Trane Tracer AH541 Instructions de montage
© 2008 Trane. All rights reserved
June 2008 3270 3403 D
Installation Sheet
Frame-mounted Tracer™ AH541 Controller
Order Numbers: BMTA000CAB00
The frame-mounted Tracer AH541 controllers can be used to replace controllers in existing equipment or mounted in new
equipment or custom enclosures.
NOTICE
Avoid Equipment Damage!
Install and use the controllers as specified by the manufacturer. Failure to do so may result in equipment damage.
Warnings, Cautions, and Notices
Warnings, cautions, and notices are provided in appropriate places throughout this document:
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe practices.
NOTICE:Indicates a situation that may result in equipment or property-damage only accidents.
3270 3403 D 2
Frame-mounted Tracer™ AH541 Controller
Operating Environment Requirements
Make sure that the operating environment conforms to the specifications listed in Ta b l e 1 .
Enclosure Requirements
Before installing the frame-mounted controller, ensure that the enclosure or mounting space meets the following
minimum requirements:
• Minimum clearance (shown in the illustration below)
• 24 Vac dedicated power supply
• Compliance with National Electrical Code™ (NEC) and applicable local electrical codes for high-voltage power wiring
to the enclosure
Figure 1. Minimum clearances
Table 1. Specifications
Temperature: From -40°F to 158°F (-40°C to 70°C)
Humidity: 5–95% non-condensing
Power requirements: 21–27 Vac (24 Vac nominal)
Altitude: 6500 ft (2000 m)
Installation: Category 3
Pollution: Degree 2
BO5
BO4
BO3
BO2
BO1
BO6
24VAC
AO4
AO3
AO6
AO5
AO2
IN3
IN2
IN1
AO1
IN6
IN7
IN5
IN11
IN12
IN10
IN9
IN8
IN4
1/2 in. (13 mm)
1/2 in. (13 mm)
6 in. (152 mm)
(For I/O wires)
1/2 in. (13 mm)
33270 3403 D
Frame-mounted Tracer™ AH541 Controller
Installing the Termination Board
To install the termination board:
1. Remove the controller from its packaging and separate the top and bottom frames.
2. Using the bottom frame (with the termination board) as a template, mark the location of the four mounting holes and
the grounding screw on the mounting surface.
3. Set aside the controller and then drill holes for #8 (4 mm) screws at the marked locations.
4. Drill a 1/8 inch diameter pilot hole for the supplied grounding screw.
5. Secure the controller to the mounting surface with the enclosed using #8 (4 mm) screws (not supplied) in the mounting
holes.
Figure 2. Dimensions and mounting holes
Mounting hole
(4x)
Grounding screws
location
3270 3403 D 4
Frame-mounted Tracer™ AH541 Controller
Installing the Main Circuit Board
The controller does not ship with the top plastic frame installed. The board can be kept in the office and programmed while
the enclosure is mounted and wired. After programming has been completed, connect the circuit board to the termination
board.
To begin, verify that the 24 Vac power cable is not connected to the termination board and then install the main circuit
board as shown in Figure 3, p. 5:
53270 3403 D
Frame-mounted Tracer™ AH541 Controller
Figure 3. Installing the main circuit boards
G
BO5
BO4
BO3
BO2
BO1
BO6
24VAC
AO4
AO3
AO6
AO5
AO2
IN3
IN2
IN1
AO1
IN6
IN7
IN5
IN11
IN12
IN10
IN9
IN8
IN4
BO1 BO3 BO5
BO2 BO4 BO6
SERVICE COMM
FAN EX FAN TEST STATUS
BO5
BO4
BO3
BO2
BO1
BO6
24VAC
AO4
AO3
AO6
AO5
AO2
IN3
IN2
IN1
AO1
IN6
IN7
IN5
IN11
IN12
IN10
IN9
IN8
IN4
BO1 BO3 BO5
BO2 BO4 BO6
SERVICE COMM
FAN EX FAN TEST STATUS
H
I
1. Hold the top frame (A) at a 90° angle to the bottom frame (B).
2. Connect the 60-pin cable (C) to the 60-pin cable ejector slot (D) by pressing down firmly on the cable until the ejector
tabs collapse and snap over the ends of the cable. Then, connect the 20-pin cable (E) to the 20-pin slot (F).
3. Align the snaps on the top frame (G) with the mounting locks on the bottom frame and then push the two frames
together in the direction indicated by the arrows.
Note: You will hear a click when the frames connect. For controllers with an operator display, connect the operator-
display cable to the circuit board.
4. Install the supplied grounding screw (6-32 x 2 inch, thread-rolling screws) into the assembly and turn it into the
sheet metal backing.
Grounding
screw
Important: The 60-pin cable ejector is designed to eject the 60-pin cable when disconnecting (refer to the lower right inset above).
B
A
C
D
E
F
Ensure that the slot keys are
aligned when connecting the
60-pin cable to the 60-pin
cable ejector.
Grounding screw
5. Locate the 24 Vac power
connector on the termination
board. Remove the mating plug
with screw terminals.
6. Attach the 24 Vac power-supply
cable to the screw terminals on
the mating plug.
7. Connect the 24 Vac power cable to
the termination board (H). The
green status LED will light (I).
www.trane.com
For more information, contact your local Trane
Literature Order Number 3270 3403 D
Date June 2008
Supersedes 3270 3403 C
Trane has a policy of continuous product and product data improvement and reserves the right to
change design and specifications without notice.
Tracer, Trane, and the Trane logo are trademarks of Trane in the United States and other countries. All
trademarks referenced in this document are the trademarks of their respective owners.
Tracer AH541 Declaration of CE Conformity
The manufacturer hereby declares that the product:
Conforms to the following standards or other normative documents:
This document validates CE conformity of the Tracer AH541 modular configurable controller.
Manufacturer name: Trane
Manufacturer address: 4833 White Bear Parkway
St. Paul MN 55110, USA
Product name: Tracer AH541modular configurable controller
Model numbers: BMTA000BAB00, BMTA000BAB01, BMTA000CAB00
Electromagnetic emission:
(by Council directive 89/336/EEC)
EN61000-6-4:2001
Radiated EN61000-3-2:
Conducted EN61000-3-3:
Amendment A14:2000
1995 Class B limit
1995 Class B limit
Electromagnetic immunity:
(by Council directive 89/336/EEC)
EN61000-6-2:1999
IEC 1000-4-2:1995
EN61000-4-2
±6.0 kV by contact
±8.0 kV by air
IEC 1000-4-3:1995
EN61000-4-3:1996
Amendment A1:1998
10.0 V/m
80 to 1000 MHz
IEC 1000-4-4:1995
EN61000-4-4
±2.0 kV ac power lines
±1.0 kV signal lines
IEC 1000-4-5:1995
EN61000-4-5
±2.0 kV
IEC 1000-4-6:1996
EN61000-4-6
10.0 V
0.15 to 80 MHz
IEC 1000-4-8:1993
EN61000-4-8
IEC 1000-4-11:1994
EN61000-4-11
When and Where Issued
Electromagnetic Emission: 05/18/2001
Electromagnetic Immunity: 05/18/2001
Mark of Compliance:
John Olson
Design/Compliance Engineer
European contact
Societe Trane (Epinal, France)
1, rue des Ameriques, B.P. 6
F-88191 Golbey Cedex, France
Phone: (33) 329.31.73.00
Fax: (33) 329.81.24.98
Autres manuels pour Tracer AH541
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Trane Contrôleurs
Trane
Trane Tracer UC400 Manuel utilisateur
Trane
Trane Tracer Manuel utilisateur
Trane
Trane Tracer VV550 Instructions d'installation et d'utilisation
Trane
Trane Tracer ZN510 Manuel du propriétaire
Trane
Trane Tracer UC600 Instructions d'installation et d'utilisation
Trane
Trane TRACER CH532 Manuel utilisateur
Trane
Trane Tracer TD7 Manuel utilisateur
Trane
Trane 700 Manuel utilisateur
Trane
Trane Tracer AH540 Instruction manuelle
Trane
Trane Symbio 800 Manuel utilisateur
Trane
Trane Tracer ZN524 Guide de configuration
Trane
Trane mP30 Manuel du propriétaire
Trane
Trane VariTrane VAV-SVX02B-EN Manuel du propriétaire
Trane
Trane ReliaTel Manuel utilisateur
Trane
Trane Tracer ZN521 Manuel du propriétaire
Trane
Trane Oxbox JAYLOAM002 Manuel utilisateur
Trane
Trane Tracer SC Manuel utilisateur
Trane
Trane Tracer CH535 Manuel utilisateur
Trane
Trane Tracer VV550 Manuel utilisateur
Trane
Trane SmartGen HSC940 Manuel utilisateur
