Toro 1800 Power Curve Manuel utilisateur

1800 POWER CURVE

1Service Instruction TSN0001a

1. Stand the snowthrower on its wheels and position

the upper handle. Inspect the wiring for any signs of

damage. If any damage is found, do not assemble.

Contact an Authorized Service Dealer (Fig. 001 and

Fig. 002).

2. Insert the right side of the upper tubing over the

lower right side tubing (Fig. 003).

3. Insert the left side of the upper tubing into the lower

left side tubing (Fig. 004).

Fig. 001 PICT-1418

Fig. 002 PICT-1419

Fig. 004 PICT-1424

Fig. 003 PICT-1422

Upper Handle & Chute Crank Installation

1800 Power Curve Set-up / Assembly

1800 POWER CURVE

2 Service Instruction TSN0001a

4. Squeeze the upper tubes together and wiggle the

upper tubes down until the mounting holes in the

upper and lower tubing line up:

Left hand (Fig. 005):

5. Place the mounting plate over the tubes and align

the mounting plate holes with the upper and lower

tubing holes (Fig. 007).

Right hand (Fig. 006):

6. Insert the end of the chute crank rod through the

hole in the shroud (Fig. 008).

Fig. 005 PICT-1437

Fig. 006 PICT-1438

Fig. 008 PICT-1443

Fig. 007 PICT-1441

1800 POWER CURVE

3Service Instruction TSN0001a

7. Turnthechutecrankrodlightlyuntiltheattened

end drops into the slot in the chute crank gear (Fig.

009).

9. Ensure the mounting plate holes are aligned with the

upper and lower tubing holes (Fig. 011 - LH hole).

8. Firmly push the chute crank rod into the chute crank

gear until it snaps into place (Fig. 010).

10. Insert the LH bolt though the holes (Fig. 012).

Note: Insert the screws from the outside of the

mounting plate. Be careful not to damage the

internal wiring when you insert the screws.

If the wiring blocks the hole, use a blunt

end punch to route the wiring away from the

aligned holes.

Fig. 009 PICT-1444

Fig. 010 PICT-1447a

Fig. 012 PICT-1451

Fig. 011 PICT-1449

1800 POWER CURVE

4 Service Instruction TSN0001a

11. Install and tighten the nut securing the LH side (Fig.

013).

12. If the wiring blocks the hole on the RH handle, use

a blunt end punch to route the wiring away from the

aligned holes (Fig. 014 and Fig. 015).

Fig. 013 PICT-1456

Fig. 014 PICT-1459

Fig. 015 PICT-1463

1800 POWER CURVE

5Service Instruction TSN0001a

13. Insert the RH bolt through the holes and force the

punch out (Fig. 016 and Fig. 017).

14. Install and tighten the nut securing the RH side (Fig.

018).

Fig. 016 PICT-1465

Fig. 017 PICT-1466

Fig. 018 PICT-1468a

1800 POWER CURVE

6 Service Instruction TSN0001a

Discharge Chute Installation

1. Partially insert a carriage bolt through the lower

chute (Fig. 019).

3. Positionthedeectorchuteontothelowerchuteand

align the mounting holes (Fig. 021).

2. Insert a rubber washer onto the carriage bolt (Fig.

020).

4. Insertametalatwasherontothecarriagebolt(Fig.

022).

Fig. 019 PICT-1471

Fig. 020 PICT-1474

Fig. 022 PICT-1478

Fig. 021 PICT-1476

1800 POWER CURVE

7Service Instruction TSN0001a

5. Loosely install a lock nut to secure one side of the

deectorchuteassembly(Fig.023).

7. Insert the carriage bolt through the lower chute,

rubberwasheranddeectorchute(Fig.025).

6. Positionarubberwasherbetweenthedeector

chute and the lower chute while maintaining the hole

alignment (Fig. 024).

8. Installthemetalatwasherontothecarriagebolt

(Fig. 026).

Fig. 023 PICT-1479

Fig. 024 PICT-1485a

Fig. 026 PICT-1488

Fig. 025 PICT-1484

1800 POWER CURVE

8 Service Instruction TSN0001a

9. Install and tighten the locknut (Fig. 027).

11. Cyclethedeectorchutetoensureitmoveswitha

smallamountofresistance.Tootight,thedeector

chute will not move; too loose, the force of the snow

beingdischargedwillipthedeectorchuteup.

10. Tighten the locknut on the opposite side of the

deectorchuteassembly(Fig.028).

Fig. 027 PICT-1490

Fig. 028 PICT-1492

Autres manuels pour 1800 Power Curve

Table des matières

Autres manuels Toro Souffleuse à neige

Toro

Toro Power Shovel 38361 Manuel utilisateur

Toro

Toro 38650 Manuel utilisateur

Toro

Toro 38078 Manuel utilisateur

Toro

Toro Power Clear 518 Manuel utilisateur

Toro

Toro Power Max Heavy Duty 826 OXE Manuel utilisateur

Toro

Toro 38025 - 18" Power Curve Electric Snow... Mode d’emploi

Toro

Toro Power TRX 1428 OHXE Manuel utilisateur

Toro

Toro Power Max Heavy Duty 1030 Manuel utilisateur

Toro

Toro Power Clear 621 ZR Manuel utilisateur

Toro

Toro CCR POWERLITE 38170 Manuel utilisateur

Toro

Toro Powerlite 38274 Manuel utilisateur

Toro

Toro 38588 Manuel utilisateur

Toro

Toro Power Max Series Manuel utilisateur

Toro

Toro 38720 Manuel utilisateur

Toro

Toro 79365 Manuel utilisateur

Toro

Toro Snow Commander 38600 Manuel utilisateur

Toro

Toro Power Max 828LXE Manuel utilisateur

Toro

Toro Snow Commander 38602 Manuel utilisateur

Toro

Toro CCR 1000 38400 Manuel utilisateur

Toro

Toro PowerMax 38614 Manuel utilisateur

Toro

Toro Power Clear 721 Manuel utilisateur

Toro

Toro 38710 Manuel utilisateur

Toro

Toro Power Max 1028LE Manuel utilisateur

Toro

Toro 38657C Manuel utilisateur

Manuels Souffleuse à neige populaires d'autres marques

Murray

Murray 624504X4A Manuel utilisateur

Blizzard

Blizzard POWER PLOW 8100PP Manuel utilisateur

Craftsman

Craftsman 486.24837 Manuel utilisateur

Yard-Man

Yard-Man E2B5 Manuel utilisateur

ST ST 526 A Manuel utilisateur

MTD

MTD 3AA Manuel utilisateur

Ryobi

Ryobi RYAC800 Manuel utilisateur

Poulan Pro

Poulan Pro 416829 Manuel utilisateur

Poulan Pro

Poulan Pro 437986 Manuel utilisateur

MTD

MTD 319-180-00 Manuel utilisateur

Brute

Brute 1695565 Manuel utilisateur

Egholm

Egholm City Ranger 2250 Manuel utilisateur

Poulan Pro

Poulan Pro 420915 Manuel utilisateur

GreenWorks

GreenWorks SNF402 Manuel utilisateur

LOFTNESS

LOFTNESS 601D1 Manuel utilisateur

LOFTNESS

LOFTNESS 1082I Manuel utilisateur

LOFTNESS

LOFTNESS 481EL Manuel utilisateur

White Outdoor

White Outdoor 769-01923A Manuel utilisateur