Touchboards Peerless CPA100WALLARM Mode d’emploi

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

1 of 12

Installation and Assembly: Hitachi Short Throw Wall Arm

Model: CPA100WALLARM

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

Maximum Load Capacity: 50 lb (22.7 kg)

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

2 of 12

NOTE: Read entire instruction sheet before you start installation and assembly.

• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings

containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please

callPeerlesscustomercareat1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

• Neverexceed the Maximum Load Capacity. See pageone.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edgeto edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tightenscrews firmly,but do not overtighten. Overtightening candamagethe items, greatly reducing their holding

power.

• Thisproductis intended for indoor use only. Use of this product outdoorscould leadtoproduct failure and personal

injury.

• Thisproduct was designed and intended to be mounted tothefollowing supporting surfaces checked below with the

hardware included in this product as specified in the installation sheet.To mount this product to an alternative support-

ing surface, contact Peerless customer care at 1 800 865-2112.

• This product was designed to be installed on the following wall construction only;

WALLCONSTRUCTION ADDITIONALHARDWAREREQUIRED

xWoodStud None

xWoodBeam None

xSolidConcrete None

xCinderBlock None

xMetalStud Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

Brick ContactCustomer Service

Otheror unsure? ContactCustomer Service

WARNING

Tools Needed for Assembly

•studfinder ("edge to edge" stud finder is recommended)

•phillipsscrewdriver

•drill

•1/4" bit for concrete and cinder block wall

•1/2" bit for metal stud wall

•5/32" bit for metal or wood stud wall

•level

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

3 of 12

Description Qty. Part #

Aslide plate 1 055-1821

Bprojector mount assembly 1 055-1803

C#10-32 x 3/8" serrated washer head socket pin screw 2 520-1151

D#10-32 x 1/4" socket pin screw 1 520-1196

E5/32" (4 mm) security allen wrench 1 560-9646

F6.5 ID flat washer 2 540-1078

G#14 x 2.5" wood screw 4 5S1-015-C03

HAlligator®anchor 4 590-0097

I3/32" (2 mm) security allen wrench 1 560-1097

Jwall arm 1 055-1820

Kwall plate 1 055-1818

Ladapter plate 1 055-1822

M1/4-20 x 1" hex head screw 2 520-1606

N1/4" ID spacer 2 560-1723

O0.509" ID spacer 2 590-1270

P0.376 ID shoulder spacer 2 590-1269

Qrectangle plug 1 590-1302

Rcircle plug 2 590-1301

S2" rubber grommet 1 560-1726

T1.75" rubber grommet 1 560-1168

UM6 x 12 mm serrated washer head socket pin screw 8 510-1050

Vwasher fender 4 540-1008

Wvinyl trim 1 600-1012

X0.25" spacer 4 590-1050

Parts List

Partsmay appear slightly different than illustrated.

Beforeyou begin, make sure all parts shown are included with your product. B

JK L MN

S T

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

4 of 12

NOTE: Use the chart (see fig 1.1) below to determine the placement of projector in relation to mounting location of

wall arm. Chart numbers will have a 3% discrepancy due to the optics of the projector. Prior to installing projector,

physically test the projection size and distance while having the actual projector in the desired location before

installing, this will determine the exact mounting position.

Projector Position

fig. 1.1

SCREEN/WHITEBOARD

3.65

(X)

CENTER OF

WALLARM

CENTER OF

LENS

fig. 1.2

* The distance from the bottom of the

projector to the top of the screen.

(Z)

THROWDISTANCE:(Y)

(Thedistancefromprojectoredgetoscreensurface)

3.9" (9.9 cm)

NOTE: Lens is not centered to the wall arm

14.8" (37.5 cm)

Screen size

(

)

inch inch cm inch cm

63 5.9 14.9 13.0 33.0

70 8.0 20.3 14.0 35.5

77 10.0 25.4 15.0 38.1

80 11.0 27.9 15.5 39.4

90 14.0 35.5 16.9 42.9

100 16.9 42.9 18.4 46.7

Throw Distance

(

)

Image Offset *

(

)

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

5 of 12

Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based

on their edges, draw a vertical line down each stud’s center. Place wall plate (K) on wall as a template. Level plate,

and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerline. Drill

four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate (K) is level, secure it using four

#14 x 2.5" wood screws (G) and fender washers (V) as shown in figure 2.1.

Installation to Wood Stud Wall

• Installermust verify that the supporting surface will safely support the combined load of the equipment andallattached

hardwareandcomponents.

• Tightenwood screws so that wall plate is firmly attached, but donotovertighten.Overtightening can damage the

screws,greatly reducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is

highlyrecommended.

• Hardwareprovided is for attachment of mount throughstandardthickness drywall or plaster into wood studs.Installers

areresponsible to provide hardwarefor other types ofmountingsituations.

WARNING

fig. 2.1

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

6 of 12

Make sure that wall plate (K) is level, use it as a

template to mark four mounting holes. Drill four 1/4"

(6 mm) dia. holes to a minimum depth of 2.5" (65 mm).

Insert anchors (H) in holes flush with wall as shown

(right).Placewall plate over anchors and secure with

four #14 x 2.5" screws (G) and fender washers (V).

Level,thentightenallfasteners.

Installation to Solid Concrete or Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingout the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surface will safely support the combined load of the equipment and all attached hard-

wareand components.

WARNING

CONCRETE

SURFACE

Drill holes and insert anchors (H).

Place plate (K)over anchors (H) and secure with screws (G)

and fender washers (V).

Tighten all fasteners.

CUTAWAYVIEW

INCORRECT

CORRECT

wallplate

plaster/

drywall

concrete

wallplate concrete

plaster/

drywall

• Always attach concrete anchors directly to load-

bearingconcrete.

• Neverattach concrete anchorsto concrete covered

withplaster,drywall, or other finishing material. If

mountingto concrete surfaces coveredwitha finishing

surfaceis unavoidable, the finishing surfacemust be

counterboredas shown below.Be sureconcrete

anchorsdo not pull away from concrete when tighten-

ing screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

• Tighten screws so that wall plate is firmly attached,

butdo not overtighten.Overtightening candamage

screws,greatly reducing their holdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

SOLIDCONCRETE

CINDERBLOCK

• Always attach concrete anchors directly to load-

bearingconcrete.

• Neverattach concrete anchorsto concrete covered

withplaster,drywall, or other finishing material. If

mountingto concrete surfaces coveredwitha finishing

surfaceis unavoidable, the finishing surfacemust be

counterboredas shown below.Be sureconcrete

anchorsdo not pull away from concrete when tighten-

ing screws. If plaster/drywall is thicker than 5/8",

custom fasteners must be supplied by installer.

WARNING

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

7 of 12

Wall plate (K) can be mounted to single metal stud. Use a stud finder to locate the edges of the stud. Use of an

edge-to-edge stud finder is highly recommended. Based on it's edges, draw a vertical line down stud’s center. Place

wall plate on wall as a template. Level plate, and mark the center of the four mounting holes. Make sure that the

mounting holes are on the stud centerline. Drill four 1/2" holes through drywall and metal stud. NOTE: It may be

necessary to drill 5/32" pilot holes prior to drilling 1/2" holes.

Refer to instruction sheet included with Peerless accessory kit ACC 415 for metal studs to install togglers.

Loosely fasten wall plate (K) to wall using four 1/4-20 x 2-1/2" screws as shown in figure 2.2.

Level, hold, and then tighten all screws.

• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.

• Installermust verify that the supporting surface will safely support the combined load of the equipment andallattached

hardwareandcomponents.

WARNING

Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 415 Required)

TOGGLER

(NOTINCLUDED)

fig. 2.2

1/4-20 X 2-1/2"

PHILLIPSSCREWS

(NOTINCLUDED)

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

8 of 12

Hook wall arm (J) onto wall plate (K) as shown in

fig.3.2orfor additional vertical adjustment fig. 3.3.

Run cords through desired opening at this point.

fig. 3.3

SUPPORTING

SURFACENOT

SHOWNFOR

CLARITY

Disengageconnectionblockfromprojectormount

assembly (B)by unscrewing captive screw and sliding

out connection block as shown.

fig. 3.2

fig. 3.1

Place vinyl trim (W) onto bottom or top of wall plate (K)

where cords will be routed as shown in fig. 3.1.

Secure arm to wall plate (K) using four M6 x 12 mm

serrated washer head socket pin screws (U) as

shown in fig. 3.4.Cut 1.75" rubber grommet (T)in

half and place into half moons on top and bottom of

wall arm (J). Insert circle plug (R) or 2" rubber

grommet (S) into arm fig. 3.4.

3-2

CONNECTION

BLOCK

CAPTIVE

SCREW

fig. 3.4

1.75"RUBBER

GROMMET

(CUTINHALF)

1/2OF

GROMMET(T)

1/2OF

GROMMET(T)

SOR

3-2

3-1

NOTE: Ifcords inserted through top or bottom openings,use

vinyltrim. Otherwise insert cords throughsecondaryopenings

on wall face as shown in fig. 3.2 and 3.3.

Secondary

Openings

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

9 of 12

NOTE: Do not tighten 1/4-20 x 1" hex head screws (M) fully to allow for adjustment. Fasten projector mount

assembly (B) to wall arm (J) using two 1/4-20 x 1" hex head screws (M), 0.509" ID spacers (O), 1/4"ID spacers (N),

0.376 ID shoulder spacers (P) and slide plate (A) as shown in fig. 5.1 and 5.2. Insert rectangle plug (Q) into wall

arm (J) as shown in fig. 5.3. See fig. 1.1 and 10.1 for additional adjustment of image size. Securely tighten both 1/4-

20 x 1" hex head screws (M) after desired image size is obtained.

FRONT VIEW

fig. 5.1 fig. 5.2

fig. 5.3

ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

10 of 12

PROJECTOR

Attachadapter plate (L) to projector using four

M6 x 12 mm serrated washer head socket pin

screws (U) and 0.25" spacers (X).

NOTE: Shoulderof connection block indicates

theback of projector.

SHOULDER

CONNECTION

BLOCK

CONNECTION

BLOCK

NOTCHINDICATES

FRONTOF

PROJECTOR

SHOULDER

Attaching Adapter Plate to Projector

fig. 6.1

Align shoulder on connection block opposite notch in

adapter plate (L). Attach adapter plate (L) to

connectionblock from projector mount assembly (B)

using two #10-32 x 3/8" serrated washer head socket

pin screws (C) as shown in figure 6.1.

Table des matières

Autres manuels Touchboards Support et étagère

Touchboards

Touchboards Black Box Network Services NBDEP-12 Manuel utilisateur

Touchboards

Touchboards BALT T-LECT 85751 Manuel utilisateur

Touchboards

Touchboards PM2-S-XL Manuel utilisateur

Touchboards

Touchboards ACC320 Manuel utilisateur

Touchboards

Touchboards peerless-AV LCZ-2F430B Mode d’emploi

Touchboards

Touchboards LINK 55140 Manuel utilisateur

Touchboards

Touchboards peerless-AV SS560F Manuel utilisateur

Touchboards

Touchboards CHIEF FCI Manuel utilisateur

Touchboards

Touchboards PSD-VHS Manuel utilisateur

Touchboards

Touchboards 55282 Manuel utilisateur

Touchboards

Touchboards peerless-AV SR560M-AB Manuel utilisateur

Touchboards

Touchboards InVision 37108 Manuel utilisateur

Touchboards

Touchboards CHIEF PSMH2079 Manuel utilisateur

Touchboards

Touchboards PANA-103MTV Mode d’emploi

Touchboards

Touchboards Dewey DCS1A Manuel utilisateur

Touchboards

Touchboards peerless-AV PRS-KIT0811 Mode d’emploi

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur

Touchboards peerless CPA100WALLARM Mode d’emploi

Manuels Support et étagère populaires d'autres marques