Trane VariTrac Manuel utilisateur

VariTrac Installation

Workshop 3

VariTrac Installation

Goal: You will install a VariTrac CCP , zone controllers, and communicating sensor/bypass

damper control in this workshop. You will also install 24Vac power, the Comm4 communications

link and zone sensor wiring. Sections of this workshop include the following:

Install VariTrac UCMs and digital zone sensor

Install Communicating Bypass Damper assembly

Install VariTrac Central Control Panel

Startup VariTrac and setup system from operator display

Reference: VariTrac Central Control Panel Installation Manual (VAV-SVN03A-EN)

VariTrac Central Control Panel Operators Guide (VAV-SVP01A-EN)

Job Description:

A VariTrac III and Tracker 10 will be installed at B&R Specialty Metals. The VariTrac CCP is

applied to the office area HVAC system. This HVAC system consists of Voyager CV unit

supplying 3 separately controlled zones. VariTrac is applied as a changeover bypass system and

uses a bypass damper assembly to monitor and control supply air static pressure and

temperature. VariTrac devices required for this job include the following:

VariTrac CCP

VariTrac UCMs (3)

Zone sensors (3)

Communicating Bypass Damper assembly

Tracker is used to control the warehouse area and brazing workshop. Tracker controls scheduling

of the warehouse rooftop unit, exhaust fans for the restroom and brazing workshop, outdoor

lighting, and occupancy for the Varitrac system.

03- VariTrac Installation Workshop.doc 3-1

VariTrac Installation

The drawing shows the VariTrac system you will install in this workshop. you will

complete the power wiring and communications link. Then startup the system.

Install VariTrac UCMs and digital zone sensor

Reference: VariTrac Installation Manual (VAV-SVN03A-EN), Pages 23 through 27

1. Set the address DIP switches on each of the UCM boards to addresses 1, 2, and 3.

2. Connect UCM Comm4 wiring to terminalsTB2-1 and TB2-2, TB2-3 and TB-2-4 on each UCM

using the pre-configured wiring harness provided.

Important! Polarity must be observed at comm link connections on all devices that share the

Comm4 link.

3. Connect 24Vac power to terminals TB1-1 (24V) and TB-2 (ground) on each UCM using the

pre-configured wiring harness provided.

03- VariTrac Installation Workshop.doc 3-2

VariTrac Installation

Caution: It is not recommended that 24Vac power be shared between controllers.

However, if controllers share a common transformer, polarity must be observed on 24Vac

connections on UCMs that share the same transformer.

Question: Would a VariTrac UCM set to address 25 communicate to a VariTrac? _____.

Why or why not? _______________________________________________________.

Question: Will the comm link function even though the electrician swapped polarity at

one of the Comm4 devices? ______. Why or why not? ________________________.

4. Install a zone sensor to VariTrac damper UCM, address #1. Use wire provided for both the

sensor/adjustable setpoint.

5. Install a digital zone sensor to VariTrac damper UCM, address #2. Use wire provided for both

the sensor/adjustable setpoint and 24Vac power.

Reference: VariTrac Installation Manual (VAV-SVN03A-EN), Pages 28 through 31

03- VariTrac Installation Workshop.doc 3-3

VariTrac Installation

Question: Can both 24Vac power and sensor wiring share the same conduit? ____.

Why or why not? _____________________________________________________

Install Communicating Bypass Damper Assembly

Reference: VariTrac Installation Manual (VAV-SVN03A-EN), Pages 21 through 22

Note:

The communicating sensor/bypass assembly is normally located between the

supply fan and the bypass damper in the least turbulent location possible. It is

recommended that the d stance between the con roller assembly and the nearest

upstream transition be at least 2 to 3 equivalent duct diameters.

i t

6. Locate the communicating sensor/bypass assembly housing near the VariTac lab equipment

and remove metal cover.

7. Verify address DIP switches on the communicating sensor/bypass UCM board are set to

address ‘ 33 ’.

Note: The communicating sensor assembly UCM address DIP switches are set at the

factory to Address 33.

8. Connect the communications link wiring to terminalsTB2-1 and TB2-2, TB2-3 and TB-2-4

using the pre-configured wiring harness provided. Observe (+) and (-) polarity on the link.

Note: A pre-configured wiring harness is provided to connect both 24Vac and the

communications link to the communicating bypass/damper UCM.

9. Connect 24Vac power to terminals TB1-1 (24V) and TB-2 (ground) on the UCM

Caution: It is not recommended that 24Vac power be shared between controllers.

However, if controllers share a common transformer, polarity must be observed on 24Vac

connections on UCMs that share the same transformer.

03- VariTrac Installation Workshop.doc 3-4

VariTrac Installation

Question: How large a hole is required in the supply duct to insert the supply temperature

and static pressure sensor? ______________________.

Question: What is the maximum distance between the bypass damper actuator and

communicating sensor/ bypass assembly if using the cable shipped with the bypass damper

actuator unit? ______________.

Install VariTrac Central Control Panel

Reference: VariTrac Installation Manual (VAV-SVN03A-EN), page 17

10. Remove the Display and Main modules from the termination module to gain access to the

termination board wiring.

03- VariTrac Installation Workshop.doc 3-5

VariTrac Installation

Termination module

Main module

Display module

11. Connect 24Vac transformer leads to AC power terminations (TB1-1,TB-2) on the VariTrac

termination board.

Note: A dedicated 24 Vac, 30VA Class 2 transformer is required to power the VariTrac

Central Control Panel. The ground wire (TB2-3) is connected to the circuit breaker panel.

12. Connect communications link to TB2-10 (+) and TB2-11(-) from the zone damper UCMs and

the communicating sensor/bypass UCM.

03- VariTrac Installation Workshop.doc 3-6

VariTrac Installation

13. Verify that 24 Vac power, and Comm4 link are correctly terminated at the VariTrac

termination board.

14. Install Main logic board onto the VariTrac termination board module.

15. Install the VariTrac operator display module onto the main module.

03- VariTrac Installation Workshop.doc 3-7

VariTrac Installation

Startup VariTrac and setup system from operator display

Reference: VariTrac Installation Manual (VAV-SVN03A-EN), page 43 to 51

16. Apply 24Vac power to VariTrac and UCMs.

Question: What is the minimum configuration of VariTrac devices required for the CCP

startup sequence to begin? ____________________________________________.

17. View the VariTrac operator display. The ‘System Initialization in Progress’ screen displays.

Please Wait

System initialization is in progress

Initialization status: 90% complete

Patience required: VariTrac operator goes through an initialization routine which could

last several minutes. Once initialization is complete when the operator displays the

normal ‘Home Screen’.

18. The VariTrac home screen should display as shown in the screen capture

Note: ‘Calibration mode is active’ occurs after an initial start-up sequence. In calibration,

the CCP automatically prepares the VariTrac system for operation by disabling heating

and cooling, closing the bypass damper, opening all zone dampers to their maximum

position and starting the fan. Calibration re-indexes the zones and bypass damper and

recalibrates the static pressure setpoint.

Reference: VariTrac Installation Manual (VAV-SVN03A-EN), page 44 for an explanation

of the VariTrac calibration sequence.

Question: Name 3 fault conditons that cause the home screen display to display: ……

******Priority Shutdown Active******

a. _________________________

b. _________________________

c. _________________________

03- VariTrac Installation Workshop.doc 3-8

VariTrac Installation

19. Press the View Button on the Home Screen. Three devices should display as shown.

20. Press the Home button to return to the home screen.

21. Make the following Setup changes to VariTrac:

Hint: Press the ‘Advanced’ button to access the following options.

πSet current date and time

πChange System Name: from “VariTrac CCP” to “Front Office Area”

πSelect HVAC Unit Type: as ‘Voyager Commercial CV’

πChange Discharge Heating Setpoint: to ‘100.0’

22. Press ‘Advanced’, then ‘System setup and Status’, finally ‘System Status’.

23. Record the following and be prepared to explain the recorded values:

πHVAC Unit Comm: ___________________.

πHVAC Comm Status: __________________.

πOperating Mode: ____________________.

πSupply Air Temperature: ___________________.

πExternal Time Clock Input: ________________.

24. Press the Home button to return to the home screen.

25. Press the View Button on the Home Screen.

26. Select each zone and rename as follows:

π“Zone 1” rename to: = “Administration Area”

π“Zone 2” rename to: = “Lobby Area”

π“Zone 3” rename to: = “Sales Area”.

03- VariTrac Installation Workshop.doc 3-9

VariTrac Installation

You have completed this workshop!

03- VariTrac Installation Workshop.doc 3-10

Table des matières

Autres manuels Trane Régulateurs de température

Trane

Trane PolyTherm ARTC-SVX005A-EN Instructions d'installation et d'utilisation

Trane

Trane TCONT800AS11AA Manuel utilisateur

Trane

Trane ZUSTATALP510 Instructions de montage

Trane

Trane WFS 1 Guide de démarrage rapide

Trane

Trane TZEMT524AA21MA Instructions de montage

Trane

Trane ZSENS930AW00MA Instructions de montage

Trane

Trane ZUSTATALS510 Manuel utilisateur

Trane

Trane ComfortLink II XL 850 Manuel utilisateur

Trane

Trane X1379088401 Instructions d'installation et d'utilisation

Trane

Trane TCONT401AN21MA Comfort Control Manuel utilisateur

Trane

Trane TCONT402AN32DA Manuel utilisateur

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage