TMG TMG-AJT10 Manuel utilisateur
PRODUCT MANUAL
v.2022.09.01
• Please read and understand the product manual completely before assembly
• Check against the parts list to make sure all parts are received
• Wear proper safety goggles or other protective gears while in assembly
• Do not return the product to dealer. They are not equipped to handle your requests.
Missing parts or have questions on assembly?
TOLL FREE: 1-877-761-2819
WARNING
www.tmgindustrial.com
TMG-AJT10MODEL
1,000 LB TRANSMISSION
JACK LOW PROFILE
SPECIFICATION
MAXIMUM CAPACITY 500KG
RETRACTED HEIGHT 215MM
MAXIMUM HEIGHT 565MM
WARNING
• Read and understand all operating instructions before use.
• The vehicle must be properly supported and blocked before starting repairs.
• Use a transmission jack of the proper size and capacity to handle the anticipated
load. This jack is rated for a maximum load of 500kgs. Do not overload beyond
the rated capacity. Overloading may cause damage to or failure of the jack.
• Keep hands, fingers and arms away from moving parts of the jack at all times.
• Lower the load slowly and avoid sudden starts or stops that may cause the load
to shift.
• This jack is designed for use on a hard, level surface capable of sustaining the
load. Use on other surfaces can result in jack instability and possible loss of load.
• This transmission jack is designed and intended for use by properly trained and
experienced personnel only. If you are not familiar with the proper and safe
operation of a transmission jack do not operate the jack until training and knowl-
edge have been obtained.
• The use of this jack is limited to the removal, installation and transportation in the
lowered position of transmissions and differentials.
• Failure to comply with all of these warnings may cause loss of load, damage to
the jack and or failure of the jack resulting in serious injury or property damage.
www.tmgindustrial.com P1/3 TOLL FREE: 1-877-761-2819
OPERATION
1. Move the jack into position
2. Turn the knob fully clockwise to close the valve
3. Move the pump lever up and down to raise the saddle
4. Adjust the angle screws to align with the shape of the transmission
5. Adjust the angle brackets and the chain to secure the transmission on the saddle
6. Remove the transmission from the vehicle
7. Turn the knob counter clockwise slowly to lower the saddle. Always lower the
saddle slowly. Always transport the load in the lowered position with the chains
securely fastened.
8. Reverse this procedure when mounting the transmission.
www.tmgindustrial.com P2/3 TOLL FREE: 1-877-761-2819
MAINTENANCE
The hydraulic cylinder assembly contains hydraulic fluid that must be kept within 80%
of full at all times for proper operation. To check the level and to fill:
1. Remove the screw
2. Fill with clean hydraulic fluid only
3. Replace the screw
4. Lubricate the shaft threads of the angle screw assembly with tube grease when
necessary.
www.tmgindustrial.com P3/3 TOLL FREE: 1-877-761-2819
Table des matières
Autres manuels TMG Jack
TMG
TMG TMG-ALM68 Manuel utilisateur
TMG
TMG TMG-AJX22 Manuel utilisateur
TMG
TMG TMG-AJS03 Manuel utilisateur
TMG
TMG TMG-AJA12 Manuel utilisateur
TMG
TMG TMG-AJF04L Manuel utilisateur
TMG
TMG TMG-AJF03 Manuel utilisateur
TMG
TMG TMG-AJA30 Manuel utilisateur
TMG
TMG TMG-AJT11 Manuel utilisateur
TMG
TMG TMG-AJF03L Manuel utilisateur
Manuels Jack populaires d'autres marques
VEVOR
VEVOR TJD-12000SP-F Manuel utilisateur
ULTIMATE SPEED
ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur
Stels
Stels 51131 Manuel utilisateur
Bushranger
Bushranger RJX01 Manuel utilisateur
Clarke
Clarke CTJ2500QLG Manuel d'installation et d'exploitation
Valex
Valex 1650520 Manuel utilisateur
