TP-Link JetStream T1500G-10MPS Manuel utilisateur

Business Networking Solution

Installation Guide

JetStream 8-Port Gigabit Smart PoE+Switch

with 2 SFP Slots

T1500G-10MPS

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам

нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

• When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the

product or the power adapter from the power source.

• Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and

voiding the limited warranty. If you need service, please contact us.

• Avoid water and wet locations.

BSMI Notice

安全諮詢及注意事項

• 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

• 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

• 注意防潮，請勿將水或其他液體潑灑到本產品上。

• 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

• 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

• 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

• 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採

取某些適當的對策。

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

Explanation of the symbols on the product label

Symbol Explanation

AC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical

and electronic equipment (WEEE). This means that this product must

be handled pursuant to European directive 2012/19/EU in order to be

recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling

organization or to the retailer when he buys a new electrical or electronic

equipment.

Related Document

This Installation Guide is also available in PDF on our website. To obtain the

latest documentation and product information, please visit the official website:

http://www.tp-link.com

About this Installation Guide

This Installation Guide describes the hardware characteristics, installation

methods and the points that should be attended to during the installation. This

Installation Guide is structured as follows:

Chapter 1 Introduction. This chapter describes the external components of

the switch.

Chapter 2 Installation. This chapter illustrates how to install the switch.

Chapter 3 Lightning Protection. This chapter illustrates how to prevent

lightning damage.

Chapter 4 Connection. This chapter illustrates how to do the physical

connection of the switch.

Appendix A Troubleshooting.

Appendix B Specifications.

Audience

This Installation Guide is for:

Network Engineer Network Administrator

Conventions

■The figures in Chapter 2 to Chapter 4 are for demonstration purposes only.

Your switch may differ in appearance from that depicted.

■This guide uses the specific formats to highlight special messages. The

following table lists the notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may result

in device damage.

Remind to take notice. The note contains the helpful information for a

better use of the product.

Contents

Chapter 1 Introduction ——————————— 01

1.1 Product Overview ...........................................................01

1.2 Appearance.......................................................................01

Chapter 2 Installation ——————————— 05

2.1 Package Contents ..........................................................05

2.2 Safety Precautions.........................................................05

2.3 Installation Tools..............................................................07

2.4 Product Installation ........................................................08

Chapter 3 Lightning Protection ——————— 10

3.1 Cabling Reasonably........................................................10

3.2 Connect to Ground.........................................................12

3.3 Equipotential Bonding...................................................13

3.4 Use Lightning Arrester..................................................14

Chapter 4 Connection ——————————— 16

4.1 Ethernet Port ....................................................................16

4.2 Verify Installation.............................................................16

4.3 Power On............................................................................16

4.4 Initialization........................................................................17

Appendix A Troubleshooting ———————— 18

Appendix B Specications ————————— 19

Smart PoE+ Switch

Introduction

Chapter 1 Introduction

1.1 Product Overview

T1500G-10MPS is compliant with the IEEE802.3 Ethernet protocols.

The switch is equipped with powerful management interface, via which system, port,

network, VLAN and priority can be configured. They provide a variety of service

features and multiple powerful functions with high security. The EIA-standardized

framework and smart configuration capacity can provide flexible solutions for a

variable scale of networks. QoS and IGMP snooping/filtering optimize voice and

video application. SNMP, RMON, WEB Log-in bring abundant management policies.

T1500G-10MPS integrates multiple functions with excellent performance, and are

friendly to manage, which can fully meet the need of the users demanding higher

networking performance.

T1500G-10MPS Smart PoE+ Switch is also a Power Sourcing Equipment (PSE*).

All the fast Ethernet RJ45 ports on the switch support Power over Ethernet (PoE*)

function, which can automatically detect and supply power with those powered

devices (PDs*) complying with IEEE 802.3af and IEEE 802.3at.

*PSE: a device (switch or hub for instance) that provides power through an Ethernet

cable.

*PoE: This technology describes a system to transmit electrical power, along with

data, to remote devices over standard twisted-pair cable in an Ethernet.

*PD: a device powered by a PSE and thus consumes energy. Examples include

powering network cameras, wireless LAN access points, IP telephones, network

hubs, embedded computers etc.

1.2 Appearance

■Front Panel

The front panel of T1500G-10MPS is shown as the following figure.

Reset

LEDs

10/100/1000Mbps RJ45 Port and PoE Port

LED Mode Switch Button

SFP Port

Figure 1-1 Front Panel of T1500G-10MPS

Smart PoE+ Switch

Introduction

LEDs

T150 0 G-10 MPS has an LED mode switch button which is for switching the LED

status indication. When the Speed LED is on, the port LED is indicating the data

transmission status. When the PoE LED is on, the port LED is indicating the power

supply status. By default, the Speed LED is on. Pressing the mode switch button,

the Speed LED will turn o and the PoE LED will light up. Then the PoE LED will turn

o after being on for 60 seconds and the Speed LED will light up again.

When the Speed LED is on, the port LED is indicating the data transmission status.

