Totem BLACK SPIDER Manuel utilisateur
STARTING TIPS
It is a good idea to
start every step in-
serting nuts into
beams (if the step
requires).
Use the back of the
screwdriver to push
in the nuts.
After entering the
rst slot, nuts tend
to tilt. Use your
thumb to push it
back straight, and
then again use the
screwdriver to in-
sert the nut all the
way in.
Push Nylon
Stando with your
thumb while tight-
ening it with the
wrench.
Some of the
nuts are missing
threads. This is a
manufacturing is-
sue and we are
working on it. In the
mean time, we add
few extra nuts. We
apologize for the
inconvenience.
Use Beam/Bolt
ruler to determine
the length of beams
and bolts.
For more tips, please visit the link below:
https://totemmaker.net/blog/totem-mechanics-for-beginners/
Inserting nuts (1) Inserting nuts (2) Faulty threads Tightening
standos
Ruler
PART LIST
224x
M3x6 mm Bolt
226x
Nut M3 6x10
8x
M3x10 mm Bolt
80x
2-Hole Simple Bracket
8x
2-Hole 45 Simple Bracket
8x
Single Side Filler
40x
Lock Nut M3
92x
M3x8 mm Bolt
32x
Beam Plug
64x
Nut M3 6x6
6x
M3x25 mm Bolt
8x
M3-HEXH 12 mm Bolt
24x
Washer 9/0.8mm M3
2x
Upper Gear A
2x
Upper Gear B
8x
M3x45 mm Bolt
16x
2-Hole 45 Bracket
8x
Rocker Washer
6x
L-Twisted Bracket
6x
L-Twisted Mirror Bracket
16x
C-Bracket
6x
Bearing 8x16x5
4x
Lower Gear Hub
2x
Upper Gear Hub
2x
Motor-Plate 37 mm
4x
3-Hole Bracket
4x
Nylon Standoff M3x8 mm
16x
Double Side Filler
2x
Swan 90x45
4x
3-Hole 45 Bracket
16x
M3x12 mm Bolt
1x
Metal Nut M3
4x
Spider foot A
4x
Spider foot B
8x
Rocker
16x
Upper Arm Washer
16x
Washer 8/1 mm M3 Nylon
8x
M3x14 mm Bolt
8x
M3x16 mm Bolt
2x
Lower Gear A
2x
Lower Gear B
2x
Lower Gear C
2x
Lower Gear D
2x
Zip Tie 25 mm
3x18650 Li-ion pack
1x 1x
RoboBoard X4
2x
Motor Coupler 6 mm
2x
DC Motor 37 mm
2 cm 4 x
3 cm 4 x
4 cm 4 x
5 cm 24 x
6 cm 18 x
7 cm 6 x
9 cm 16 x
10 cm 2 x
11 cm 2 x
13 cm 2 x
17 cm 4 x
3 cm/6H 8 x
3.5 cm/7H 12 x
4.5 cm/9H 8 x
7.5 cm/15H 8 x
9.5 cm/19H 8 x
BEAMS:
STRIP BRACKETS:
PART LIST
2x
2x
2x
4x
2x
13 cm
6 cm17 cm
11 cm
4 cm
9 cm 9 cm
6 cm
5 cm 5 cm
10 cm
3 cm
6 cm
2 cm
= 15x40 cm Beams Total
Cutting 40 cm Beams
9 cm
17 cm
5 cm 5 cm9 cm
9 cm 6 cm
6 cm
7 cm
9 cm 9 cm 5 cm 5 cm
5 cm 5 cm 5 cm 5 cm 5 cm 5 cm
7 cm
4 cm 4 cm 4 cm 3 cm 3 cm 2 cm 14 cm leftover
2x
1x
1A
12x
2-Hole Simple Bracket
8x
M3x8 mm Bolt
8x
Nut M3 6x6
AB
4x 4x
8x
M3x10 mm Bolt
40x
2-Hole Simple
Bracket
8x
2-Hole 45 Simple
Bracket
8x
Single Side Filler
8x
Lock Nut M3
48x
M3x8 mm Bolt
16x
Beam Plug
48x
Nut M3 6x6
8x
M3x16 mm Bolt
4x
Spider Foot A
4x
Spider Foot B
PART 1
16x
8x
8x
8x
4x
4x
5 cm Beam
9 cm Beam
9 cm Beam
4.5 cm/9 Holes Strip Bracket
7.5 cm/15 Holes Strip Bracket
7.5 cm/15 Holes Strip
Bracket
Repeat this step 4 times.
4x
A
2
8x
M3x8 mm Bolt
8x
Nut M3 6x6
4x
Single Side Filler
4x
2-Hole 45 Simple Bracket
Repeat this step 4 times.
4x
4x
4x
5 cm Beam
4.5 cm/9 Holes Strip
Bracket
3A
8x
2-Hole Simple Bracket
8x
M3x8 mm Bolt
8x
Beam Plug
8x
Nut M3 6x6
Repeat this step 4 times.
4x
4x
5 cm Beam
4A
4x
Lock Nut M3
4x
M3x16 mm Bolt
Repeat this step 4 times.
4x
5A
Tip for tightening lock nuts:
Here a bolt and a lock nut is used as a hub or bearing
in joints between the spider leg parts. They should
not be tightened too much, since they must rotate
easily. But they should not be wobbly either. Find the
tightening that you feel is good.
Alternatively use a
socket for 5.5 mm
HEX heads to hold
the lock nuts.
Repeat this step 4 times.
4x
Table des matières
Autres manuels Totem Jouet
