THORLABS CS20K2 Manuel utilisateur
LED UV Curing System
2020
CS20K2 (365 nm),
CS20K3 (385 nm),
CS20K4 (395 nm),
CS20K5 (405 nm)
Operation Manual
Version:
Date: 1.0
13-Nov-2020
Copyright © 2020 Thorlabs
Foreword
Contents
1 General Information 1
11.1 Ordering Codes and Accessories 21.2 Requirements 21.2.1 Hardware Requirements 21.2.2 Software Requirements
2 Getting Started 3
32.1 Parts List
3 Operating Instructions 4
43.1 Operating Elements 53.2 Basic Setup 63.3 Display Operation 63.3.1 Settings 73.3.2 Continuous Mode 73.3.3 Timer Mode 73.3.4 Configuration Mode 83.3.5 Slope Mode 93.3.6 Irradiance Mode 103.3.7 User Limit 103.3.8 About 103.4 Computer Interface 103.4.1 Software Installation 103.4.1.1 Install Device Drivers 113.4.2 Graphic User Interface (GUI) 123.4.2.1 Menu Bar 133.4.2.2 Continuous Mode 143.4.2.3 Timer Mode 143.4.2.4 Configuration Mode 153.4.2.5 Slope Mode 163.5 Foot Switch Operation 163.6 Control of Other LEDs Using CS2020 Driver
4 Maintenance and Service 17
174.1 Version Information 174.2 Troubleshooting
5 Appendix 19
195.1 Technical Data 205.2 Dimensions 225.3 Spectra
© 2020 Thorlabs
We aim to develop and produce the best solutions for your
applications in the field of optical measurement techniques. To help
us to live up to your expectations and constantly improve our
products, we need your ideas and suggestions. We and our
international partners are looking forward to hearing from you.
Thorlabs GmbH
Warning
Sections marked by this symbol explain dangers that might result in
personal injury or death. Always read the associated information
carefully before performing the indicated procedure.
Please read this advice carefully!
This manual also contains "NOTES" and "HINTS" written in this form.
Attention
Paragraphs preceded by this symbol explain hazards that could
damage the instrument and the connected equipment or may cause
loss of data.
Note
© 2020 Thorlabs1
CS20Kx
1 General Information
The Thorlabs LED spot UV curing systems CS20Kx are designed for curing (hardening) of ma-
terial like certain inks, coatings, or adhesives which are formulated with photoinitiators and re-
sins. When exposed to the correct energy and irradiance in the required band of UV light, poly-
merization occurs, such that the adhesives harden or cure. Usually, this reaction is a matter of
a few seconds. This can be advantageous for any application that requires critical alignment or
exact positioning. Applications include glass and plastic bonding, optical fiber coatings and
coating of flooring.
The CS20Kx system is availabe for four different wavelength ranges: 365 nm, 385 nm, 395 nm
and 405 nm, named CS20K2, CS20K3, CS20K4 and CS20K5 respectively. The system con-
sists of a CS2020 driver and a handheld light source with the respective LED and optics. Op-
tionally, different optics are available to vary the size of the focus spot.
The system can be operated using either the display on the CS2020 driver or remotely using
the software. For flexibility in operation, the software allows to limit exposure time, reproducibly
increase and decrease intensity and to store up to 10 user defined settings.
With the CAB-CS20 adapter cable, the CS2020 can alternatively be used with Thorlabs moun-
ted LEDs as an assembled system.
Attention
Please find all safety information and warnings concerning this product in the chapter Safety
in the Appendix.
1.1 Ordering Codes and Accessories
CS20K2 LED UV Curing System for applications at 365 nm. Included: CS2020 con-
trol unit; respective Handheld LED light source CS20H2 with safety shield
and goggles; power supply.
CS20K3 LED UV Curing System for applications at 385 nm. Included: CS2020 con-
trol unit; respective Handheld LED light source CS20H3 with safety shield
and goggles; power supply.
CS20K4 LED UV Curing System for applications at 395 nm. Included: CS2020 con-
trol unit; respective Handheld LED light source CS20H4 with safety shield
and goggles; power supply.
CS20K5 LED UV Curing System for applications at 405 nm. Included: CS2020 con-
trol unit; respective Handheld LED light source CS20H5 with safety shield
and goggles; power supply.
CS2020 LED UV Spot Curing System, Main Control Unit
Accessories:
CAB-CS20 Adapter Cable for Mounted LEDs
CS20A1 Foot Switch for CS2020 Driver with 2.0 m Connection Cable with 3.5 mm
Jack Plug
CS20A2 Collimation Adapter for CS2020 (included with Handheld LED light source)
CS20A3 Focusing Adapter for CS2020 (optional)
CS20Hx Handheld Light Source with LED for Defined Wavelength. To Purchase In-
dividual Handheld Units CS20Hx, please Contact Thorlabs.
22
© 2020 Thorlabs
1 General Information
2
Spare parts:
Power Supply ETC36-24 (24V DC 1.5A)
Stand for CS2020 Handheld LED Light Source
UV Protection Shield
Safety Glasses
For purchasing the above spare parts, please contact Thorlabs.
1.2 Requirements
These are the requirements to the PC intended to be used for remote operation of the CS20Kx.
1.2.1 Hardware Requirements
CPU: 1 GHz or higher
RAM: 1 GB
Graphic card with at least 32 MB memory
Hard disc with at least 100 MB free storage space
Free USB 2.0 port
USB cable according the USB 2.0 specifications
1.2.2 Software Requirements
The CS2010 software package is used for operation of the former product CS2010, CS20Kx
and the driver CS2020 and is compatible with the following operating systems:
·Windows®XP (32-bit) SP3
·Windows®Vista (32-bit, 64-bit)
·Windows®7 (32-bit, 64-bit)
·Windows®8.1 (32-bit, 64-bit)
·Windows®10 (32-bit, 64-bit)
For operation of the CS20Kx with the CS2010 software, NI-VISA™ (version 5.0.2 or higher) is
required. The NI-VISA™ engine comes with the Thorlabs CS2010 software available for down-
load from the CS20Kx software tab, or can be downloaded also from National Instruments'
website www.ni.com.
© 2020 Thorlabs3
CS20Kx
2 Getting Started
2.1 Parts List
Please inspect the shipping container for damage. Do not cut through the cardboard. You might
need the box for storage or returns.
If the shipping container seems to be damaged, keep it until you have inspected the contents
mechanically and electrically.
Verify that you have received the following items within the package:
1. CS2020 Driver for CS20Kx
2. Wide Range Power Supply (24V DC 1.5A) and Power Cord
3. CS20Hx Handheld Light Source with CS20A2 Collimation Adapter and Holder
4. USB 2.0 Cable
5. Safety Glasses
6. Quick Reference CS20Kx
© 2020 Thorlabs
3 Operating Instructions
4
3 Operating Instructions
The CS20Kx can be operated via the display on the CS2020 or remotely, using the software
CS2010. The chapter Display Operation describes operation via the device display, the
chapter Computer Interface gives instructions for remote operation.
3.1 Operating Elements
1
LC Display with Background Illumination
2
Rotary Knob
3
ESC Button
4
OK Button
5
LED ON/OFF Button, Illuminated when LED is On
6
Sliding Lid to Protect the Input Aperture (7)
7
Input Aperture for Irradiance Measurement
8
Ventilation Outlet
9
Handheld Light Source with Rotating LED Head
10
Collimated UV LED Output - Warning
11
UV Protection Shield
12
LED ON/OFF Switch on Handheld Light Source
13
Holder for Handheld Unit
Warning Do NOT look into the output aperture! Do NOT direct the UV emission onto
skin, reflective surfaces or other people.
6
10
© 2020 Thorlabs5
CS20Kx
Rear Panel:
1
Power Switch
2
LED Output (Connector for Hand Set)
3
3.5 mm Jack for Foot Switch
4
USB 2.0 Connector (Remote Computer)
5
DC Input
6
Serial Number
3.2 Basic Setup
Note
Do not cover the air ventilation and avoid overheating of the driver. Please pay attention to the
safety recommendations and the Occupational Health and Safety Regulations applying to your
workplace.
To setup the CS20Kx, install the CS2010 software package and driver package to your PC
prior to connecting the CS2020 to the PC. The software and driver package are available from
the CS20Kx software tab.
·Connect the handheld light source to the driver (jack “LED” (2) on the rear panel).
·Connect the power supply to mains outlet, using the supplied power cord.
·Connect the DC output of the power supply to the jack “24VDC 1.5A” (5) at the rear
panel.
·Switch on the driver using the switch (1) at the rear panel.
·Connect the driver to the control PC using the USB2.0 cable.
5
5
5
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels THORLABS Instrument de mesure
THORLABS
THORLABS PM100D Manuel d'installation
THORLABS
THORLABS SA200 Series Manuel utilisateur
THORLABS
THORLABS Redstone OSA305 Manuel utilisateur
THORLABS
THORLABS INTUN Series Manuel utilisateur
THORLABS
THORLABS HRS015 Manuel utilisateur
THORLABS
THORLABS TPZ001 Manuel utilisateur
THORLABS
THORLABS HRP350 Manuel utilisateur
THORLABS
THORLABS TSP01 Manuel utilisateur
THORLABS
THORLABS PM200 Manuel utilisateur
THORLABS
THORLABS SA200 Series Manuel utilisateur
THORLABS
THORLABS LTS150 Manuel utilisateur
THORLABS
THORLABS LFE1220W-US Manuel utilisateur
THORLABS
THORLABS PM30-120 Manuel utilisateur
THORLABS
THORLABS PM100USB Manuel utilisateur
THORLABS
THORLABS CCS Series Manuel d'instructions
THORLABS
THORLABS M2MS Manuel utilisateur
THORLABS
THORLABS PDA20H Manuel utilisateur
THORLABS
THORLABS K10CR1 Manuel utilisateur
THORLABS
THORLABS VEGA Series Manuel utilisateur
THORLABS
THORLABS GVS001 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur