Traditional Tool Repair A338.0002 Mode d’emploi

13294601.en/MAS/© 01.03

OPERATION MANUAL / SPARE PARTS LIST

MANUAL SEALLESS

STEEL STRAPPING TOOL WITH

ADJUSTABLE TENSION LEVER

MODEL A338.0002

13.2946.01

Sales and Service 877-862-6699

1 SAFETY INSTRUCTIONS

Read these instructions carefully. Failure to follow these instructions can result in severe personal injury.

Eye injury hazard

Failure to wear safety glasses with side shields can result in severe eye injury or blindness. Always wear safety glasses with side shields

which conform to ANSI Standard Z87.1.

Operation

Tool must not be used by persons not properly trained in their use. Before tensioning strap, read and understand the tool operating

instructions. Failure to follow the operating instructions or improper load positioning could result in strap breakage.

Become familiar with your tool and keep fingers away from areas that can pinch or cut.

Joints

You are fully responsible to review the joints made by your tool. Become familiar with the seal control and seal adjustment described in

this operation manual. Misformed joints may not secure the load and could cause serious injury. Never handle or ship any load with

improperly formed joints.

INDEX PAGE

1 SAFETY INSTRUCTIONS 2

2 WARRANTY CONDITIONS AND LIABILITY 4

3 APPROPRIATE USE 4

4 TECNICAL DATA 4

5 CHART OF TYPES A338.0002 5

6 OPERATION LEVERS 6

7 OPERATION 6

8 SPARE PARTS LIST 13.2946.01 10

9 SEAL CONTROL 13

10 SEAL ADJUSTMENT 14

11 TENSION FORCE ADJUSTMENT 14

12 CLEANING 15

13 EXCHANGE OF WEARING PARTS 15

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

Dispensing strap

Only dispense strap from a dispenser specifically designed for strap.

Tuck strap end back into dispenser when not in use.

Protective gloves

When handling strap, always wear protective gloves.

Strap warnings

Never use strap as a means of pulling or lifting loads. Failure to follow these warnings can result in severe personal injury.

Strap breakage hazard

Improper operation of the tool, excessive tensioning, using strap not recommended for this tool or sharp corners on the load can result in

a sudden loss of strap tension or in strap breakage during tensioning, which could result in the following:

• A sudden loss of balance causing you to fall.

• Both tool and strap flying violently towards your face.

Note as follows:

• If the load corners are sharp, use edge protectors.

• Place the strap correctly around a properly positioned load.

• Positioning yourself in-line with the strap, during tensioning and sealing, can result in severe personal injury from flying strap or

tool. When tensioning or sealing, position yourself to one side of the strap and keep all bystanders away.

• Use the correct strap quality, strap width, strap gauge and strap tensile strength recommended in this manual for your tool. Using

strap not recommended for this tool can result in strap breakage during tensioning.

Cutting tensioned strap

When cutting strapping, use the proper strapping cutter and keep other personnel and yourself at a safe distance from the strap. Always

stand to side of the strap, away from the direction the loosened strap end will fly. Use only cutters designed for strap and never hammers,

pliers, hacksaws, axes, etc.

Fall hazard

Keep your working area tidy. Untidiness of your working area may cause a risk of injury. Maintaining improper footing and/or balance

when operating the tool can cause you to fall. Before tensioning and especially in elevated areas, always establish good balance. Both

feet should be securely placed on a flat, solid surface, especially when working in elevated areas. Do not use the tool when you are in an

awkward position.

Pay attention to the rules and regulations for preventions of accident which are valid for the work place.

Tool hazards

A well maintained tool is a safe tool!

Check tool regularly for broken or worn parts. Do not operate a tool with broken or worn parts.

Never modify any tool. Modification can result in severe bodily injury.

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

4A3380002.en_teil1

2 WARRANTY CONDITIONS AND LIABILITY

FROMM Holding AG warrants all its strapping tools and machine heads during a period of 90 days from the

date of sale. The warranty includes all deficiencies clearly resulting from poor manufacturing or faulty materials.

Damage claims as a result of production shutdowns and claims for damage to persons and to property resulting

from warranty deficiencies cannot be asserted by the customer.

The warranty excludes:

• wearing parts

• deficiencies resulting from improper installing, incorrect handling and maintaining the tool

• deficiencies resulting from using the tool without or with defective security- and safety devices

• disregard of directions in the operation manual

• arbitrary modifications of the tool

• deficient control of wearing parts

• deficient repair works of the tool

• Use of consumable products not recommended by FROMM Holding AG

We reserve the right to modify the product at any time in order to improve its quality.

3 APPROPRIATE USE

The tool model A338 has been designed to strap packages with steel strapping exclusively.

The warranty / liability excludes:

• non appropriate use of the tool,

• disregard of directions in the operation manual,

• disregard of control- and maintenance instructions.

4 TECNICAL DATA

Dimensions without suspension bracket

Tensioning force

5.5 KN / 1240 lbs with adjustment at 80 Nm / 710 lbs (240 N / 54 lbs manual force).

Sealing force

The manual force required for sealing is approx. 220 N / 50 lbs.