LED Status Indication

PWR

On The switch is powered on

Off The switch is powered off or power supply is

abnormal

Flashing Power supply is abnormal

SYS Flashing The switch works properly

On/Off The switch works improperly

FAN Green All the fans work properly

Yellow Not all the fans work properly

PoE MAX

On The remaining PoE power≤7W

Flashing The remaining PoE power keeps ≤7W after

this LED is on for 2 minutes

Off The remaining PoE power>7W

Speed or PoE

Green On A 1000Mbps device is connected to the cor-

responding port, but no activity

Flashing Data is being transmitted or received

Yellow On A 10/100Mbps device is connected to the cor-

responding port, but no activity

Flashing Data is being transmitted or received

Off No device is connected to the correspond-

ing port

SFP1, SFP2

Green On A 1000Mbps device is connected to the

corresponding port, but no activity

Flashing Data is being transmitted or received

Yellow On A 10/100Mbps device is connected to the

corresponding port, but no activity

Flashing Data is being transmitted or received

Off No device is connected to the correspond-

ing port

Smart PoE+ Switch

Introduction

When the PoE LED is on, the port LED is indicating the power supply status.

LED Status Indication

PWR

On The switch is powered on

Off The switch is powered off or power supply is

abnormal

Flashing Power supply is abnormal

SYS Flashing The switch works properly

On/Off The switch works improperly

FAN Green All the fans work properly

Yellow Not all the fans work properly

PoE MAX

On The remaining PoE power≤7W

Flashing The remaining PoE power keeps ≤7W after

this LED is on for 2 minutes

Off The remaining PoE power>7W

Speed or PoE

Green

On The port is supplying power normally

Flashing The supply power exceeds the corresponding

port's maximum power

Yellow On Overload or short circuit is detected

Flashing Power-on self-test has failed

Off No PoE power supply is provided on the port

SFP1, SFP2

Green On A 1000Mbps device is connected to the

corresponding port, but no activity

Flashing Data is being transmitted or received

Yellow On A 10/100Mbps device is connected to the

corresponding port, but no activity

Flashing Data is being transmitted or received

Off No device is connected to the correspond-

ing port

Reset

With the switch powered on, press Reset button for 5 seconds to reset the software

setting to its factory default settings.

10/100/1000Mbps RJ45 Port and PoE Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding Speed or PoE LED.

SFP Port

Designed to install the SFP module. T1500 G -10 MPS features 2 SFP transceiver

ports.

Smart PoE+ Switch

Introduction

■Rear Panel

The rear panel of T1500G-10MPS is shown as the following figure.

Kensington Security Slot

Power Socket

Grounding Terminal

Figure 1-2 Rear Panel of T1500G-10MPS

Kensington Security Slot

Secure the lock (not provided) into the security slot to prevent the device from

being stolen.

Power Socket

Connect the female connector of the power cord here, and the male connector

to the AC (Alternating Current) power outlet. Please make sure the voltage of the

power supply meets the requirement of the input voltage.

Grounding Terminal

The switch already comes with lightning protection mechanism. You can also

ground the switch through the PE (Protecting Earth) cable of AC cord or with

Ground Cable. For detailed information, please refer to Chapter 3 Lightning

Protection.

Caution: Please use the provided power cord.

Autres manuels pour JetStream T1500G-10MPS

Table des matières

Autres manuels TP-Link Changer

TP-Link

TP-Link JetStream T1600G-28TS Manuel utilisateur

TP-Link

TP-Link TL-SG605E Manuel utilisateur

TP-Link

TP-Link TL-SL2428 Manuel utilisateur

TP-Link

TP-Link JetStream TL-SG5428 Manuel utilisateur

TP-Link

TP-Link TL-SG105 Manuel utilisateur

TP-Link

TP-Link T2500G-10MPS Manuel utilisateur

TP-Link

TP-Link KS205 Manuel utilisateur

TP-Link

TP-Link JetStream T2700G-28TQ Mode d’emploi

TP-Link

TP-Link TL-SF1005D Manuel utilisateur

TP-Link

TP-Link TL-SL5428E Manuel utilisateur

TP-Link

TP-Link Tapo S200D Manuel utilisateur

TP-Link

TP-Link UH400 Manuel utilisateur

TP-Link

TP-Link Jetstream Series Manuel utilisateur

TP-Link

TP-Link TL-SG1005P Manuel utilisateur

TP-Link

TP-Link JetStream T1500G-8T Manuel d'instructions d'installation

TP-Link

TP-Link tapo S505D Manuel utilisateur

TP-Link

TP-Link TL-SG608E Manuel utilisateur

TP-Link

TP-Link T2500G-10TS Mode d’emploi

TP-Link

TP-Link KS205 Manuel utilisateur

TP-Link

TP-Link TL-POE150S Manuel utilisateur

TP-Link

TP-Link TL-SG2424P Manuel utilisateur

TP-Link

TP-Link JetStream TL-SG2008 Manuel utilisateur

TP-Link

TP-Link TL-SG1005D Manuel utilisateur

TP-Link

TP-Link TL-SF1005D Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur