1.0 GETTING STARTED
1.1 What’s included
TrackPIN Switch (A)
TrackPIN Keypad (B)
TrackPIN Hub (C)
Hub power cord (D)
Switch power cord (E)
Ethernet cable (F)
Position sensor (G)
Note: Before you install your hardware, make sure to set up
your TrackPIN™ account.
1.2 Creating Your Account
1. Log on to app.trackpin.com and click on “+New/Setup”.
2. Enter your email, password and zip code in the provided fields.
3. Enter the key number found on the Hub (C)
4. Click on “Create Account.”
2.0 INSTALLING YOUR HUB
When installing your Hub please be mindful of the location you choose for it.
The Hub transmits and receives a radio frequency signal that can be blocked by
metal objects and other electronic devices. To ensure best performance and
maximum range, avoid metal objects between your Hub and gate and allow as
much distance as possible between your Hub and other electronic devices.
Image 3.2
1. Insert the Hub power cord (D) into the power port on the Bottom
side of the Hub (C) and plug the power cord (D) into an existing
power outlet.
2. Connect one end of an Ethernet cable (F) into an open Ethernet port
on your internet router, then insert the other end of the Ethernet
cable into the Ethernet port located on the bottom side of the Hub.
Note: Once the Hub is connected to a power source, you should see a
blue light indicating that the Hub is now ON.
3.0 INSTALLING YOUR SWITCH
3.1 Mounting Your Switch
When choosing a location to mount your Switch we advise you to
make sure the LED light is easily visible. If you ever contact customer
support, the agent will ask what the status of the LED light is.
Note: For your safety, unplug/ disconnect power to the Gate Operator
before installation to prevent the motor from accidentally operating
during installation.
Mount your Switch using one of the following two methods.
1. Locate a spot near the Gate Operator and mark the position of the
two screw holes of the switch onto the mounting surface. Drill out
the holes then press a wall anchor into each hole. Mount your
Switch (A) and insert two screws to fasten it to the anchors.
2. Secure your Switch (A) to the existing gate pedestal, gate operator
or bracket using the adhesive tape or supplied screws.
Make sure the Switch and wires are clear of any moving parts on the
Gate Operator and drive assembly!
3.2 Connecting your Switch to the Gate Operator
Note: The order in which you connect your Switch connecting wires is
not important as long as they are inserted into the common and open
ports of the gate operator.
1. Identify if your gate requires a normally open or normally closed relay
and install wires in the appropriate order (refer to #2 in image 3.1).
2. Connect the wires from #2 to the common and open ports on the
gate controller (refer to image 3.2)
3. Wire one end of your Switch power cable (E) into the Switch (A)
(Refer to #1 in image 3.1 and diagram 3.2) and the other end into a
power source. Once connected to power, the LED light on your
Switch will light up showing power is on.
4. Connect the battery backup (#4 on image 3.1), this step is optional.
Note: The Switch can receive power from the supplied power adapter
or from any 12-24 volt 1-amp gate control panel
3.3 Installing your Door Position Sensor (Option A)
1. Close your Gate.
2. Locate an unobstructed path to run the wiring for your door
position sensor from your mounted Switch (A) to the side of
your Gate.
3. Clean and dry a small area on the side surface of your Gate.
4. Peel the protective film from the non-wired door sensor’s (D)
adhesive tape and firmly press the sensor onto the Gate.
5. Place the wired sensor (K) on the Gate frame an inch or less from
the non-wired sensor (D) while ensuring that the non-wired sensor
(D) can clear the wired sensor (K) when the gate opens.
6. Clean and dry the mounting location of the wired sensor (K)
7. Peel off the film from the wired sensor’s (K) adhesive pad and
firmly press the sensor onto the Gate frame.
8. As an alternative, you may choose to mount these sensors with
the supplied mounting screws and anchors.
9. Lead the wire from the wired sensor to your Switch
10. Plug the wire from the wired sensor into the sensor connector
(refer to #3 on the image above). The order of the wires is not
important. (R1IN and GND on the board)
Note: Please make sure your Switch and wires are clear of any moving
parts on the Gate Operator and drive assembly!
4.0 INSTALLING YOUR KEYPAD
4.1 Mounting Your Keypad
If you have an existing keypad—
1. Remove your existing keypad.
2. Where possible, line up the existing screw holes with the
mounting holes in your TrackPIN™ Keypad.
If you do not have an existing keypad—
1. Hold the TrackPIN Keypad up to the wall/pedestal and mark
where you would like to mount your new Keypad
2. Drill a small hole for each of the supplied wall anchors.
i. Insert the anchors into the new holes, if required.
ii. Insert the supplied screws into the holes/anchors and
tighten them.
4.2 Installing the Batteries
1. Unlock and lower the front of the keypad
2. Insert batteries into battery holder.
3. Replace the keypad face and lock the keypad.
Note: To verify that the keypad is ON, press any key and watch the
lights illuminate. If the keypad is in direct sunlight, the illuminated lights
may appear dim.
5.0 PROGRAMMING YOUR FIRST PIN
5.1 Creating and Testing Your PIN on the Keypad
1. Navigate to the MY PINs menu and select “+ New PIN”.
2. A random PIN will be automatically created. If desired, you may
re-enter any four-digit number of your choice into the provided
field.
3. Name the PIN by clicking in the name field and typing. Once you
have created a name select SAVE. After 5-15 seconds your new
PIN will be available for use.
4. Enter your new four-digit PIN onto your Keypad to open or close
your gate.
5.2 Verifying TrackPIN™ Logging
After entering your four-digit PIN on the keypad, a log of your activity
will appear on the home screen/ activity log of your TrackPIN™
account.
Note: A screen refresh may be required.
Congratulations!
Your TrackPIN™ system is now ready for use.
110
Common
Open
Gate Operation Relay
TrackPIN Gate Switch
Power 12/24v AC/DC
NC
COM
Use power on board
or supplied wall transformer
Power
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
GATE CONTROL
PANEL
TrackPIN™ Switch/Bridge
Position
Sensor
GND
R1IN
8