Joint strength

Approx. 80% of the strap’s tensile strength.

Tool Package

Length: 670 mm / 26.4"

(Lever in horizontal position) 690 mm / 27.2"

Width: 170 mm / 6.7" 215 mm / 8.5"

Height: 450 mm / 17.7"

(Sealing lever in vertical position) 160 mm / 6.3"

Weight: 5.9 kg / 13 lbs 0.77 kg / 1.7 lbs

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

5A3380002.en_teil1

Steel strapping

5 CHART OF TYPES A338.0002

Uniflex = Strapping with max. tensile strength of 850 N/mm2(123 000 psi)

Ultraflex = Strapping with max. tensile strength of 1100 N/mm2(160 000 psi)

Suspension bracket

For vertical and horizontal operation the tool can be suspended on a spring loaded balancer using suspension

bracket A33.5301.

Width: 12.7 - 19 mm / 1/2"-3/4" (see chart of types)

Thickness: 0.50 - 0.70 mm / .020"-.028" (see chart of types)

Quality: Fundamentally the A338 allows the use of all current steel straps with tensile strengths ranging

from 700 to 1100 N/mm2/ 100 000 - 160 000 psi (see chart of types).

Straps with a low breaking elongation are unsuitable.

Item No. Model Strap width Strap thickness

Uniflex Ultraflex

13.2911 A338/12.7/0.50-0.64/TW 12.7mm / 1/2" 0.50-0.64mm / .020-.025" 0.50-0.64mm / .020-.025"

13.2916 A338/12.7/0.70/UNI/TW 12.7mm / 1/2" 0.70mm / .028" -

13.2921 A338/13/0.50-0.64/TW 13.0mm 0.50-0.64mm / .020-.025" 0.50-0.64mm / .020-.025"

13.2926 A338/13/0.70/UNI/TW 13.0mm 0.70mm / .028" -

13.2931 A338/16/0.50-0.64/TW 16.0 / 5/8" 0.50-0.64mm / .020-.025" 0.50-0.64mm / .020-.025"

13.2936 A338/16/0.70/UNI/TW 16.0 / 5/8" 0.70mm / .028" -

13.2941 A338/19/0.50-0.64/TW 19.0mm / 3/4" 0.50-0.64mm / .020-.025" 0.50-0.64mm / .020-.025"

13.2946 A338/19/0.70/UNI/TW 19.0mm / 3/4" 0.70mm / .028" -

A33.5301

Vertical A33.5301

Horizontal

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

6A3380002.en_teil1

6 OPERATION LEVERS

7 OPERATION

Feeding the strapping around the

package

The strapping is fed around the package in the

direction as shown in the illustration. The strapping

end is held tightly with the left hand and pulled firmly

towards the operator with the right hand.

Loading the strapping

The rocker is raised with the right hand. The left hand

inserts the two straps lying precisely upon another

into the tool until they hit the strap stops.

The lower strap end must slightly protrude the end of

the base plate.

Be certain that the strapping is held by the strap guide.

Tensioning handle

Sealing lever

Rocker

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

7A3380002.en_teil1

Tensioning the strapping

The tool is held tightly with the left hand being placed on the

sealing lever. The torque tension lever is now moved forward

and backward with the right hand until the torque disengages

(click-stop sound ).

Sealing the strapping

The sealing lever is moved forward using the left hand until it

hits the stop. The lever is then moved back to its initial position.

When sealing, the right hand absorbs the sealing force by

holding the tensioning handle.

Releasing the tool

Hold the cut off strap end with the left hand, lift the rocker with

the right hand and push the tool from the applied strap to the

right.

Releasing the feed wheel after faulty operation

If the feed-wheel is jammed with the strap and the rocker cannot

be released the following procedure is necessary to remove the

strapping from the tool:

• loosen screws N1.1563, N1.1564 and N11.1112.

• lift rocker and remove steel strapping from the tool.

• retighten screws N1.1563, N1.1564 and N11.1112 with a

torque of 90 Nm / 800 lbs. Rocker

N1.1564

N1.1563

N11.1112

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

2 31A

A33.0103

A33.0105

A33.0104

N1.1912

N1.6503

N4.9145

N2.4902

N2.4906

A33.5127

A33.5126

A33.5105

N1.6203

N2.2147

N1.1806



N2.2110

A38.3134

A38.3123

A33.5118

A33.5125

N2.2109

A38.3130

N1.1807

A33.5110



N3.3160



N3.3160

N1.1564





N3.3159

N3.3160



A38.3124

A33.5119



A33.5124



A33.5123

A33.5109

A33.5117

A33.5122

A33.5121



A33.5120

A33.5101

A33.5129

A33.5133

N1.3513

N3.2341

N2.2125

A38.3239

A38.3129



N1.1304

N1.1807



N11.1112



N2.5215



N1.1563



N41.9128

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

4567

A33.0106

A33.3170



N2.2178

A33.5128

A33.0110

A33.0108

A33.0107

A33.0109

N1.3503

N4.1116

N2.5606



N2.1108

A33.5223

A33.3171

N2.1606

A33.5206

N4.5116

A33.3175

A33.3174

A33.3173

N2.5213

A33.5204



N3.2341

A33.5203

A33.5201

A38.3210

N3.2610

A33.5225

A33.5216

A33.5221

A33.5220



N3.3116

N7.1205

N1.6220

N2.2172

N1.1106

N6.6261

A33.5212

N3.4307

N3.4311

N2.1608

N1.6207

N1.1113 N1.1113

N1.1136

N3.2343 N3.2314

A33.5205

N2.1607



A33.3169



N2.2178

N3.1707



N3.1702



A33.3172



N3.1702



A33.5209



A33.3110



N2.5154

N4.5119



A33.5211



A33.5210



13294601.z



ESSO Beacon 2



Molykote BR 2 plus



Loctite 222



90 Nm



Loctite 603



Orientation

N3.4507





N3.2405



N3.2405

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

* = Wearing parts [ ] = Group ->[ ] = in group

10 13294601.een

8 SPARE PARTS LIST 13.2946.01

13.2946.01 A338/19.0/0.70/UNI/TW A338.0002.01 04/06/98

Item-No. Pcs. Description Dimension Field

[A33.0103] 1 SEALING HOUSING B3

[A33.0104] 1 DIE AND CUTTER SUPPORT C2

[A33.0105] 1 BEARING PICK-UP ATTACHMENT C1

[A33.0106] 1 SEALING HANDLE A5

[A33.0107] 1 ROCKER E7

[A33.0108] 1 GEAR C7

[A33.0109] 1 END COVER E5

[A33.0110] 1 TORQUE LEVER A7

A33.3110 2 TENSIONING PAWL B5

A33.3169 ->[A33.0110] 1 HINGE B6

A33.3170 ->[A33.0110] 1 COUPLER A7

A33.3171 ->[A33.0110] 1 TUBE B7

A33.3172 ->[A33.0110] 1 BOLT B7

A33.3173 ->[A33.0110] 1 ADJUSTING SCREW C7

A33.3174 ->[A33.0110] 1 SEALING SCREW B7

A33.3175 ->[A33.0110] 1 BALL B7

[A33.5101] ->[A33.0103] 1 SEALING HOUSING C3

A33.5105 1 BASE PLATE E3

A33.5109 ->[A33.0104] 1 DIE AND CUTTER SUPPORT C2

A33.5110 *1 CUTTER 0,7 MM D2

A33.5117 1 ROLLER C2

A33.5118 1 PARALLEL PIN D1

A33.5119 2 GUIDE C3

A33.5120 1 ECCENTRIC SHAFT B2

A33.5121 1 EYE C2

A33.5122 ->[A33.0105] 1 BEARING PICK-UP ATTACHMENT C1

A33.5123 1 GUIDE GIB C2

A33.5124 1 GUIDE GIB C2

A33.5125 1 SIDE PLATE E2

A33.5126 1 EJECTOR E3

A33.5127 1 EJECTOR SCREW E3

A33.5128 ->[A33.0106] 1 SEALING HANDLE A5

A33.5129 1 EJECTOR B2

A33.5133 1 STRAP STOP B2

[A33.5201] ->[A33.0107] 1 ROCKER D6

A33.5203 ->[A33.0107] 1 SPACER PIECE D6

A33.5204 1 SEALING WASHER D7

A33.5205 ->[A33.0108] 1 GEAR BODY B5

[A33.5206] ->[A33.0108] 1 WHEEL SHAFT B5

A33.5209 ->[A33.0108] 1 SPUR WHEEL C5

A33.5210 ->[A33.0108] 1 INTERMEDIATE WHEEL D5

A33.5211 ->[A33.0108] 1 TENSION SHAFT D5

A33.5212 ->[A33.0108] 1 BODY BASE D5

A33.5216 *1 TENSIONING WHEEL E6

A33.5220 1 STRAP GUIDE E5

A33.5221 ->[A33.0109] 1 END COVER E5

A33.5223 ->[A33.0110] 1 DRIVER B6

A33.5225 2 SUPPORTING DISK E5+

A38.3123 *1 DIE HALF D2

A38.3124 *1 DIE HALF D2

A38.3129 *1 GRIPPER D4

Sales and Service 877-862-6699

WWW.TRADITIONALTOOL.COM

Table des matières

Autres manuels Traditional Tool Repair Outils

Traditional Tool Repair

Traditional Tool Repair MUL-370 Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair DTF-125 Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair DTF-76 Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair DSA-116 Mode d’emploi

Traditional Tool Repair

Traditional Tool Repair DTF-56 Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair STTR Manuel utilisateur

Traditional Tool Repair

Traditional Tool Repair JK1219 Manuel de service

Traditional Tool Repair

Traditional Tool Repair DTP-100UL Manuel utilisateur

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser