TomTom PRO 2020 Manuel utilisateur
TomTom PRO 2020
Installation Guide
2
Contents
What’s in the box 3
Safety first 4
Important safety notices and warnings.............................................................................................4
Connection overview 6
Choosing the correct position 7
Wiring the PRO 2020 8
Configuring the PRO 2020 9
Mounting the PRO 2020 10
Attaching the PRO 2020 using the adhesive strip ..........................................................................10
Attaching the PRO 2020 to the air vent ...........................................................................................11
Support 12
Technical data 13
Addendum 14
TomTom Telematics Limited Warranty 17
Copyright notices 19
3
TomTom PRO 2020
1. Display button
2. Display
3. ID Key reader
4. Integrated power data cable
Mounting adapter
Holder for air vent mount including self tapping screw
Fixings - adhesive strip, cleaning tissue
TomTom LINK 510 I/O cable
What’s in the box
4
Important safety notices and warnings
Important: Read the following safety instructions carefully. Read the instructions in this document
carefully.
TomTom Telematics accept no liability for damage that results from disregarding the safety
instructions. This document is part of the product. Keep it in a safe place. If you pass the unit on to
a new user, make sure you give them this document as well.
Use with care
It is your responsibility to use best judgment, due care and attention when using this device. Don't
allow interaction with this device to distract you while driving. Minimise the time spent looking at
the device screen while driving. You are responsible for observing laws that limit or prohibit the
use of mobile phones or other electronic devices, for example, the requirement to use hands-free
options for making calls when driving. Always obey applicable laws and road signs, especially
those relating to your vehicle’s dimensions, weight and payload type. TomTom does not
guarantee the error-free operation of this device and shall not be liable for any penalties arising
from your failure to comply with applicable laws and regulations.
Safety messages
Please read and take note of the following important safety advice:
Check your tyre pressures regularly.
Service your vehicle regularly.
Medication can affect your riding or driving ability.
Always use seat belts if available.
Don’t drink and drive.
Most accidents happen less than 5 km / 3 miles from home.
Obey the rules of the road.
Always use your turn indicators.
Every 2 hours, take a break for at least 10 minutes.
Keep your seat belts on.
Keep a safe distance from the vehicle in front.
Before setting off on a motorbike, fasten your helmet correctly.
When riding a motorbike, always wear protective clothing and equipment.
When riding a motorbike, be extra vigilant and always ride defensively.
Safety first
5
Use of this product is restricted in some areas
The TomTom PRO 2020 may interfere with electrical devices such as cardiac pacemakers, hearing
aids and aviation equipment. Interference with these devices may endanger the health or life of
you or others. Pacemaker manufacturers recommend that a minimum of 15cm / 6 inches be
maintained between the device and a pacemaker to avoid potential interference with the
pacemaker. These recommendations are consistent with independent research and recommenda-
tions by Wireless Technology Research.
Danger of explosion
Parts of the TomTom PRO 2020 can cause sparks that can lead to explosions. This may endanger
human health and life. Do not use the unit in areas with high risk of explosion. When using a
TomTom PRO 2020 in a vehicle fuelled by liquefied gas, follow the safety regulations of the
country in which the vehicle is operated.
Damage caused through improper installation
The installation and initial operation of the unit must be performed by authorised personnel only,
for example, a qualified radio dealer or an automotive electronics workshop.
Risk of injury in case of accidents
Do not mount the unit or accessories in the inflation area of airbags or in the impact area for the
head or knees. Choose an installation location that will avoid interference with displays, safety
equipment and controls.
Damage to the chassis
Make sure you do not drill into parts of the chassis that have structural or security-related
functions. This is because you cannot be certain that they will function properly after modification.
Risk of fire
Make sure you do not drill into covered wiring harnesses, fuel lines or similar components. Drilling
into these can cause fire.
Repair and replacement
Repairs must be carried out by authorised and qualified personnel only. Never replace damaged
parts of the unit yourself. Send the defective unit to TomTom Telematics for repair. Only the
qualified staff of TomTom Telematics are authorised to repair or replace parts.
Damage to the device
Short-circuits inside the unit can be caused by contact with water or other liquids. The unit may be
damaged by contact with water. Use and store the unit in an area protected from water.
6
* Make sure this wire is fused with max. 10A.
Note: You require a TomTom LINK 510 to connect to your TomTom PRO 2020. To make use of
the full OptiDrive functionality you also require a TomTom LINK 105 installed in your vehicle
and connected to the TomTom LINK 510.
Connection overview
7
First you need to choose the correct position in which to install your PRO 2020.
Take the following into consideration:
Do not expose the PRO 2020 to direct sunlight and/or high temperature for long periods to
ensure proper operation.
Do not mount the PRO 2020 in the inflation area of airbags or in the impact area for the head
or knees. Choose an installation location that will avoid interference with displays, safety
equipment and controls.
Choose a place that allows best connection of the cable open wire ends to both vehicle power
and TomTom LINK.
Choosing the correct position
8
Connect the PRO 2020 to the vehicle power supply with the standard vehicle voltage (12 V/24 V)
and to the TomTom LINK 510 device installed in your vehicle. The three wires DAT, GND and
PWR+ (supply voltage) must be connected.
Prerequisites
For a successful installation of the PRO 2020 you need a TomTom LINK 510 installed in your
vehicle, that has the firmware version 8.0 or higher and a WEBFLEET ECO subscription or higher
assigned.
Make sure you have read the safety instructions and you have found the right place to mount your
PRO 2020. Ensure that after installation neither the device nor any wires can interfere with and
safety relevant functions or may cause any other danger.
Wiring
Important: Follow the order of connecting the wires as described below. Please also refer to the
TomTom LINK installation guide to avoid any errors or damages during installation.
1. Connect the GND wire (brown) to ground (clamp 31).
2. Connect the PWR+ wire (red) to the carry current (clamp 30).
The connection must be fused with max. 10A. If not, fuse the the PWR+ wire with one 2A fast
blow fuse.
3. Connect the DAT wire (green/white) to the OUT wire (green/white) of the IO cable for TomTom
LINK 510.
4. Insert the IO cable into the IO cable connector of the TomTom LINK 510.
5. Tap the screen of your PRO 2020 or press the Display On/Off button to check for correct
power wiring.
If you can see the main menu, the wiring was successful.
If the PRO 2020 device still shows that it is trying to connect or that the connection has failed,
check the wiring again. If this does not help please refer to our Customer Support team.
Wiring the PRO 2020
9
After you have properly wired your PRO 2020 you may need to configure your TomTom LINK
device in WEBFLEET.
If the output OUT of your TomTom LINK had not been configured for other usage before, it will be
automatically configured to be used for the PRO 2020.
To configure your TomTom LINK device to be used together with the PRO 2020, do the following:
1. Log in to WEBFLEET.
2. Find your vehicle and select it.
3. In the vehicle details panel, go to the section for Contract / Device.
4. Click Configure.
5. Go to the Inputs / Outputs tab.
6. For OUT select PRO 2020 from the list.
7. Click Save.
Configuring the PRO 2020
10
You have the following options to mount your PRO 2020:
Using the adhesive tape, to stick it to a plane surface.
Using the air vent mount holder.
Using the TomTom universal suction mount, offered as an additional accessory (Art#
9KZ1.001.00), for on dashboard mounting.
Using any mounting accessory with a hole pattern compatible with the AMPS industry
standard.
Attaching the PRO 2020 using the adhesive strip
You can use the adhesive strip to fix the PRO 2020 to your vehicle. Follow the safety instructions
in this document.
1. Choose a flat surface for accurate positioning of the unit.
2. Clean the surface with the supplied cleaning tissue, so that the surface is oil free, dry and
clean.
3. Remove the protective film from one side of the strip.
4. Stick the strip to the bottom side of the mounting adapter shown below.
Important: Use the strip only in combination with the mounting adapter.
5. Remove the protective film from the other side of the strip.
6. Place the mounting adapter with the adhesive strip on the prepared surface. Press it gently for
a few seconds until it sticks.
Note: The full strength of the strip will be reached after approximately 72 hours depending
on the temperature.
Mounting the PRO 2020
Autres manuels pour PRO 2020
1
Table des matières
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur