling or Heating depending of current mode of unit).

Push

Unit

ONOFF

Push

Fan

AUTOON

Push

Unit mode

AUTOCOOLHEAT

Unit OFF Unit OFF

Push

Unit fresh air occupancy

Figure 8

The temperature setpoint override command will remain active until Occupancy override timer expires. It is

possible to edit the override timer under PGD1: Setting-THS04: Occupancy Override timer 60 minutes

(default value). If Occupancy Override timer value is set at zero, it will disable the timer function and let

modified setpoint unchanged if no other actions are performed on button 5 (Figure 4).

Note : The amount of offset applied to the active setpoint is also applied to the opposite mode setpoint. For

instance, an offset of +1.5K on Heating setpoint (Active Heating setpoint 20°C21.5°C) will move the

cooling setpoint with the same magnitude (Active Cooling setpoint 24°C25.5°C)

7. Real time clock adjustment

It is possible to adjust the controller time and date under PGD1: Setting- Clock and password: Time and

Date settings.

Version History

•Oct-2017: Simplify default level and remove password to change mode, occupancy and setpoint .

Implementation started with CH536 release 1.52.

Trane optimizes the performance of homes and buildings around the world. A business of Ingersoll Rand, the leader in creating

and sustaining safe, comfortable and energy efficient environments, Trane offers a broad portfolio of advanced controls and HVAC

systems, comprehensive building services, and parts.

For more information, visit www.Trane.com.

Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.

RT-SVU010B-GB_1217

supersedes RLC-SVU010A_1116

Active setpoint

display

Active setpoint

temporary override

+ Wait

Home

Screen

Table des matières

Autres manuels Trane Thermostat

Trane

Trane BAYSTAT150A Manuel

Trane

Trane RT-SVU010A-GB Manuel utilisateur

Trane

Trane THT02775 Manuel utilisateur

Trane

Trane Z WAVE TZEMT400AB32MAA Manuel utilisateur

Trane

Trane XR203 Manuel utilisateur

Trane

Trane XL824 Manuel utilisateur

Trane

Trane TZONE940AC52Z Guide de dépannage

Trane

Trane TZON1050AC52ZAA Manuel utilisateur

Trane

Trane Thermostats Mode d'emploi

Trane

Trane XR401 Comfort Control Manuel utilisateur

Trane

Trane TZEMT400BB32MMA Manuel utilisateur

Trane

Trane XR202 Manuel utilisateur

Trane

Trane TAYSTAT 540 Manuel utilisateur

Trane

Trane TZONE950AC52ZA Manuel utilisateur

Trane

Trane TAYSTAT 575 Manuel utilisateur

Trane

Trane XT302C Instructions de montage

Trane

Trane TCONT200AN11AA Instructions de montage

Trane

Trane XR102 Manuel utilisateur

Trane

Trane Schlage LiNK TZEMT400BB32MAA Instructions de montage

Trane

Trane XL824 Manuel utilisateur

Trane

Trane 3518-7065 Manuel utilisateur

Trane

Trane TCONT600AF11MA Manuel utilisateur

Trane

Trane ProSpace THT03191 Manuel utilisateur

Trane

Trane X13511537-01 Manuel

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur