Toshiba D-R350SB Manuel utilisateur

DVD VIDEO RECORDER

SERVICE MANUAL

May, 2005

FILE NO. 810-200548

D-R350SB

DIGITAL VIDEO

PREPARATION OF SERVICING

Pickup Head consists of a laser diode that is very susceptible to external static electricity.

Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement,

its life might be shortened. When replacing, use a conductive mat, soldering iron with ground wire, etc. to

protect the laser diode from damage by static electricity.

And also, the SI and IC are same as above.

Ground conductive

wrist strap for body.

Soldering iron

with ground wire

or ceramic type

Conductive mat The ground resistance

between the ground line

and the ground is less than 10

LASER BEAM CAUTION LABEL

When the power supply is being turned on, you may not remove this laser cautions label. If it removes, radiation of a laser

may be received.

·Manufactured under license from Dolby Laboratories. “Dolby” and the double D symbol are trademarks of Dolby

Laboratories.

·“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

·Manufactured under license from QSound Labs, Inc. U.S. patent Nos. 5,105,462, 5,208,860 and 5,440,638 and various

foreign counterpart. Copyright QSound Labs, Inc. 1998 2002. QXpanderTM is a trademark of QSound Labs, Inc. All

rights reserved.

·VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system

is manufactured under license from Gemstar Development Corporation.

SECTION 2

PART REPLACEMENT AND ADJUSTMENT PROCEDURES

SECTION 3

SERVICING DIAGRAMS

1. CIRCUIT SYMBOLS AND

SUPPLEMENTARY EXPLANATION

1-1. Precau ions for Par Replacemen

1-2. Solid Resis or Indica ion

1-3. Capaci ance Indica ion

1-4. Induc or Indica ion

1-5. Waveform and Vol age Measuremen

1-6. O hers

2. PRINTED WIRING BOARD AND

SCHEMATIC DIAGRAM

3. BLOCK DIAGRAMS

3-1. Overall Block Diagram

4. CIRCUIT DIAGRAMS

4-1. Power Supply Circui Diagram

4-2. Fron Circui Diagram

4-2-1. Fron Jack Circui Diagram

4-2-2. Fron (L) Circui Diagram

4-2-3. Fron (R) Circui Diagram

4-2-4. Fron LED Circui Diagram

4-3. Digi al Circui Diagram

4-4. Mo her Circui Diagram

4-4-1. Tuner In erface Circui Diagram [SH.1]

4-4-2. Audio Circui Diagram [SH.2]

4-4-3. Timer Circui Diagram [SH.3]

4-4-4. Video Circui Diagram [SH.4]

4-4-5. MSP Circui Diagram [SH.5]

5. PC BOARDS

5-1. Power Supply PC Board

5-2. Fron Jack PC Board

5-3. Fron (L) PC Board

5-4. Fron (R) PC Board

5-5. Fron LED PC Board

5-6. Digi al PC Board

5-7. Mo her PC Board

CONTENTS

SECTION 1

GENERAL DESCRIPTIONS

1. OPERATING INSTRUCTIONS

1. REPLACEMENT OF MECHANICAL PARTS

1-1. Cabine Replacemen

1-1-1. Top Cover

1-1-2. Fron Panel

1-1-3. RAM Drive

1-1-4. Rear Panel

1-1-5. Fan

1-2. PC Board Replacemen

1-2-1. Digi al PC Board

1-2-2. Mo her PC Board

1-2-3. Power PC Board

1-2-4. Fron (R), Fron (L), Fron (LED),

Fron Jack PC Boards

2. WIRING CONNECTION DIAGRAM

2. LOCATION OF MAIN PARTS

2-1. Loca ion of Main Par s

2-2. Loca ion of PC Boards

SECTION 4

PARTS LIST

SAFETY PRECAUTION

NOTICE

ABBREVIATIONS

1. EXPLODED VIEWS

1-1. Packing Assembly

1-2. Chassis Assembly

2. PARTS LIST

SECTION 1

GENERAL DESCRIPTIONS

1. OPERATING INSTRUCTIONS

Please refer to the owner's manual about the contents.

SECTION 1

GENERAL DESCRIPTIONS

2. LOCATION OF MAIN PARTS

2-1. Location of Main Parts

Fig. 1-2-1

2-2. Location of PC Boards

Fig. 1-2-2

ZG45 FAN

RAM1 RAM DRIVE

EU02 Power PC board

EU05 Mother PC board

EU01 Digital PC board

EU03A Front (R) PC board

EU55 Front Jack PC board

EU03B Front (L)

PC board

EU56 Front (LED)

PC board

1-1. Cabinet Replacement

1-1-1. Top Cover

1. Remove seven screws (1), then remove the top cover (2).

Fig. 2-1-1

SECTION 2

PART REPLACEMENT AND

ADJUSTMENT PROCEDURES

Screws (1)

Top cover (2)

SECTION 2

PART REPLACEMENT AND

ADJUSTMENT PROCEDURES

CAUTIONS BEFORE STARTING PART REPLACEMENT

Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to ground as required.

any screws are used inside the unit. To prevent the screws from missing or dropping, etc. always use a magnetized

screwdriver in servicing. Several kinds of screws are used and some of them need special cautions. That is, take care of

the tapping screws securing molded parts and fine pitch screws used to secure metal parts. If they are used improperly,

the screw holes will be easily damaged and the parts can not be fixed.

