Timeguard TRT034N Manuel utilisateur
Installation & Operating Instructions
7 Day Digital Programmer
1 Channel – Surface Mount
Model: TRT034N
1
1. General Information
These instructions should be read carefully and retained for further reference
and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the
Programmer is switched off and the circuit supply fuses are removed
or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the
installation of this Programmer and install in accordance with the current
IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this Programmer is
fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.
• To clean use a clean dry cloth only. Do not use any liquid cleaners.
3. Technical Specifications
• 230V AC 50 Hz
• This thermostat is of Class ll Construction and must not be earthed
• Switch Rating: 3(1)A
•Switch Type: Single pole, double throw (SPDT)
change over contacts
•Connection Type: 3 wire
•Installation Type: Surface mount with wall plate
• Micro Disconnection: Type 1.B control action
•Operating Temperature Range: 0°C to +40°C
• Programme: 5 day plus 2, or 7 day set by DIP switches
• Time Control Periods: 3 per day with copy function
• Clock Format: 12 hour AM/PM or 24 hour
• Summer/Winter Changeover: Day light saving, GMT or BST
• Holiday Mode: 0 to 31 day Programme suspension
• Boost Function: 1, 2 or 3 hour
2
• Battery Backup: 7 Day, factory fitted rechargeable
(non-replaceable)
• Illumination: Blue LED illuminated on setting
for button surrounds and display
• CE Compliant
• Dimensions (H x W x D): 90 x 135 x 30mm
TRT034N Front View
The heating symbol will show
when heat is demanded
12hr am/pm
or 24hr clock
timer display
(illuminated
on setting)
Advance to next Programme,
ON/OFF override and copy function
Up down selection
buttons
1, 2 and 3 hour boost
function (illuminates
on setting)
Display light/Holiday
mode setting button
Flip down cover
conceals setting
buttons
3
4. Siting
• The TRT034N should be located at a position which eases wiring runs
and gives good access for Programming.
• It should be mounted approximately 1.5m above floor level.
5. Installation
5.1 Ensure the mains supply is switched off and the circuit supply fuses
are removed or the circuit breaker turned off.
5.2 Remove the wall plate from the unit, by undoing the retaining screws,
and pivoting the bottom of the unit outwards. The TRT034N body can
then be lifted off.
5.3 Mark the position of the mounting holes on the wall using the wall plate
as a template. Drill out the mounting holes taking care to avoid any
joists, electrical cables or water/gas pipes that may be hidden beneath
the surface. Insert the rawl plugs into the holes.
5.4 Pass the 230V 50Hz mains supply and load cables through the opening
of the wall plate. Allow sufficient excess cable to wire up the unit, but
not too much to make it difficult to close the unit to the wall plate.
5.5 Fix the wall plate to the wall using the correct mounting screws for the
rawl plugs installed. The retaining screws which secure the unit to the
wall plate should be at the bottom.
5.6 Terminate the cables into the terminal block ensuring correct polarity
is observed and that all bare conductors are sleeved (See section 6.
Connection Diagram). Make sure that the curved washer grips
the conductor.
5.7 To reinstall the unit onto the wall plate, first ensure the wall plate
retaining screws are loosened enough to clear the TRT034N body,
then engage the top of the TRT034N onto the wall plate retaining tabs,
and push firmly downwards and then upwards. There will be some
resistance from the terminals.
5.8 Once in place, secure with the retaining screws making sure
not to over tighten.
4
TRT034N Wall Plate
Alternate mounting holes
Wall plate retaining screws
Retaining tabs
Mounting
holes
Loop terminal
NC NO
BOILER
L
230V AC 50Hz
MAINS SUPPLY Supply
Neutral
Supply
Live
N
Switch Live from NO
(normally open contact
for heating) to Boiler
5
6. Connection Diagram
Connect the 230V 50Hz mains supply and load cables to the terminal block
which are marked as follows;
• Note: Check boiler instructions before connecting.
230V 50Hz Mains Supply
Live Supply (Brown or Red) to L
Neutral Supply (Blue or Black) to N
A ‘Loop Terminal’ is provided should a 3 core cable
be used
Load (Boiler)
Switch Live (Brown or Red) to NO
6
DIP switch position label
DIP switches for 5-2
or 7 day Programming
7. DIP Switch Settings
• Decide whether weekday/weekend (5-2) or individual (7) day programming
is required, and set the DIP switches in the correct position on the rear of
the unit. A reset will be required after changing the DIP switch positions.
TRT034N Rear of Unit
7
8. Reset from Power-up
• Restore mains to the unit after making sure to check all system wiring
is complete, and after you have selected the desired DIP switch settings.
• Press the reset button located beneath the flip down cover on the front
of the unit, all of the characters will briefly appear on the display,
followed by the 12hr clock format screen.
• After 1 minute the screen will time out showing a default time
of 12:00AM.
• There are 3 timed controlled periods per day, and the default
Programmes are as follows;
Heating (HTG)
06:00AM ON
08:00AM OFF
10:00AM ON
12:00PM OFF
06:00PM ON
10:00PM OFF
9. Setting the Time and Date
9.1 To alter the time and date at any time, press and hold the Select button
for 3 seconds, the display light will illuminate.
9.2 The default clock format is 12Hr which will be displayed on the screen.
8
9.3 Use the Up/Down arrow buttons to either select 24Hr format, or leave
it at 12Hr format, and then press the Select button once to confirm.
9.4 The hour will to flash, use the Up/Down arrow buttons to alter the hour
and press the Select button once to confirm.
9.5 The minutes will flash, use the Up/Down arrow buttons to alter the
minutes and press the Select button once to confirm.
9.6 The year will flash, use the Up/Down arrow buttons to alter the year
and press the Select button once to confirm.
12Hr AM/PM format Use the Up/Down arrow
buttons to change
the time format
24Hr format Use the Select
button to
confirm
Use the Up/Down
arrow buttons to
change the hour
The hour will flash Example of
12Hr AM/
PM format
Use the Select
button to
confirm
Use the Up/Down
arrow buttons to
change the minutes
The minutes will flash Use the Select
button to
confirm
Use the Up/Down
arrow buttons to
change the year
The year will flash Use the Select
button to
confirm
9
9.7 The month will flash, use the Up/Down arrow buttons to alter the year
and press the Select button once to confirm.
9.8 The day will flash, use the Up/Down arrow buttons to alter the day
and press the Select button once to confirm.
9.9 The daylight saving option (GMT=OFF/BST=ON) will flash, by default this will
be set to OFF. Use the Up/Down arrow buttons to alter the setting. Press the
Select button once to confirm and return to re-enter the date and time from
the beginning, or press the Set button once to confirm and exit.
Use the Up/Down
arrow buttons to
change the month
The month will flash Use the Select
button to
confirm
Use the Up/Down
arrow buttons to
change the day
The day will flash Use the Select
button to
confirm
The DLS will flash,
OFF for GMT by
default
The DLS set to
ON for BST
Use Set to
confirm
and exit
Use Select to confirm
and return to re-enter
time & date
Main screen
showing day,
time and
output status
Note:
• If no button is pressed, it will time out after 60 seconds and return to the
mains screen showing day, time and output status.
• The display light will also time out after 15 seconds after the last button
is pressed.
• The Set button can be pressed to exit the date and time entry at any stage.
Table des matières
Autres manuels Timeguard Thermostat
Timeguard
Timeguard TRT044 Manuel
Timeguard
Timeguard TRT036N Manuel
Timeguard
Timeguard TRT032N Manuel utilisateur
Timeguard
Timeguard TRT030DN Manuel utilisateur
Timeguard
Timeguard TRT030N Manuel utilisateur
Timeguard
Timeguard TRT035N Manuel utilisateur
Timeguard
Timeguard TRT037 Guide produit
Timeguard
Timeguard TRT05 Manuel
Timeguard
Timeguard TRT034 Guide produit
Timeguard
Timeguard MLTP180BK Manuel
Timeguard
Timeguard ProgramaStat TRT037 Guide produit
Timeguard
Timeguard TRTD7 Manuel utilisateur
Timeguard
Timeguard TPT44 Manuel utilisateur
Timeguard
Timeguard TRT031 Guide produit
Timeguard
Timeguard TRT037N Manuel
Timeguard
Timeguard TRT033N Manuel utilisateur
Timeguard
Timeguard ProgramaStat Guide produit
Timeguard
Timeguard TRT044 Guide produit
Timeguard
Timeguard TRT05 Manuel
Timeguard
Timeguard TRT035 Guide produit
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
