Tong-Da 2503W Manuel utilisateur
2503W Image Projection MANUAL
Thank you for having chosen our company’s products. For your own safety, please read this user manual
carefully before installing the device.
SAFETY INTRODUCTION
If the device has been exposed to temperature changes due to environmental changes, do not
switch it on immediately. The arising condensation could damage the device. Leave the device
switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed. A
qualified person must carry out the electric connection.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power cord by plug. Never pull out the plug by tugging the power cord.
During initial start-up, some smoke or smell may arise. This is normal and should decrease
gradually.
CAUTION:
1. Be very careful during installation. Since you will be working with a dangerous voltage you
can suffer a life-threatening electric shock when touching live wires.
2. Never touch the device during operation, because the housing heats up.
3. Never look directly into the light source, as sensitive persons may suffer an epileptic shock.
4. Please be aware that damages caused by manual modifications to the device are not subject
to warranty. Keep away from children and non-professionals.
GENERAL GUIDELINES
This device is a lighting effect for professional use on stages, in discotheques, theatres, etc. This
fixture is only allowed to be operated with and alternating current of max.
240VAC/50Hz(125VAC/60Hz) and was designed for indoor use only.
Lighting effects are not designed for permanent operation. Consistent operation breaks will
ensure that the device will serve you for a long time without defects. Do not shake the device.
Avoid brute force when installing or operating the device.
When choosing the installation spot, please make sure that the device is not exposed to extreme
heat, moisture or dust. The minimum distance between light-output from the projector and the
illuminated surface must be more than 0.5 meter.
Always fix the fixture with an appropriate safety cable.
Make sure never to install the device in a place that exceeds the ambient temperature Ta(see
technical specifications at the end of this user manual).
Operate the device only after having familiarized with its functions. Do not permit operation by
person not qualified for operating the device. Most damages are the result of unprofessional
operation.
Please use the original packaging if the device is to be transported.
For safety reasons, please be aware that all modifications on the device are forbidden.
Furthermore, any other operation may lead to short-circuit, burns, electric shock, lamp explosion,
crash, etc. If this device will be operated in any way different to the one described in this manual,
the product may suffer damages and the guarantee becomes void.
INSTALLATION INSTRUCTIONS
a) Installing or replacing the lamps
Before replacing the lamps let the lamps cool down, because during operation, the lamps can
reach temperatures of up to 700℃.
During the installation of halogen lamps do not touch the glass bulbs bare handed. Always use a
cloth to handle the lamps during insertion and removal.
Do not install lamps with a higher wattage. They generate higher temperatures than for which the
device was designed for. For the installation, you need ELC 24v/250w Lamp.
Procedure:
1) Unscrew the screw
2) Gently open the lid
3) Remove the old lamp from the socket and insert a new lamp
4) Carefully replace the lid
5) Fix the screw
CAUTION: Do not operate this device with open cover!
b) Replacing the fuse
If the lamps burn out, chances are the fuse on the rear panel might too. Only replace the fuse
with a fuse of the same type and rating (see technical specifications at the end of this user
manual). For the installation, you need one 3A/250VAC (3A/125VAC) fuse.
Procedure:
1) Unscrew the fuse holder with an appropriate screwdriver
2) Remove the old fuse and replace it by the new one
3) Replace the fuse holder in the housing and fasten it with the screwdriver
CAUTION: Only replace the fuse with the device unplugged from the mains!
c) Mounting the device
The installation of the effect has to be built and constructed in a way that it can hold 10 times the
weight for1hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate
safety cable.
Never stand directly below the device when mounting, removing the fixture.
Procedure:
The projector should be installed outside areas where persons may reach it, walk by or be
seated.
Overhead mounting requires extensive experience, including amongst others calculating working
load limits, installation material being used, and periodic safety inspection of all installation
material and the device. If you lack these qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
Before mounting make sure that the installation area can hold a minimum point load of 10 times
the device s weight.
Adjust the desired inclination angle via the mounting bracket and fix the bracket screws tightly.
Connect the fixture to the mains with the power plug. In general, lighting effects should not be
connected to dimming packs.
CAUTION: When installing the device, make sure there is no highly inflammable
material within a distance of min. 0.5m!
CLEANING AND MAINTENANCE
The following points have to be considered during the inspection:
1) All screws for installing the devices or parts of the device have to be tightly connected and
must not be corroded.
2) There must not be any deformations on the housing, color lenses, fixations and installation
spots (ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4) The electric power supply cables must not show any damage, material fatigue or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use
alcohol or solvents.
CAUTION: Disconnect from mains before starting maintenance operation!
TECHNICAL SPECIFICATIONS
Power supply: max. 220V AC/60Hz
Power consumption: max.280w
Fuse: F10A, 250V AC
Lamps: ELC-C 24V/ 250W
Maximum ambient temperature Ta: 45℃
Maximum housing temperature Tb: 130℃
Tong-Da Industry Co., Ltd
Company web Site : http://www.ur.url.tw/ E-mail:japantaiwan@hotmail.com
Mobile Phone : + 886-0913-933255 TEL: + 886-6-293-4039 FAX : + 886-6-295-8668
Table des matières
Autres manuels Tong-Da Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