1. REPLACEMENT OF MECHANICAL PARTS

1-1-2. Front Panel

1. Remove the top cover. (Refer to item 1-1-1.)

2. Remove the Digital PC board. (Refer to item 1-2-1.)

3. Disconnect three connectors (1).

4. Remove t o scre s (2) and four cla s, then remove the front panel (3).

Fig. 2-1-2

1-1-3. RAM Drive

1. Remove the front panel. (Refer to item 1-1-2.)

2. Peel off the tape (1).

3. Disconnect the flexible cable (2) and connector (3).

4. Remove three scre s (4) and three scre s (5), then remove the RAM drive (6).

5. Remove the shield cover (7).

Note:

• After replacing, attach the tape (1) to its original position.

Fig. 2-1-3

Connector (1)

Screws (2)

Front panel (3)

Claw

Claws

Flexible

cable (2)

Connector (3)

Tape (1)

Screws (4)

Screws (5)

RAM drive (6)

Shield cover (7)

1-1-4. Rear Panel

1. Remove the top cover. (Refer to item 1-1-1.)

2. Peel of the tape (1).

3. Remove two screws (2) and seven screws (3).

4. Remove two claws, then remove the rear panel (4).

5. Remove two screws (5), then remove the fan (6).

Note:

After replacing, attach the tape (1) to its original position.

Fig. 2-1-4

1-1-5. Fan

1. Remove the top cover. (Refer to item 1-1-1.)

2. Peel off the tape (1).

3. Disconnect the connector (2).

4. Remove two screws (3), then remove the fan (4).

Note:

After replacing, attach the tape (1) to its original position.

Screws (2)

Screws (3)

Screws (5)

Fan (6)

Tape (1)

Rear pane (4)

C aw

Screws (3)

Connector (2)

Fan (4)

Tape (1)

Hexagona

nuts

Fig. 2-1-5

1-2. PC Board Replacement

1-2-1. Digital PC Board

1. Remove the top cover. (Refer to item 1-1-1.)

2. Disconnect the flexible cable (1).

3. Remove four screws (2), then remove the Digital C board (3).

Note:

• The Digital C board (3) is connected to the Mother C board (4) by three connectors (5). Take notice when removing.

Fig. 2-1-6

Screws (2)

Digita PC

board (3)

F exib e

cab e (1)

F exib e

cab e (1)

Connector

C aw

Connector (5) Connectors (5)

Mother PC board (4)

Remove the connector c aw

in the direction indicated

by the arrows to re ease the

f exib e cab e.

1-2-2. Mother PC Board

1. Remove the rear panel. (Refer to item 1-1-4.)

2. Remove the Digital PC board. (Refer to item 1-2-1.)

3. Disconnect three connectors (1).

4. Remove five scre s (2) .

5. Pull out the Mother PC board (3) to ard the rear side (indicated by the arro ).

Fig. 2-1-7

Screws (2)

Mother PC

board (3)

Connectors (1) Connector (1)

Table des matières

Autres manuels Toshiba DVR

Toshiba

Toshiba RD-XS32SB Manuel utilisateur

Toshiba

Toshiba D-RW2SU Manuel utilisateur

Toshiba

Toshiba D-VR7KC2 Manuel utilisateur

Toshiba

Toshiba RD-XS34S Manuel utilisateur

Toshiba

Toshiba D-R2S Manuel utilisateur

Toshiba

Toshiba D-RW2 - DVD Recorder With TV Tuner Manuel utilisateur

Toshiba

Toshiba DVR Manuel utilisateur

Toshiba

Toshiba RD-XS34SB Manuel utilisateur

Toshiba

Toshiba D-R420KU Manuel utilisateur

Toshiba

Toshiba D-R560KU Manuel utilisateur

Toshiba

Toshiba RD-85DTSB Manuel utilisateur

Toshiba

Toshiba RD-85DTSB Manuel utilisateur

Toshiba

Toshiba D-RW2SC Manuel utilisateur

Toshiba

Toshiba D-KVR20KU Manuel utilisateur

Toshiba

Toshiba D-R550KU Manuel utilisateur

Toshiba

Toshiba Surveillix XVSv16-240-X Manuel utilisateur

Toshiba

Toshiba RD-XS30SB Manuel utilisateur

Toshiba

Toshiba surveillix KV-PCDVR Manuel utilisateur

Toshiba

Toshiba DVSe Manuel utilisateur

Toshiba

Toshiba RD-XS27KE Manuel utilisateur

Toshiba

Toshiba RD-97DTKB Manuel utilisateur

Toshiba

Toshiba RD-XS54SU Manuel utilisateur

Toshiba

Toshiba Surveillix XVR16-120-X Manuel utilisateur

Toshiba

Toshiba RD-85DTSB Manuel utilisateur

Manuels DVR populaires d'autres marques

FLIR

FLIR M3100E Series Manuel utilisateur

VTRACKPRO

VTRACKPRO FPRO300 Manuel utilisateur

Swann

Swann NVR-7085 models Manuel utilisateur

XtendLan

XtendLan DVR-1670C Manuel utilisateur

urmet domus

urmet domus 1093/004AHD Manuel utilisateur

Holux

Holux M1 Manuel utilisateur

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuel utilisateur

Whistler

Whistler D16VRS Manuel utilisateur

Defender Security

Defender Security 82-20235 Manuel utilisateur

MISUMI

MISUMI MP-WF100M Manuel utilisateur

Speco

Speco D8HU Manuel utilisateur

UST

UST DDR-E04AA Instructions d'utilisation

Consolidated

Consolidated Digital Video Recorder Manuel utilisateur

Mace

Mace DVR0404RW Guide de démarrage rapide

RCA

RCA RTD315W Manuel utilisateur

FSM

FSM Colibri Grande PRO Manuel utilisateur

Hauppauge

Hauppauge HD PVR 2 Manuel utilisateur

Identivision

Identivision ICR-PH161i PIONEER Manuel utilisateur