TLS Electronics 875760 Manuel utilisateur

875760 HDbaseT/HDMI/Audio Matrix 4x4

Manual

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 3 -

Thank you for purchasing this product. For optimum performance and safety,

please read these instructions carefully before connecting, operating or adjust-

ing this product. Please keep this manual for future reference.

SURGE PROTECTION DEVICE RECOMMENDED

This product contains sensitive electrical components that may be damaged by

electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge

protection systems is highly recommended in order to protect and extend the life

of your equipment.

SAFETY AND NOTICE

1. The transmission distances of HDMI over UTP cables are measured using

TE CONNECTIVITY 1427071-6

2. EIA/TIA-568-B termination (T568B) and “AWG24/1 solid wire” for CAT

cables is recommended for best performance.

3. DO NOT use 568A/568B standard mixed CAT cable (cross-over cable)

because there are 2 pairs swapped, this will make POE OVER-CURRENT

and damage POE components. Please use straight-through CAT cable (both

RJ45 headers are 568A or 568B standard).

4. It is recommended that power up the device after connections of source, sink

and CAT cable.

5. To reduce the interference among the unshielded twisted pairs of wires in

CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling with or in close

parallel proximity to mains power cables. Shielded CAT cables can be used

to improve EMI problems, which is worsen in long transmission.

6. Because the quality of the CAT cables has the major effect on how long the

transmission limit can achieve and how good is the received picture quality,

the actual transmission range is subject to one’s choice of CAT cables.

7. Do not substitute or use any other Power Supply other than the

enclosed unit, or a TLS electronics GmbH approved Replacement Part.

Doing so will void the warranty and potentially expose the user to

dangerous voltages resulting in an electrical shock.

8. Do not disassemble the device for any reason. Doing so will void the manu-

facturer’s warranty. Also, our unique case is an integral part of the design of

this unit and is responsible for cooling and circuitry shielding. Any modifica-

tions to this case will potentially cause malfunction and product failure.

9. Do not expose the device to water, moisture, or liquids. Possible electric

shock may result as well as failure of the unit to operate.

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 4 -

Table of Contents

1. Introduction.............................................................................................5

2. Features.....................................................................................................5

3. Panel Descriptions.......................................................................................6

4. Remote Control Descriptions......................................................................10

5. Specifications...............................................................................11

6. Application Diagram...........................................................................12

7. Package Contents......................................................................................13

8. RS-232 Pin Assignment.......................................................................13

9. RS-232 and Telnet Commands ...............................................................14

10. GUI control..............................................................................................16

11. Maintenance..............................................................................................27

12. Warranty Policy...................................................................................27

13. Limitations of Warranty........................................................................27

14. Exclusive Remedies...........................................................................28

15. RMA Policy...........................................................................................28

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 5 -

Introduction:

The HDBaseT/HDMI/Audio Matrix 4x4 routes four Hi-Def sources to any four

HDTV displays, supporting 1080p Full HD up to 4K@30Hz UHD plus all 3D

formats, along with multichannel digital audio formats such as Dolby® True HD

and DTS-HD® Master Audio™. Embedded audio extractors can extract the

audio and output via L/R or Coaxial. Volume can be controlled for analogue

audio out. Based on HDBaseT Lite chipset inside, the output distance can reach

up to 70m via Cat5e/Cat6. Each source can be routed to any display using the

front-panel push buttons, IR remote control, RS-232 interface, or via TCP/IP.

Features:

•HDCP 2.2 compliant

•Supports resolutions up to 1080p@60Hz, 4K@30Hz, 36-bit deep color

•HDBaseT Lite chipset inside for the output distance up to 70m.

•Matrix can power the remote receivers, with POH, no power supply needed

for the receivers.

•Allows any source to be displayed on multiple displays (HDBaseT & HDMI)

at the same time

•Allows any HDMI display to view any HDMI source at any time

•Dolby TrueHD and DTS-HD master audio pass through HDMI output

•Volume control with Telnet and RS232 on deembedded audio

•Advanced EDID management for rapid integration of sources and displays

•Front-panel LCD display for status feedback

•Multiple switching mode: push-in button, IR remote control, RS-232 control,

and TCP/IP control

•Easy installation with rack-mounting ears

•Full 3D pass- through.

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 6 -

Panel Descriptions

Front Panel

1. LCD display---Show the status of input-output selection, EDID info and so on.

2. IR receiver window----Receive the IR from the remote control.

3. Power LED indicator---Indicate the status of the power for the matrix.

4. Power button---Press to power on/off the matrix.

5. HDMI output selection button 1 to 4---First Press - select the output from

button 1 to button 4

12. HDMI input selection button 1 to 4---Second Press - select the input from

button 1 to button 4

6. All button for HDMI outputs---Press to select all of the outputs from 1 to 4.

7. Menu button---Press to enter EDID set mode. Three EDID segments will

display on the LCD panel formatted as: INPUT VIDEO AUDIO, for example:

IN1 1080P 2.0CH, means to set 1080P 2.0CH EDID to INPUT1. The blinking

segment is the one can be changed currently. Segment content items as

below:

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 7 -

INPUT

VIDEO

AUDIO

Note

IN1 1080I 2.0CH.

IN2 1080P 5.1CH

IN3 3D 7.1CH

IN4 D1024 D1024=DVI 1024 x 768

IN5 D1080 D1080=DVI 1920 x 1080

IN6 D1200 D1200=DVI 1920 x 1200

IN7 OUT1 OUT1=Copy OUTPUT1 EDID to INPUTx

ALL OUT2 ALL=Set EDID to ALL INPUTs

OUT2=Copy OUTPUT2 EDID to INPUTx

OUT3 OUT3=Copy OUTPUT3 EDID to INPUTx

OUT4 OUT4=Copy OUTPUT4 EDID to INPUTx

OUT5 OUT5=Copy OUTPUT5 EDID to INPUTx

OUT6 OUT6=Copy OUTPUT6 EDID to INPUTx

OUT7 OUT7=Copy OUTPUT7 EDID to INPUTx

OUT8 OUT8=Copy OUTPUT8 EDID to INPUTx

8. Up selection button--- Press to change segment’s value.

9. ESC---Press to quit EDID set mode.

10. Lock LED indicator---Indicate the status of Lock.

11. Lock button---Press to lock the buttons of the front panel.

12. HDMI input selection button 1 to 4---Press to select the input from 1 to 4.

13. PTP button---Press to mirror all inputs and outputs (e.g. output 1 to input1,

output 2 to input2 and so on).

14. Selection button---Press to select segment to change setting. Selected

segment will be blinking.

15. Down selection button---Press to change segment’s value.

16. Enter button--- Press to set EDID to specified INPUT or copy EDID from

specified OUTPUT to specified INPUT.

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 8 -

Back Panel

1. GND --- Connect to ground.

2. IR inputs 1 to 4 --- 3.5mm stereo phone-jack, work with control processor.

3. IR outputs 1 to 4 --- 3.5mm mono phone-jack, connect to IR transmitter cable.

4. RS232 port with each HDBT out--- Connect to PC, and work with the remote

receiver.

5. Coaxial digital audio output --- Extracted audio corresponding with the HDMI

video output

6. L/R analog audio output --- Extracted audio corresponding with the HDMI

video output.

7. TCP/IP port – TCP/IP control

8. RS232 port – For control the matrix from PC or control processor

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 9 -

9. DIP switch – Used for global EDID settings

3 2 1 0 EDID type

Combination of DIP positions

0 0 0 0 1080P 2.0CH

0 0 0 1 1080P 5.1CH

0 0 1 0 1080P 7.1CH

0 0 1 1 1080i 2.0CH

0 1 0 0 1080i 5.1CH

0 1 0 1 1080i 7.1CH

0 1 1 0 3D 2.0CH

0 1 1 1 3D 5.1CH

1 0 0 0 3D 7.1CH

1 0 0 1 4K 2.0CH

1 0 1 0 4K 5.1CH

1 0 1 1 4K 7.1CH

1 1 0 0 DVI 1280x1024

1 1 0 1 DVI 1920x1080

1 1 1 0 DVI 1920x1200

1 1 1 1 Software Control EDID

10. HDMI inputs 1 to 4--- Connect HDMI sources

11. HDBT outputs 1 to 4--- Work with remote receivers for long distance trans-

mission.

12. HDMI outputs 1 to 4--- Output for displays, AVR etc.

13. IR extension receiver input --- 3.5mm stereo phone-jack, connect to IR

receiver cable to receive the IR from remote of the matrix.

14. Power port--- Use included 24V/3.5A DC adaptor to power the matrix.

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 10 -

Remote Control Description

Output and Input select

A. OUTPUT-X select INPUT-Y:

1. Press OUTPUT-X (X means 1 to 4 of outputs)Press INPUT-Y( Ymeans

1 to 4 of inputs )

2. Press OUTPUT-X (X means 1 to 4 of outputs)press the left and right

arrow buttons to select the input.

B. All outputs select INPUT-Y: Press ALL button in zone OUTPUTPress

INPUT-Y button ( Y means 1 to 4 of inputs ), then INPUT-Y switched to ALL

OUTPUTS

C. Mirror all inputs and outputs (Ex. Input 1 to output 1, input 2 to output 2, etc):

Press PTP button in Zone OUTPUT

EDID Set Up

A. Fixed EDID to INPUT-Y/ALL

Press 1080I/1080P/3D/4KPress 2.0CH/5.1CH/7.1CHINPUT-Y/ALL

button in Zone INPUT

875760 HDBaseT/HDMI/Audio Matrix 4x4

TLS electronics GmbH [email protected] - 11 -

B. Copy EDID of OUTPUT-X to INPUT-Y/ALL

Press COPY buttonPress OUTPUT-X buttonPress INPUT-Y/ALL button

C. User defined EDID to INPUT-Y/ALL

Press USER1/USER2 buttonPress INPUT-Y/ALL

NOTE: Pressing button sequence should be finished in 5 seconds, otherwise,

operation discarded.

Manual Output and Input select

First Press: OUTPUT select, output button 1 to 4

Second Press: INPUT select, output button 1 to 4

Specifications:

Bandwidth 2.97Gbps per color

Video Input Connectors 4x HDMI Type A, 19-pin, female

Video Output Connectors 4x HDMI Type A, 19-pin, female, 4x RJ45 Connector

Audio Output Connectors 4x RCA(SPDIF), 4x L/R

RS232 Serial port DB-9, female

TCP/IP Control 1x RJ45, female

IR input ports 5x3.5mm stereo jack

IR output ports 4x3.5mm mono stereo jack

Rack-Mountable rack ears included

Dimensions(Lx Wx D) 428mm x 235mm x 43mm, w/o feet

Shipping Weight 2.7KG

Operating Temperature 32°F to 104°F (0°C to 40°C)

Storage Temperature -4°F to 140°F (-20°C to 60°C)

Power Supply 24V/3,5A DC

Table des matières

Autres manuels TLS Electronics Système de contrôle

TLS Electronics

TLS Electronics QuickControl XL Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur