Toyota 2013 Prius Manuel utilisateur

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 1"

SoftTouch Navigation System

250-7613 2012-2013 Toyota Camry Installation Instructions

General Applicability:

Toyota – 2012-2013 Prius/Prius V, 2013 Venza, 2013 Avalon, 2013 Highlander, 2013 Tacoma

For video installation instructions, please visit us online at www.rostra.com.

Parts Identification

Page 1

Vehicle Preparation

Page 3

Programming Switch Settings

Page 3

Installation

Page 4

Parts Identification

Item

Qty.

Description

Navigation interface module

LCD IN harness

TP-IN harness

Hardware service parts (VHB tape, metal plate)

Vehicle interface harnesses

Stylus

GPS antenna with magnetic base

GPS speaker

Navigation interface board

LCD-IN/TP-IN Extension Harness

Form #5420, 3-20-2013

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 2"

STOP

YOU MUST READ THESE WARNINGS AND NOTICE BEFORE PRODUCT

HANDLING AND INSTALLATION!

PRODUCT AND VEHICLE APPLICATION WARRANTY DISCLAIMER

WARNING ! The Navigation Electronic Components are sensitive to Electro-

Static Discharge (ESD). DO NOT HANDLE THE NAVIGATION ELECTRONIC

COMPONENTS WITHOUT PROPER ESD GROUNDING DURING

INSTALLATION. FAILURE TO USE PROPER ESD PROTECTION WHEN

HANDLING THE NAVIGATION COMPONENTS WILL VOID THE PRODUCT

WARRANTY.

WARNING ! Installation of this Navigation Electronics product in the vehicle

radio head unit must be performed by a professional technician that is experienced

with proper work methods, ESD handling requirements, and knowledgeable of

specific procedures for radio disassembly, Navigation Electronics installation, and

re-assembly of the vehicle Radio Head Unit as well as proper handling

requirements of all components involved. FAILURE TO FOLLOW PROPER

DISASSEMBLY, INSTALLATION, AND REASSEMBLY PROCEDURES AND

PROPER COMPONENT HANDLING REQUIREMENTS MAY RESULT IN

IRREVERSIBLE DAMAGE TO THE VEHICLE RADIO HEAD UNIT AND/OR

THE NAVIGATION ELECTRONICS AND WILL VOID THE PRODUCT

WARRANTY!

WARRANTY DISCLAIMER NOTICE! Radio removal, disassembly, installation

of Navigation Electronics, and Radio re-assembly / re-installation is the

responsibility of the installer, not Rostra Precision Controls, Inc. It is recommended

that you contract a professional installer that is experienced with proper work

methods involving electronics and knowledgeable of specific procedures for radio

disassembly, Navigation Electronics installation, and re-assembly / re-installation of

the Radio Head Unit in the vehicle. INSTALLATION DAMAGE TO THE

VEHICLE RADIO HEAD UNIT IS NOT THE RESPONSIBILITY OF ROSTRA

PRECISION CONTROLS, INC. AND IS EXPRESSLY NOT COVERED UNDER

THE PRODUCT WARRANTY.

Rostra Precision Controls, Inc. 2/5/2013

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 3"

WARNING

To avoid dangerous distractions that may lead to an accident, the driver should never operate

the system while the vehicle is in motion. Before installing this product, the seller should

inform the end-user of proper use and compliance with the proper instructions and all state and

federal laws.

Vehicle Preparation

Before beginning your installation, familiarize yourself with the installation instructions and the

SoftTouch Navigation system components.

To ensure your safety, (A) apply the emergency brake and (B) read this entire manual before

beginning.

CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes before

beginning installation, to avoid unintended air bag deployment. Note and record any anti- theft

radio codes prior to disconnecting.

Default Programming Switch (Dip Switch) Settings

Default Programming Switch Settings

1 – Off 2 – Off 3 – Off 4 – Off 5 – Off 6 – Off 7 – Off 8 – Off

Factory or Aftermarket Camera Settings

To use an aftermarket camera – Place switch #1 in OFF position.

To use the vehicle’s factory camera – Place switch #1 in ON position.

Visit www.rostra.com to view all compatible backup cameras!

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 4"

Installation

Remove air vent to access upper radio screws.

Remove trim pieces to access lower screws.

Remove four screws securing radio/screen unit.

Release connectors from upper dash trim.

Remove upper dash trim from radio.

Gently tilt radio away from dashboard.

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 5"

Release harnesses from rear of radio/screen.

Lift screen away from dashboard.

Navigation Interface Module Installation

ESD Warning: Do not handle the navigation interface circuitry without taking proper electrostatic discharge

precautions making sure both the installer and navigation unit are properly grounded before touching any interior

radio or navigation components. The warranty on this product is immediately voided if these precautions are not

taken and the navigation unit and/or radio are damaged due to electrostatic discharge.

Remove radio brackets from each side.

Remove screws securing the screen housing.

Use a trim tool to release the screen tabs and then

lift the housing to access the radio’s interior.

Remove the backing from the double-sided tape of

the nav board and secure it to the metal cover below

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 6"

Installer note: To gain more flexibility while

installing the navigation interface board in the next

steps, you can release the tabs to remove the ribbon

cables attached the main body to the screen.

Disconnect the large brown ribbon cable from the

factory board and insert the ribbon cable from the

nav interface board. Then insert the brown ribbon

cable into the nav interface board.

Disconnect the small brown ribbon cable from the

factory board and insert the ribbon cable from the

nav interface board. Then insert the brown ribbon

cable into the nav interface board.

Place one of the included ESD tape strips over any

exposed metal underneath the small navigation

interface board.

Place the second ESD tape strip over nav board.

Use included cloth tape over ESD tape to secure it.

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 7"

Connect LCD-IN/TP-IN Extension Harness to the

navigation interface board.

Route the LCD-IN/TP-IN Extension Harness from

the radio’s interior through the opening in the back

of the housing.

Attach the included metal plate to the interior of the

vehicle’s dashboard using the supplied double-sided

tape.

Place the included GPS antenna atop the mounted

metal plate and allow its magnetic base to secure it

to the plate.

Located the threaded connector of GPS antenna.

Thread GPS antenna onto navigation module.

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 8"

Connect the included speaker to the speaker

extension harness.

Connect the speaker extension harness to the

navigation module.

Using the supplied cable ties, mount the navigation

speaker to the dashboard support brackets behind

and below the radio unit.

Using the supplied alcohol pad, throughly clean the

underside of the factory radio and navigation unit.

Once clean, press the supplied VHB tape firmly to

the bottom side of the navigation module.

Peel the protective layer from the VHB tape making

sure no debris comes into contact.

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 9"

Connect the yellow and pink color-coded TP-IN and

LCD OUT harnesses to the rear of the navigation

module.

Firmly press the navigation module to the bottom

side of the factory radio allowing the VHB to

adhere the two together.

Connect the power harness from the supplied t-

harness to the POWER connector of the navigation

module.

Connect the radio interface plug from the supplied

t-harness to the backside of the radio.

Reconnect all previously disconnected harness from

the backside of the factory radio.

Radio component replacement is the reverse of

removal.

Navigation System Testing

Rostra Precision Controls, Inc. - 2519 Dana Dr. - Laurinburg, NC 28352 - 800-782-3379 - rostra.com

Page 10"

Turn on the vehicle’s ignition.

Press the steering wheel’s phone hang up button for

2 seconds to switch to the navigation interface.

Once the steering wheel’s phone hang up button has

been pressed, the navigation screen should be

displayed.

Autres manuels pour 2013 Prius

Ce manuel convient aux modèles suivants

Autres manuels Toyota Système de navigation automobile

Toyota

Toyota TNS 300 Manuel utilisateur

Toyota

Toyota DRG Manuel utilisateur

Toyota

Toyota AVALON - 2011 Manuel utilisateur

Toyota

Toyota 2009 4Runner Manuel utilisateur

Toyota

Toyota Tundra 2014 Manuel utilisateur

Toyota

Toyota TNS 300 Manuel utilisateur

Toyota

Toyota 2016 ENTUNE AUDIO Manuel utilisateur

Toyota

Toyota Verso TNS510 Manuel utilisateur

Toyota

Toyota Prius Navi Manuel utilisateur

Toyota

Toyota TNS 200 Manuel utilisateur

Toyota

Toyota TNS600 Manuel utilisateur

Toyota

Toyota 4Runner 2021 Manuel utilisateur

Toyota

Toyota 2014 Camry Manuel utilisateur

Toyota

Toyota TNS 200 Manuel utilisateur

Toyota

Toyota Aygo X-NAV Manuel utilisateur

Toyota

Toyota Hilux 2017 Manuel utilisateur

Toyota

Toyota RAV4 2011 Manuel utilisateur

Toyota

Toyota HIGHLANDER 2014 Manuel utilisateur

Toyota

Toyota AYGO X-NAV RHD Manuel utilisateur

Toyota

Toyota TNS300 RAV4 NAVIGATION SYSTEM Manuel utilisateur

Toyota

Toyota TNS 300 Manuel utilisateur

Toyota

Toyota RAV4 2011 Manuel utilisateur

Toyota

Toyota TNS 300 Manuel utilisateur

Toyota

Toyota MyT Multimedia Manuel utilisateur

Manuels Système de navigation automobile populaires d'autres marques

Clarion

Clarion Navigation In-Car Entertainment Manuel utilisateur

Rosen

Rosen DP-1001 Manuel utilisateur

Alpine

Alpine INE-W970HD Manuel utilisateur

Skoda

Skoda AMUNDSEN+ Manuel utilisateur

Blaupunkt

Blaupunkt TravelPilot DX-N Manuel utilisateur

Pioneer

Pioneer MZ360500EX Manuel utilisateur

Sanyo

Sanyo NVM-4030 - Easy Street - Automotive GPS... Manuel utilisateur

Kenwood

Kenwood DNN991HD Manuel utilisateur

AvMap

AvMap Geosat 2C Manuel utilisateur

Eonon

Eonon GE01B Manuel utilisateur

Pioneer

Pioneer AVIC-Z920DAB Manuel utilisateur

Nextar

Nextar M3-MX - Automotive GPS Receiver Manuel utilisateur

Furrion

Furrion NV2200 Manuel utilisateur

Mio

Mio MOOV 200-Series Manuel utilisateur

Prestigio

Prestigio GeoVision 5150 Manuel utilisateur

Hummer

Hummer 2006 H3 Manuel utilisateur

Magellan

Magellan Maestro 4210 - Automotive GPS Receiver Guide de configuration

Garmin

Garmin StreetPilot c510 Manuel utilisateur