TP-Link TL-R402M Manuel

Rev. 1.3 – 01/07/2009

TP Link Router Basic Setup

Introduction

The TP-Link #TL-R402M Cable/DSL Router is a broadband router. Detailed information is on

the vendor’s web site at http://www.tp-link.com.

A router assigns Dynamic Host Configuration Protocol (DHCP). This means the router

assigns Internet Protocol (IP) addresses to all connected equipment configured to request on.

The two basic rules for DHCP:

•Only one router can be active in the same group of connected equipment.

•Each equipment item must have a unique IP address. If two devices get the same IP,

erratic behavior will result – most often the duplicate IP will fail to communicate.

By default, DHCP is on in this router.

Package Contents:

•TP-Link TL-R402M Router

•Power Adapter

•Quick Installation Guide

•Resource CD

You must own or purchase 1 network cable; the most common is a 6 foot

length. While sold under various names, make sure it is Cat5E type, with the

RJ-45 connectors.

Installation Planning

Consult the TP-Link Quick Installation Guide for an overview. The TP-Link TL-R402M unit is a

broadband router, so it must work with your cable or dsl modem. Your existing Cable or DSL

modem must also have one Ethernet port, which is probably connected to your PC.

Double-check that your internet works with the existing Cable or DSL modem before

you try to add the router. If you don’t have functioning internet before proceeding,

contact your Internet Service Provider (ISP).

Rev. 1.3 – 01/07/2009

Home Installation of the TP-Link Router

1. Power down all existing equipment (computer, cable/dsl modem, etc.).

2. Locate a suitable location for the TP-Link router.

3. On your cable or dsl modem, find the Ethernet port

and follow the (network) cable from the port of the

modem to the network card on the PC.

4. Unplug the PC end of the cable, and plug it into the WAN port on the TP-Link router.

[Note: you use the WAN port if you will leave DHCP on and use this device as a router.]

5. Now take the extra Ethernet cable (from page 1), and plug one end into the network port

on the PC (where you just removed your modem’s cable in step 4 above).

6. Plug the other end of the extra cable into any open LAN port on the TP-Link router (see

picture in step #4). Tip: It can keep you organized to use port #1, but this isn’t strictly

necessary.

7. Connect the A/C adapter to the router, and it will power on.

8. Power on the primary PC and the cable/dsl modem.

9. Recheck that your basic internet still works on the PC.

10. Proceed to the Weather Direct gateway installation, if that is your goal

(www.weatherdirect.com).

Note: If you have internet service problems at this point, the two most common errors are:

a) a mistake in the cabling, so check the connections in steps 1-9 again or

b) missing that DHCP is enabled on either the cable/dsl modem or some other routing

device. Only one device can serve DHCP, so competing devices need DHCP disabled.

If you have any additional needs, you will need to consult the TP-Link Users Guide on the CD

that came with the router or our Router Trouble-Shooting handout.

LAN

ports

Autres manuels pour TL-R402M

1

Table des matières

Autres manuels TP-Link Routeur réseau

TP-Link

TP-Link Archer C20 Manuel utilisateur

TP-Link

TP-Link Archer XR500v Manuel utilisateur

TP-Link

TP-Link AC1600 Manuel utilisateur

TP-Link

TP-Link Archer C90 Manuel utilisateur

TP-Link

TP-Link TL-R4000+ Manuel utilisateur

TP-Link

TP-Link Archer C5400 Manuel utilisateur

TP-Link

TP-Link 8840 Manuel utilisateur

TP-Link

TP-Link Deco W6000 Manuel utilisateur

TP-Link

TP-Link TL-WA820RE Manuel utilisateur

TP-Link

TP-Link Archer C20 Manuel utilisateur

TP-Link

TP-Link CR1900 Manuel utilisateur

TP-Link

TP-Link Archer VR600 Manuel utilisateur

TP-Link

TP-Link TD-8841T Manuel utilisateur

TP-Link

TP-Link TD-8816 Manuel utilisateur

TP-Link

TP-Link TD-W300KIT Manuel utilisateur

TP-Link

TP-Link SafeStream TL-R480T+ Manuel utilisateur

TP-Link

TP-Link Archer AX53 Manuel utilisateur

TP-Link

TP-Link JetStream L2 Lite TL-SG3210 Manuel utilisateur

TP-Link

TP-Link Archer C1900 Manuel utilisateur

TP-Link

TP-Link VX230v Manuel utilisateur

TP-Link

TP-Link SafeStream TL-ER6020 Manuel utilisateur

TP-Link

TP-Link Deco Wi-Fi 6 Manuel utilisateur

TP-Link

TP-Link Deco BE16000 Manuel utilisateur

TP-Link

TP-Link TP-TL-WR1043N Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur