Totem T-REX Manuel utilisateur
For more tips, please visit the link below:
https://totemmaker.net/blog/totem-mechanics-for-beginners/
STARTING TIPS
It is a good idea to
start every step in-
serting nuts into
beams (if the step
requires).
Use the back of the
screwdriver to push
in the nuts.
After entering the
fi rst slot, nuts tend
to tilt. Use your
thumb to push it
back straight, and
then again use the
screwdriver to in-
sert the nut all the
way in.
Push Nylon
Standoff with your
thumb while tight-
ening it with the
wrench.
Some of the nuts
are missing threads.
This is a manufac-
turing issue and we
are working on it. In
the mean time, we
add few extra nuts.
We apologize for
the inconvenience.
Use Beam/Bolt
ruler to determine
the length of beams
and bolts.
Inserting nuts (1) Inserting nuts (2) Faulty threads Tightening
standoff s
Ruler
PART LIST
3x Beam 90 mm 18x Beam 40 mm 4x Board Triangular 37x Bolt M3x6 1x Bolt M3x8 2x Bolt M3x10
4x Bolt M3x12 1x Bolt M3x16 1x Bolt M3x20 4x Bolt M3x25 4x 2-Hole 45 Simple Bracket 9x 2-Hole Simple Bracket
1x L-Twisted Bracket 1x L-Twisted Mirror Bracket 2x C-Bracket 2x 3-Hole 90 Bracket 3x Lock Nut M3 47x Nut M3 6x10
2x Nylon Spacer 4 mm 1x Nylon Spacer 8 mm 2x DC Motor Hub 2x DC Motor Bracket 1x Battery Case with Switch 1x DC Motor
1x Totem Screwdriver 1x Totem Wrench
1
2x Beam 40 mm 3x Bolt M3x6
6x Nut M3 6x10 1x Step 1 Assembly
1x 2-Hole Simple Bracket
2
1x Beam 40 mm 2x 2-Hole
Simple Bracket
3x Nut M3 6x10 1x Bolt M3x6
2x Beam 40 mm 3x Bolt M3x6
3x Nut M3 6x10 1x Step 3 Assembly
1x 2-Hole Simple Bracket
3
4
1x Beam 40 mm 2x 2-Hole
Simple Bracket
2x Nut M3 6x10 1x Bolt M3x6
5
2x Bolt M3x12 1x Bolt M3x16
1x Step 2 Assembly 1x Step 4 Assembly
6
2x DC Motor Bracket 2x Nut M3 6x10
2x Bolt M3x10 2x Bolt M3x25
1x DC Motor
7
1x Beam 90 mm 1x Beam 40 mm
2x Bolt M3x6 1x L-Twisted Bracket
4x Nut M3 6x10
1) Screw this
bolt fi rst.
2) Screw this
bolt secondly.
8
1x Beam 40 mm 2x Board Triangle
4x Bolt M3x6 1x Bolt M3x20
1x L-Twisted
Mirror Bracket
1x 2-Hole 45
Simple Bracket
1x Nylon Spacer 8 mm 1x Lock Nut M3
2x Nut M3 6x10 1x Step 7 Assembly
Do not over tighten
the Lock Nut. Let
the tail move freely.
Use wrench for
Lock Nut.
9
1x Bolt M3x6
Table des matières
Autres manuels Totem Jouet
