Traditional Tool Repair MUL-370 Manuel utilisateur

No KEY No PARTDESCRIPTIONQTY.

1ELDNAH10-0731

1LWAPNOISNET20-0732

2NIP30-0733

1LEEHWTEHCTAR40-0734

1RELLOR50-0735

1NIPRELLOR60-0736

1REVEL70-0737

1GNOLLWAP80-0738

1TROHSLWAP90-0739

1REVELRETTUC01-07301

1GNIRPSREVEL11-07311

1EMARF21-07321

1DAPREPPIRG31-07331

1GNISUOHRETTUC41-07341

1RETTUC51-07351

1SSALDNIW61-07361

1GNIRPS71-07371

1TFAHSTOOFREPPIRG81-07381

1RELLORTOOFREPPIRG91-07391

1TFAHSCIRTNECCE02-07302

1REDLOHREPPIRG12-07312

1GNIRPSTOOFREPPIRG22-07322

1)"4/3(GNIRGNINIATERE32-07332

24 370-24WASHER 5х11х17.0

1TOOFREPPIRG52-07352

1REHSAW62-07362

1REVELYRAILIXUA72-07372

1GNIRPSYRAILIXUA82-07382

3GNIRPSLWAP92-07392

1BONK03-07303

1"61/5GNIRPILK13-07313

18x2,1NIPRETTOC23-07323

33 370-33 SET SCREW М6х12 DOG POINT 3

18,11x4RELLORELDEEN43-07343

1"8/5GNIRPILK53-07353

2"61/5x"8/1NIPGNIRPS63-07363

1GNIRAEBENALP73-07373

38 370-38SET SCREW М5х8 HALF DOG POINT 1

39 370-39 COUNTERSUNK HEAD SCREW M5x8 2

40 370-40 SET SCREW М5х16

18REHSAW14-07314

1LLAMSGNIRAEBENALP64-07364

4025

MUL-370

for PET Strapping

Heavy Duty Tensioner

WWW.TRADITIONALTOOL.COM

For Parts & Service 1-877-862-6699

Fig. 1 –Starting Position

1. Raise Gripper Foot 25 by pressing down on Tension Handle 01. Load bottom strap 101 under Cutter

Housing 14, under Gripper Foot 25 and leave at least 2” of the strap extended out from the front of the

tool for seal placement as shown on Fig. 2.

Fig. 2

2. Load upper strap 100through Cutter Housing 14, through Windlass 16 as shown on Fig. 3.

Fig. 3

WWW.TRADITIONALTOOL.COM

For Parts & Service 1-877-862-6699

3. Apply tension by ratcheting Tension Handle 01 as shown on Fig. 4.

Fig. 4

4. Once satisfactory tension is achieved the strap is ready to be sealed. With the Seal 103 securely in

place use the appropriate Sealer 104 to snap the Seal 103. Place the Jaws 105 of the sealer on the

middle of the Seal 103 and press the Handles 106 until they cannot be squeezed any further. Then

unclenched the Handles 106 and remove the Sealer 104 as shown on Fig. 5

Fig. 5

WWW.TRADITIONALTOOL.COM

For Parts & Service 1-877-862-6699

5. Once the joint is secure the strap is ready to be cut. Push down on the Tension Handle 01 until the

strap is cut and slide the tensioner to the right to release the strap from under the Gripper Foot 25 as

shown on Fig. 6. The operation cycle is now complete.

Fig. 6

WWW.TRADITIONALTOOL.COM

For Parts & Service 1-877-862-6699

Table des matières

Autres manuels Traditional Tool Repair Outils

Traditional Tool Repair

Traditional Tool Repair JK1219 Manuel de service

Traditional Tool Repair

Traditional Tool Repair DTF-56 Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair STTR Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair A338.0002 Mode d’emploi

Traditional Tool Repair

Traditional Tool Repair DTF-76 Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair DSA-116 Mode d’emploi

Traditional Tool Repair

Traditional Tool Repair DTP-100UL Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair DTF-125 Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser