Toto Link CP150 Manuel utilisateur

Manufacturer: ZIONCOM ELECTRONICS (SHENZHEN) LTD.

ADD: Room 702, Unit D, 4 Building Shenzhen Software Industry Base,

Xuefu Road, Nanshan District, Shenzhen, Guangdong, China.

Website: http://www.totolink.net

Information in this docutment is subject to change without prior notice.

V2.0 | 2008

User Guide

Wireless Outdoor CPE

Suitable for: CP150, CP300

Contents

1.1 Device Mounting 01

1.2 Network Connection 02

1.3 Port, Button, LED Indicators Description 03

FAQs 19

1. Hardware Installation

2. Typical Application

5.3 Repeater Mode

5.4 WISP Mode

5.2 Client Mode

3. Set Up PC

4. Conﬁgure the Device

5. Working Modes

5.1 AP Mode

0201

1. Hardware Installation

1.1 Device Mounting

Pole Mount

Wall Mount

1. Attach the groove part of the device to the pole.

2. Thread through the hole of CP300 and ties the

straps firmly on the pole.

1. Drive the nail into the wall and make sure the nail

position is exactly matching the device.

2. Hang the CP300 on the wall.

1.2 Network Connection

Note

1.Locate a suitable mounting site for your CPE. For choosing the best location, select an

elevated location where trees, buildings and large steel structures will not obstruct the

antenna signals and which offers maximum line-of-sight prop-agation with the users.

2.Adjust the direction of your CPE for a best signal. Place the straps through the slots on

the back of the CPE and then around the pole. Tighten the Straps.

3.Please make sure the two CPEs are placed face to face, otherwise the wireless signal

strength might be weak.

PoE Power Adaptor

DCP026

Switch

03 04

1.3 Port, Button, LED Indicators Description

Port and Button

LAN

Reset

Description

This port is used to access RJ45 cable to connect to PoE Power

Adapter, meanwhile realize data transmission.

With the CPE powered on, press and hold the button for about 10

seconds, the CPE will reboot to factory default settings.

LED Indicator

POWER

LAN

WLAN

Signal

Description

The POWER LED will light blue when properly connected to a power source.

This Ethernet LED will light solid blue when an active Ethernet connection

is made to the LAN port and flash when there is activity.

This WLAN LED flash blue when the wireless function working.

These LEDs display the signal strength.

RJ45 PORT

(PoE Supported) RESET

2. Typical Application

WISP

CP300

Switch

Computer

PoE Power Adapter

Cable

CP300

DCP026

0605

Choose “Use the following IP

address”, input the IP address in

the same network segment with

your router’s default IP address,

as below, then click “OK”.

3. Set Up PC

Double-click “Internet Protocol

Version 4 (TCP/IPv4)”

Right-click “My Network

Places”, click “Properties”

Right-click “Local Area

Connection”, click “Properties”

4. Conﬁgure the Device

Please set up the CPE following below steps.

Run the Web browser.

Type 192.168.1.1 in the Web browser address bar, then press Enter.

Input User Name and Password and click “Login”.

(By default, both are “admin” in lower case)

07 08

Select the proper Operation Mode as your requirement.

TOTOLINK CPE supports multiple Operation Modes to satisfy

diversified network requirements, including AP Mode, Client Mode,

Repeater Mode and WISP Mode. The following guide introduces

typical scenarios of each mode. Please choose the proper

Operation Mode according to your needs.

5.1 AP Mode

5.Working Modes

Scenario 1

Tablet

Router

Switch

Switch Switch

Server

PC PC PC

Smart phone

Access Point

Laptop

Campus network

09 10

Scenario 2

Scenario 3

Access Point

LAN: 192.168.7.2

WISP

LAN: 192.168.1.1

WAN: Dynamic IP

WISP

LAN: 192.168.1.1

WAN: PPPoE

WISP

LAN: 192.168.1.1

WAN: Static IP

Router

LAN: 192.168.7.1

AP Settings

Connect two office areas

1) Go to the CPE’s Operation Mode page.

2) Choose “AP Mode”, setup the CPE’s SSID,Channel and Key

(pass word), click Finishd.

Access Point

LAN: 192.168.1.1

Client

LAN: 192.168.1.2

PC IP Camera

Access Point

LAN: 192.168.1.1

Client

LAN: 192.168.1.2

Switch Switch

PC PC PC PC

Office NetworkOffice Network

11 12

3) After the settings, please connect the PoE Power Adapter LAN port

to upper level network device

5.2 Client Mode

Client Settings

Scenario 1

Connect two office areas

1）Go to CPE’s Operation Mode page.

2）Choose “Client ”, click “Wi-Fi Scan” to check all available wireless

networks around

3 ) Choose the SSID you need to connect. Enter correct Password,

click “Finished”.

Access Point

LAN: 192.168.1.1

Client

LAN: 192.168.1.2

PC IP Camera

Access Point

LAN: 192.168.1.1

Client

LAN: 192.168.1.2

Switch Switch

PC PC PC PC

Office NetworkOffice Network

5.3 Repeater Mode

1413

Repeater Settings

1）Go to CPE’s Operation Mode page.

2）Choose “Repeater”, click “Wi-Fi Scan” to check all available wireless

networks

Scenario 1

Scenario 2

Router

LAN: 192.168.7.1

Access Point

LAN: 192.168.7.2

SSID: abc

Repeater

LAN: 192.168.7.3

SSID: abc

Repeater

LAN: 192.168.7.4

SSID: abc

Smart Phone

Tablet PC

Laptop

Smart Phone

Tablet PC

Laptop

IP Camera

Repeater

LAN: 192.168.1.11

Access Point

LAN: 192.168.1.1

Repeater

LAN: 192.168.1.10

SSID: abc SSID: abc

4) Setup the expanded network SSID and password. Click “Finished”.

3）Select the SSID that you want to connect, enter correct key. Then

click “Next” to setup the expanded network parameters.

5.4 WISP Mode

15 16

WISP Settings

1）Go to CPE’s Operation Mode page.

2）Choose “WISP”, click “Wi-Fi Scan”, the device will check all available

ISP wireless networks around.

5) Now setup your PC’s LAN card IP address to “Obtain the IP address

automatically. Or you can access the Wi-Fi network through wireless

devices.

Scenario 1

WISP

AP Client Router

LAN: 192.168.1.1

WAN: PPPoE/Dynamic IP/

Static IP

Smart phone

Tablet PC

Laptop

3 ) Select the ISP Wi-Fi you need to connect. Enter correct Password,

Then click “Finished”.

4 ) Choose WAN Method:

Autres manuels pour CP150

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toto Link Point d'accès sans fil

Toto Link

Toto Link CP900 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur