TomTom GO Manuel utilisateur

TomTom GO

What’s in the box1.

What’s in the box

* In the TomTom GO x30 HD Traffic, this is replaced by the TomTom HD

Traffic Receiver.

aYour TomTom GO AMicrophone

BCharging light

COn/off button

DLight sensor

EReset button

FSpeaker

GMemory card slot (SD card not

included) for optional

additional maps

HUSB connector

ITomTom connector / RDS-TMC

connector

JExternal antenna connector

KAudio out connector

bCar charger*

cWindscreen holder dDocumentation pack

eHome dock (GO 530, 730, 930) fUSB cable (GO 630)

Included with TomTom GO x30T

Included with TomTom GO 930 and 930T

Included with TomTom GO x30 HD Traffic

gRDS-TMC Traffic Receiver

hRemote control

iTomTom HD Traffic Receiver

APower indicator - Red light

BHD Traffic Receiver indicator - Blue light

Before you start...2.

Before you start...

Switching on and off

To switch your TomTom GO on or off, press and hold the On/Off button for 2

seconds. The first time you switch on, it may take a short while for your device

to start.

Note: In rare cases, your GO may not start correctly. If this happens, press the

reset button, then switch on the device again.

Setting up

To set up your TomTom GO you need to answer a few questions by tapping

the screen.

Important: Take care to select the correct language, since the language you

choose will be used for all menus and written instructions.

Battery notes

We recommend that you fully charge your TomTom GO the first time that you

connect it to your computer. It takes up to 2 hours to charge the battery

completely.

When you place your GO in the Home Dock or use the USB cable to connect

to your computer, you are asked if you wish to connect to the computer. If you

select No, the device will switch off if you do not tap the screen for three

minutes. This happens so that the battery can recharge at a faster rate.

For information on connecting to your computer, see Using TomTom HOME

on page 101.

Note: Your TomTom GO uses a small amount of battery power to remember

the last screen being shown when the device is switched off.

If you do not charge your GO for a prolonged period of time, the next time you

start your GO it will show the default starting screen. All other device settings

will still be maintained.

Improving reception

If your TomTom GO takes longer than 5 minutes to find your current position,

make sure that the device is in an open space away from tall objects, such as

buildings or trees.

When you connect your TomTom GO to your computer, you can use

TomTom HOME to download information about GPS satellite positions during

the next 7 days. This helps your GO to find your position faster.

Important: Some vehicles have heat reflective shielding in the windscreen.

This may prevent your GO from locating your current position.

The TomTom External Antenna Kit (available for purchase as an accessory)

can help to improve reception.

Windscreen holder

Use the windscreen holder to install your TomTom GO inside your car.

To attach the holder, press the suction cup firmly to the windscreen in your

car, in an area of the windscreen where the glass is flat.

Make sure that both the holder and your windscreen are clean and dry before

you attach the holder. Place the holder so that it does not interfere with your

view of the road.

Home dock / USB cable

The Home Dock or USB cable is used for charging your TomTom GO when it

is not in the car and for connecting your GO to your computer.

When connected to your computer, you can use TomTom HOME to manage

your GO. For information about TomTom HOME, see Using TomTom HOME

on page 101.

Take care of your TomTom GO

Never leave your TomTom GO or accessories on view when you leave the car

or they may become an easy target for thieves.

You can set a password for your TomTom GO which must be entered every

time you start your GO. For more information, see Using TomTom HOME on

page 101.

It is important to take care of your GO.

• Your GO is not designed for use in extreme temperatures and any such

exposure may cause permanent damage.

• Do not open the casing of your GO under any circumstances. Doing so may

be dangerous and will invalidate the warranty.

• Wipe or dry the screen of your GO using a soft cloth. Do not use any liquid

cleaners.

Driving View3.

Driving View When your TomTom GO starts, you are shown the Driving View along with

detailed information about your current location.

Tap the centre of the screen at any time to open the Main Menu.

Note:TheDriving View isshownin black andwhite until your GO locates your

current position.

ATap + and - to zoom in and out.

BYour current position.

CThe name of the next major road or road sign information, if applicable.

DNavigation instruction for the road ahead.

Tap this area to repeat the last spoken instruction and to change the

volume.

EThe name of the next street to turn onto.

FInformation about your journey such as journey time, remaining distance

and arrival time.

To select what will be shown, tap Status bar preferences in the Preferences

menu.

GGPS signal strength.

HTraffic bar

To set up Traffic information, tap the Traffic bar to open the Traffic menu or

tap TomTom Traffic in the Main Menu.

IQuick menu - For more information, refer to the full manual.

Enhanced Positioning Technology4.

Enhanced Positioning Technology Note: Enhanced Positioning Technology is available on the TomTom GO 930

and 930T.

Enhanced Positioning Technology or EPT estimates your location when GPS

reception is poor, such as when you drive between tall buildings.

Your GO uses positioning sensors to monitor your acceleration and direction

and then estimates your current location.

EPT only helps your GO to estimate your location. Calculating your precise

location is only possible when your GO receives a strong GPS signal.

When your GO is using EPT to estimate your location, the EPT icon is shown

on the status bar.

Your GO calibrates EPT automatically. If calibration is not complete when your

GO loses GPS reception, EPT cannot be used and the screen is shown in grey,

for example, when there is no GPS reception at the beginning of a journey.

AEPT icon.

BYour current position.

Calibration

Calibration is done automatically and requires no interaction from you.

However, it is useful to have basic understanding of the calibration procedure.

Your TomTom GO resets the positioning sensors each time the device is

switched on. To help improve accuracy in estimating your location, your GO

calibrates the sensors throughout your journey.

The following conditions are required for successful calibration:

• Your GO is receiving a strong GPS signal.

• The car has been stationary for at least 5 seconds and then travels along a

straight and level section of road for at least one minute.

Making your first journey5.

Making your first journey Planning a route with your TomTom GO is easy. To plan your first route, follow

the steps below.

Important: You should always plan your journey before you start driving. It is

dangerous to plan a route while driving.

1. Tap the screen to bring up the Main Menu.

Note: The buttons on your GO are shown in full colour unless a button is

currently unavailable. For example, the button named Find alternative... in

the Main Menu is not available until you have planned a route.

2. Tap Navigate to...

3. Tap Address.

When you enter an address, you can choose from the following options:

•City centre - tap this button to set your destination as the centre of a city

or town.

•Street and house number - tap this button to set an exact address as your

destination.

•Postcode - tap this button to enter a postcode as your destination.

Note: You can enter a postcode for any country. In the UK and the

Netherlands, postcodes are detailed enough to identify a house on their own.

In other countries you can enter a postcode to identify a town or area. You will

then have to enter a street and house number.

•Crossing or intersection - tap this button to set your destination as the

point where two streets meet.

•Spoken address - tap this button to set your destination by announcing

the address to your GO. For more information, see Voice address input

on page 21.

For your first journey, we will enter an exact address.

4. Tap Street and house number.

Note: When planning a trip for the first time your GO asks you to choose a

country. Your choice is saved and used for all routes you plan.

You can change this setting at any time by tapping the country flag.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are

shown. When your destination appears in the list, tap the name of the town

to set the destination.

Tip: Instead of typing the name, tap this button to say the address

by speaking to your GO.

For more information, see Voice address input on page 21

6. Start to type the name of the street and select it when it is shown.

As with the name of the town, the names of the streets that match what you

have typed are shown. When your destination appears in the list, tap the

name of the street to set the destination.

7. Now enter the house number of your destination and then tap Done.

8. Your GO asks if you need to arrive at a particular time. For this exercise, tap

NO.

The route is calculated by your GO. IQ RoutesTM is used to plan the best

possible route, using historical information about traffic speed on the roads.

9. When the route has been calculated, tap Done.

Your GO will immediately begin to guide you to your destination, using both

spoken instructions and on-screen directions.

Arrival times

When you plan a route, your TomTom GO asks you if you need to arrive at a

particular time.

Tap YES to enter a preferred arrival time.

Your GO calculates your arrival time and shows you whether you will arrive

on time.

You can also use this information to work out when you need to leave. If your

GO shows that you will arrive 30 minutes early, you can wait and leave in 30

minutes time, rather than arrive early.

Your arrival time is constantly recalculated during your journey. The status bar

shows whether you will arrive on time or if you are going to be late, as shown

below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before

the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the

time you entered, it is shown in yellow.

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered,

it is shown in red.

Status bar

preferences

Tap Status bar preferences in the Preferences menu, to enable or disable

arrival time notifications.

Select the required options on the first menu screen and then tap Done.

To enable arrival time notifications, select Show leeway to arrival time.

To disable arrival time notifications, unselect Show leeway to arrival time.

Autres manuels pour GO

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TomTom GPS

TomTom

TomTom TNS400 Manuel utilisateur

TomTom

TomTom Hands-Free Car Kit Manuel utilisateur

TomTom

TomTom Go 730 Manuel

TomTom

TomTom ONE Car GPS Receiver Manuel utilisateur

TomTom

TomTom Go 2435TM Manuel utilisateur

TomTom

TomTom Blue&Me-TomTom 2 LIVE Manuel utilisateur

TomTom

TomTom PRO 82 SERIES Manuel utilisateur

TomTom

TomTom GO 510 Manuel utilisateur

TomTom

TomTom One XL Manuel utilisateur

TomTom

TomTom ECLIPSE Manuel utilisateur

TomTom

TomTom GO Manuel utilisateur

TomTom

TomTom GO Manuel utilisateur

TomTom

TomTom GO Manuel utilisateur

TomTom

TomTom LINK 510 Manuel utilisateur

TomTom

TomTom One XL Manuel utilisateur

TomTom

TomTom Blue&Me- Manuel utilisateur

TomTom

TomTom VIA Manuel utilisateur

TomTom

TomTom Car Navigation System ONE Manuel utilisateur

TomTom

TomTom ONE/XL Manuel utilisateur

TomTom

TomTom GO PROFESSIONAL Series Manuel utilisateur

TomTom

TomTom Carminat GPS Receiver Manuel utilisateur

TomTom

TomTom LINK 201 Manuel utilisateur

TomTom

TomTom One XL Manuel utilisateur

TomTom

TomTom 4CT50 Manuel utilisateur

Manuels GPS populaires d'autres marques

Raven

Raven Cruizer II Manuel

Hama

Hama 53118 Manuel utilisateur

Garmin

Garmin SOUNDER 125 Manuel utilisateur

Garmin

Garmin DEZL 580 Manuel utilisateur

Jigabot

Jigabot EX Manuel utilisateur

Pointer

Pointer Cellocator CelloTrack XT LTE Guide d'installation

Queclink

Queclink GV55LITE Manuel utilisateur

Voxson

Voxson Voxtrack GPS500 Manuel d'instructions

Garmin

Garmin ECHOMAP PLUS Manuel utilisateur

Starcom Systems

Starcom Systems Kylos Compact Manuel utilisateur

Garmin

Garmin 15 H Series Manuel utilisateur

Cobra

Cobra Marine MC 600Ci Manuel utilisateur

Cellocator

Cellocator CelloTrack T Manuel utilisateur

Enfora

Enfora Mini-MT GSM2228UG001 Manuel utilisateur

Magellan

Magellan eXplorist 100 Manuel utilisateur

LTE

LTE G50B Manuel utilisateur

Garmin

Garmin DEZL OTR500 Manuel utilisateur

SkyGolf

SkyGolf SkyCaddie SG1 Manuel utilisateur