TIE DOWN 70910 Guide de démarrage rapide

404-344-0000 • www.tiedown.com

605 Stonehill Drive SW, Atlanta, GA 30336

[email protected]

Do not throw away these instructions!

Read and understand these instructions before

using this device. For any questions, please call

(404) 344-0000.

Instruction #08377

E1834; Rev. 3/29/21

Adjustable Swing Gate

Installation and Use

Part #70910

WARNING: This product can expose you to chemicals including Nickel, which is known to the

State of California to cause cancer. For more information go to: www.P65Warnings.ca.gov

Swing Gate Hinge Assembly

Wheeled Gate End Section

Center Adjustable

Swing Gate Section

Hinge Gate End Section

The Adjustable Swing Gate can be

set up to ﬁt 70” to 85” gate widths.

Page 2 of 4

Adjustable Swing Gate

Installation and Use

Part #70910

INSTALLATION

Step 1

Position the Adjustable Swing Gate

between the desired guardrail opening.

Remove the outer u-bolt, washers, and

nylock nuts.

TIE DOWN Safety Products Division • 800-241-1806 • 404-344-0000 • www.tiedown.com

Step 2

Slide the Adjustable Swing Gate into desired

position. The open end of the swing hinge

should ﬁt ﬂush against the guardrail.

Place the u-bolt through the mounting holes

of the Swing Hinge by placing over the

inside of the guardrail. Secure the u-bolt

with the washers and nylock nuts.

Do not fully tighten the nylock nuts.

U-bolt passes over the inside

guardrail through the hinge.

Secure with washers and nuts

Remove u-bolt, nuts, and washers

Page 3 of 4

Adjustable Swing Gate

Installation and Use

Part #70910

TIE DOWN Safety Products Division • 800-241-1806 • 404-344-0000 • www.tiedown.com

Step 3

Extend the Wheeled Gate Section

until it meets the other guardrail.

The Adjustable Swing Gate can be

adjusted 70” up to 85”.

Step 4

Position and slide the Center Adjustable

Swing Gate Section through the center of

the two guardrail end sections.

Make sure the Adjustable Swing Gate opens

and closes smoothly.

Secure the Center Adjustable Section with 4

self tapping screws, as shown to the right.

Mount the screws using the holes on the

inside of the Center Adjustable Section.

Tighten the nylock nuts on the Swing Gate

Hinge.

Self tapping screws (x4)

Tighten Swing Gate

Hinge with nylock

nuts

Slide outward until the

latch fits around the opposite

guardrail

www.tiedown.com

ISO 9001:2015 Certification

Intellectual property of TIE DOWN Inc.

Instruction #08348 (E1834 Rev. 3/29/21)

Safety Products Division

605 Stonehill Drive SW

Atlanta, Georgia 30336

800-241-1806 • 404-344-0000

Page 4 of 4

Step 5

Secure the Swing Gate by lowering the Swing Gate

Latch. Wrap the safety chain around both guardrail

posts and insert the end of the safety chain into the

key hole slot.

Swing Gate Latch

(Shown Open)

Wrap safety chain

around both

guardrails

Adjustable Swing Gate

Installation and Use

Part #70910

IMPORTANT!

Guardrail Outriggers MUST be used at both ends of any

interruption in continuous guardrail sections, or at both ends

of a continuous guardrail section.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TIE DOWN Équipements de sécurité

TIE DOWN

TIE DOWN 70818 Manuel utilisateur

TIE DOWN

TIE DOWN Parapet Anchor Manuel utilisateur

TIE DOWN

TIE DOWN PENETRATOR Manuel utilisateur

TIE DOWN

TIE DOWN Big Foot 60060US Mode d’emploi

TIE DOWN

TIE DOWN 72874 Manuel utilisateur

TIE DOWN

TIE DOWN 70853 Manuel utilisateur

TIE DOWN

TIE DOWN Hippo Anchor 65219 Manuel utilisateur

TIE DOWN

TIE DOWN Juggernaut Manuel utilisateur

TIE DOWN

TIE DOWN 14367 Guide de démarrage rapide

Manuels Équipements de sécurité populaires d'autres marques

Innova

Innova Xtirpa Mode d’emploi

bolle SAFETY

bolle SAFETY B810 Manuel utilisateur

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur

Hiltron security

Hiltron security POWER8E Mode d’emploi

Hatco

Hatco B-950P Manuel utilisateur

Sitec

Sitec TX MATIC Manuel utilisateur

TEUFELBERGER

TEUFELBERGER GRIP 12 Manuel utilisateur

MSA

MSA PremAire System Manuel utilisateur

AMC

AMC 1022M Series Manuel utilisateur

Trinity

Trinity CASS S3 Manuel utilisateur

CMC

CMC Helitack HotSeat Manuel utilisateur

Force

Force P-35 Manuel utilisateur

ACM

ACM SAFETY D200 Manuel du produit

Honeywell

Honeywell Miller H-Design DuraFlex Manuel de l'opérateur

ROCK

ROCK P-451 AS Manuel utilisateur

Power first

Power first 2XYR7A Manuel de service

SCHUBERTH

SCHUBERTH SHP 28-C Manuel utilisateur

Trango

Trango CINCH Manuel utilisateur