ToolPRO 630873 Manuel utilisateur

1100W

WET AND DRY VACUUM CLEANER

PLU: 630873

PRODUCT SAFETY

GENERAL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions.

Failure to follow all instructions listed

below may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

- This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the appliance.

- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualiﬁed persons in order to avoid a hazard.

- The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.

Warning

Read the operator’s manual

Double insulation

RCM marking

ABN: Australian Business Number. By this number, business information such as entity

type, status, business location etc. can be found at website http://abr.business.gov.au.

ABN of Positec Australia Pty Limited is 23 113 230 050.

SYMBOLS

WET AND DRY VACUUM CLEANER

IN THE BOX

Carry Handle

Flexible Hose Outlet - Blower

Side Locking Handle (X2)

Tank

On Board Storage / Holders

Base

Castor Wheels (X4)

On/Off Switch

Appliance Head

Flexible Hose Outlet - Suction

Extension Tubes (X3)

Crevice Tool

Floor Tool

Foam Filter

HEPA Filter

Flexible Hose

Power Cord

Filter Basket

Floating Safety Valve

ACCESSORIES

Suction hose (1.5m) 1

HEPA ﬁlter 1

Foam ﬁlter 1

Castors 4

Floor tool 1

Crevice tool 1

Extension tubes 3

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction book carefully.

Intended Use

This product is suitable for cleaning dirt, debris and liquids from garages, workshops, courtyards,

patios and garden environment, as well as dust extraction function using the AC outlet for electric

power tools.

Assembly

WARNING: To prevent serious injury from accidental operation, turn the power switch of the

vacuum off and unplug the appliance from its electrical outlet before performing any

procedure in this section. Before you connect the vacuum to a mains supply, make sure

that the data on the rating / technical label is identical to the mains data.

The Wet and Dry Vacuum should only be connected to a mains power supply socket; an RCD

(Residual Current Device) is recommended.

The Wet and Dry Vacuum requires some assembly prior to use. This includes assembly of the wheels,

and dependent upon the use of the product, the ﬂexible hose, tubes, ﬁlters, and accessories. The

following detail covers the assembly required for each function of the Wet and Dry Vacuum.

Assembly of the wheels

1. Remove the appliance head from the tank by unlocking the side locking handles pulling them

outwards, then upwards (Fig A). Then turn the tank upside down.

2. Fit the 4 x castor wheels by inserting the mounting pin on the castor wheel into the designated

mounting hole on the underside of the base. Firmly push the castor wheels into the mounting

holes (Fig B).

NOTE: Take care not to damage the castor wheel. They do not need to be forced into position.

3. When all 4 castor wheels are ﬁtted, turn the product the right way up, and re-attach

the appliance head ensuring you align the notches on the ridge of the tank lip with the side locking

handles, and secure the 2 side locking handles in position (Fig C).

WET AND DRY VACUUM CLEANER

Assembly for Dry Vacuuming – HEPA Filter

WARNING: Never use the vacuum without a filter. Check that the filter is securely fitted at

all times.

The Wet and Dry Vacuum is ﬁtted with the HEPA ﬁlter used for dry vacuuming upon purchase.

To continue assembly for dry vacuuming, continue to the ‘Fitting the ﬂexible hose’ section.

Assembly for Wet Vacuuming – Foam Filter

WARNING: Never use the vacuum without a filter. Check that the filter is securely fitted at

all times.

1. Remove the appliance head from the tank by unlocking the 2 x side locking handles pulling them

outwards, then upwards (Fig A). Place the appliance head upside down onto a ﬂat surface, or on

its side.

2. Remove the HEPA ﬁlter (installed upon purchase) by pulling it away from the appliance head (Fig D)

3. Slip the foam ﬁlter over the ﬁlter basket (Fig E). Ensure the foam ﬁlter covers the full ﬁlter basket

(Fig F).

NOTE: The foam filter is only suitable for WET vacuuming.

IMPORTANT: Regularly clean the foam ﬁlter and allow it to dry before resuming vacuuming.

IMPORTANT: DO NOT use the HEPA ﬁlter for wet vacuuming (the HEPA ﬁlter is pre-installed upon

purchase).

IMPORTANT: The Wet and Dry Vacuum should only be connected to a mains power supply socket;

an RCD (Residual Current Device) is recommended.

4. Re-assemble the appliance head back onto the tank, and secure the 2 x side locking handles.

NOTE: Always unplug the appliance after use and before cleaning or changing the filters or

accessories.

Fitting the Flexible Hose

Connect the ﬂexible hose to the ﬂexible hose outlet depending on the application required:

1. Vacuuming

Connect the ﬂexible hose to the ﬂexible hose outlet – suction by inserting into the outlet and aligning

the arrow and locking pin on the end of the ﬂexible hose, with the arrow and ridge on the top of the

ﬂexible hose outlet – suction. This should ensure the locking pin on the ﬂexible hose aligns with the

ridge in the ﬂexible hose outlet – suction (Fig G).

WET AND DRY VACUUM CLEANER

Fitting the extension tubes and tools

1. To ﬁt an extension tube to the end of the ﬂexible hose, apply the larger opening end of an extension

tube over the end of the ﬂexible hose (Fig I).

2. To add an additional (2 or 3) ﬂexible tube/s, apply the larger opening end of the extension tube/s

over the ﬁrst extension tube until secure (Fig J).

3. For vacuuming, either the ﬂoor tool, or crevice tool can be added to the end of the last extension

tube by simply pushing it onto the extensions tube (Fig K/L).

2. Blowing

Connect the ﬂexible hose to the ﬂexible hose outlet – blowing by inserting into the outlet and aligning

the arrow and locking pin on the end of the ﬂexible hose, with the ridge on the top of the ﬂexible hose

outlet – blowing. This should ensure the locking pin on the ﬂexible hose aligns with the ridge in the

ﬂexible hose outlet – blowing (Fig H).

Operation

On/Off switch (Fig M):

Switch Position 0: OFF (All operations shut off)

Switch Position I: For normal vacuuming operation (wet or dry)

WET AND DRY VACUUM CLEANER

Dry Vacuuming

WARNING: Users must strictly observe all warnings and information contained in section

‘General safety warnings’ and in section ‘Operating Instructions’ before operating this appliance.

WARNING: DO NOT use the foam ﬁlter for dry vacuuming applications.

IMPORTANT: The Wet and Dry Vacuum should only be connected to a mains power supply socket; an

RCD (Residual Current Device) is recommended.

1. Ensure the tank is completely dry and free from dust and dirt.

2. Only use the HEPA ﬁlter for dry vacuuming applications (Fig N). Ensure you have already ﬁtted

the ﬂexible hose, extension tubes, and if required, the ﬂoor tool or crevice tool for dry vacuuming

applications.

IMPORTANT: Ensure the HEPA ﬁlter is securely ﬁtted before starting the tool.

3. Plug the power cord into the mains power outlet and turn on.

4. To commence vacuum mode operation, press the “I” on the ON/OFF switch (Fig O).

5. To turn off vacuum mode, press the “O” on the ON/OFF switch (Fig P).

* Dust bag can also be used for dry vacuuming and can be purchased separately as an accessory.

WARNING: Check the HEPA ﬁlter regularly for any blockages which may reduce the suction and

cause motor overheating. If the vacuum noise changes, immediately switch off the appliance by

pressing on the “O” on the ON/OFF switch and check the HEPA ﬁlter. Clean the HEPA ﬁlter and empty

the tank if required.

WARNING: Check the tank regularly and empty the waste collected when it is about 2/3 full.

Wet Vacuuming

WARNING: Users must strictly observe all warnings and information contained in section

‘General safety warnings’ and in section ‘Operating Instructions’ before operating this appliance.

WARNING: DO NOT use the HEPA ﬁlter for wet vacuuming applications.

IMPORTANT: The Wet and Dry Vacuum should only be connected to a mains power supply socket; an

RCD (Residual Current Device) is recommended.

1. Ensure the tank is completely dry and free from dust and dirt.

2. Only use the foam ﬁlter for wet vacuuming applications (Fig Q). Ensure you have already ﬁtted

the ﬂexible hose, extension tubes, and if required, the ﬂoor tool or crevice tool for wet vacuuming

applications.

IMPORTANT: Ensure the foam ﬁlter is securely ﬁtted before starting the tool.

3. Plug the power cord into the mains power outlet and turn on.

4. To commence vacuum mode operation, press the “I” on the ON/OFF switch (Fig O).

5. To turn off vacuum mode, press the “O” on the ON/OFF switch (Fig P).

6. When wet vacuuming, the ﬂoating safety valve closes when the maximum tank level is reached. In

doing so, the suction noise of the vacuum will change and become louder. When this happens, you

must switch off the vacuum and empty the tank.

WARNING: Check the tank regularly and empty the waste collected when it is about 2/3 full.

WARNING: The Wet and Dry Vacuum is not suitable for the vacuuming of combustible liquids.

Refer to section ‘Operating Instructions’ before operating this appliance.

IMPORTANT: Be aware that a full tank can be very heavy. In this event, please empty the waste liquid

in the tank.

7. To empty the tank, ﬁrstly ensure you are in an area where you plan to disperse the waste water.

Table des matières

Autres manuels ToolPRO Aspirateur

ToolPRO

ToolPRO 35L Manuel utilisateur

ToolPRO

ToolPRO 603752 Manuel utilisateur

Manuels Aspirateur populaires d'autres marques

Bissell

Bissell LittleGreen Proheat 1425 Series Manuel utilisateur

Panasonic

Panasonic MC-YL637S147-AE Manuel utilisateur

NEFF

NEFF N17XH10 0 Series Manuel utilisateur

LG A9 Series Manuel utilisateur

Oreck

Oreck Cordless Captura BK51700 Series Manuel utilisateur

Kogan

Kogan KAVACROBVWA Manuel utilisateur

Kränzle

Kränzle VENTOS 50 ID Guide de l'utilisateur

EVVO

EVVO Ai35 Manuel utilisateur

DeWalt

DeWalt DWH200D Manuel utilisateur

Pontec

Pontec Pondomatic Vacuum Cleaner Manuel utilisateur

Cleanmaxx

Cleanmaxx PC-P007E Manuel utilisateur

Exido

Exido 240-114 Manuel utilisateur

RIDGID

RIDGID WD1685AU0 Manuel utilisateur

Ezviz

Ezviz RE4P Manuel utilisateur

STG global

STG global TANVAC HDV3000 Manuel utilisateur

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuel utilisateur

Factory

Factory M3340 Manuel utilisateur

Shop-Vac

Shop-Vac VN92 SERIES Manuel utilisateur