THORLABS DCC Series Manuel utilisateur
Thorlabs Digital Camera
Quick Start Guide
Table of Contents
Description........................................................................1
1.1. Introduction..................................................................1
1.2. Receiving and Unpacking ..............................................1
Safety.................................................................................2
2.1. Precautions...................................................................2
2.2. Before installation ........................................................2
Setup & installation..........................................................3
3.1. Know Your Camera Family! ...........................................3
3.2. USB Camera Installation................................................4
3.3. GigE Camera Installation:..............................................4
3.4. Camera Link Installation:...............................................4
3.5. Scientific USB 3.0 Installation: .......................................5
3.6. Installing the Software..................................................5
3.6.1. Load the Distribution Disk......................................................... 5
3.6.2. Driver Selection ........................................................................ 6
3.7. Basic Connections .......................................................10
3.7.1. Connections for Camera Link Scientific Camera ......................10
3.7.2. Connections for a Gigabit Ethernet Scientific Camera..............11
3.7.3. Connections for a USB 3.0 Scientific Camera..........................12
Regulatory.......................................................................13
4.1. Waste Treatment is Your Own Responsibility...............13
4.2. Ecological Background ................................................13
Product Care...................................................................14
5.1.1. Service.....................................................................................14
5.1.2. Warranty..................................................................................14
5.1.3. Troubleshooting.......................................................................15
Thorlabs Worldwide Contacts.......................................17
Chapter 1: Description
Page 1
Description
1.1. Introduction
This booklet is a Quick Start Guide to the installation of Thorlabs Compact and
Scientific-Grade cameras, and it is meant to be a companion to the camera user
guides in the Program Files\Thorlabs\Scientific Imaging\Documentation folder
that will be installed with your software. This Quick Start Guide is intended to
provide basic information regarding the initial set-up and installation of your
camera.
It is highly recommended that you familiarize yourself with the detailed
information contained in the documentation folder associated with your specific
camera model and Thorlabs Software once you have completed this installation.
1500_Series_Digital_Camera_User_Guide
Scientific_Series_Digital_Camera_User_Guide
Compact_Scientific_Series_Digital_Camera_User_Guide
TSI_Application_Programming_Interface_Guide
ThorCam_Software_User_Guide
DCx_User_and_SDK_Manual
1.2. Receiving and Unpacking
Your camera was thoroughly tested and carefully packed at the factory. Once the
camera shipment is accepted for delivery, the carrier assumes full responsibility
for its safe arrival. Should you receive your shipment with any damage—
concealed or apparent—please contact the carrier at once. The carrier will
instruct you on how to initiate a damage claim. If a visual inspection reveals
damage upon receipt, it must be noted on the freight bill or express receipt and
the notation signed by the carrier’s agent. Failure to do so can result in the carrier
refusing to honor the claim.
To return your camera to TSI for service, you must first contact your local
Thorlabs office or distributor and request a Return Material Authorization (RMA).
Returns will not be accepted without an RMA. See chapter titled “Warranty
Information” for details.
Chapter 2: Safety
Page 2 ITN000081-D03 Rev. N
Safety
2.1. Precautions
ATTENTION USERS
This attention symbol indicates that additional information is available
in these user guides.
Please read the instruction manual for the appropriate model device carefully
before operating your Digital Video Camera. All statements regarding safety
and technical specifications are published in that document and will only
apply when the unit is operated correctly.
Refer to this Quick Start Guide or User Guide whenever the following symbols
are encountered on the Digital Video Camera and Power Supply:
This equipment is intended for laboratory use only and is not certified for
medical applications, including but not limited to, life support situations.
Check the supply voltage of the system BEFORE plugging in the
power supply. Make sure the included power cord is the correct type for the
service you are connecting to AND connected to a properly grounded power
outlet (100 –240 VAC; 50 –60 Hz).
Transportation and delivery may cause the Digital Video Camera to be warm
or cool upon receipt. Please wait for the device to reach room temperature
before attempting to operate.
There are NO user accessible fuses in this Digital Video Camera or the
included External Power Supply.
Do not open the Digital Video Camera or the External Power Supply.
Doing so is dangerous and could result in damage to the unit or death to the
user.
and a member of our team will be happy to assist you with any questions you
may have regarding this product.
2.2. Before installation
Before proceeding with the installation of hardware or software,
please identify whether your camera interface is Camera Link,
Gigabit Ethernet (GigE), or USB 3.0. Please note the significant
difference in installation steps for the three types of cameras.
Chapter 3: Setup & installation
Page 3
Setup & installation
3.1. Know Your Camera Family!
Scientific Cameras and Compact Scientific Cameras have a black and red
aluminum case. Both Scientific Camera families have their own drivers (Camera
Link, Gigabit Ethernet, USB 3.0) and SDK.
Figure 1 Scientific and Compact Scientific Cameras
DCC- or DCU- (also referred to as DCx) Compact USB Cameras are small
with either a black/stainless steel or grey plastic case, depending on the model.
The DCx Camera family has its own USB drivers and SDK.
Figure 2 DCU/DCC cameras
Chapter 3: Setup & installation
Page 4 ITN000081-D03 Rev. N
3.2. USB Camera Installation
If you purchased a DCx or Compact Scientific USB camera, the only connection
required is with the supplied USB cable.
1. Run the software installer –follow the steps outlined in the next
section, including driver installation.
2. Connect the USB cable* to the appropriate USB port.
3. Wait for windows to recognize the camera
4. Run ThorCam application software
* We recommend using only the USB3 cable that was shipped with the camera.
3.3. GigE Camera Installation:
If you purchased a Gigabit Ethernet camera, an Intel PCI/PCIe adapter card is
provided for use on desktop computer systems. Although the system will work
with other adapters (including laptop GigE adapters), it is recommended that this
card be used for optimal performance on all desktop installations.
1. Power down the computer.
2. Taking necessary precautions, install the Intel PCI/PCIe GigE
adapter.
3. Turn on the computer and accept Windows driver recommendations for
the newly installed hardware
4. Run the software installer –follow the steps outlined in the next
section, including driver installation.
5. Connect camera per section 3.5, then power on camera and run
ThorCam application software.
3.4. Camera Link Installation:
If you purchased a Camera Link camera, an EDT PCIe interface card is provided.
Other Camera Link interface cards are not supported.
1. Run the Software Installer - follow the steps outlined in the next
section, including driver installation.
2. Power down the computer.
Chapter 3: Setup & installation
Page 5
3. Taking necessary precautions, install the EDT PCI/PCIe Camera Link
interface card.
4. Turn on the computer
5. Accept the driver installation recommendations for the newly installed
hardware.
6. Connect camera per section 3.7, then power on camera and run
ThorCam application software
3.5. Scientific USB 3.0 Installation:
If you purchased a Scientific or Compact Scientific USB 3.0 camera, an optional
USB 3.0 PCIe interface card is available, USB3-PCIE, which may provide higher
throughput over an integrated USB 3.0 port on your PC. (Other USB interface
cards may work, but are not supported)
1. Run the Software Installer - follow the steps outlined in the next
section, including driver installation.
2. If installing a PCIe USB3.0 card - Power down the computer. Taking
necessary precautions, install the USB 3.0 PCIe interface card. Turn on
the computer.
3. Otherwise, simply connect the camera to a USB3.0 port on the PC.
4. Accept the driver installation recommendations for the newly installed
hardware.
5. Power on the camera and run the ThorCam application software.
3.6. Installing the Software
The Thorlabs camera software runs on Windows 7, 8.1, and 10 operating
systems ONLY.
3.6.1. Load the Distribution Disk
A CD or DVD disk can be found with the camera. Load the disk into the CD/DVD
drive on the computer you wish to operate the camera and software. The
installation software will automatically detect whether your system is 32-bit or 64-
bit. Loading and detection could take a minute or two, depending on your drive
speed. You may also download the latest version from our website at
https://www.thorlabs.com/software_pages/viewsoftwarepage.cfm?code=
ThorCam .
Chapter 3: Setup & installation
Page 6 ITN000081-D03 Rev. N
3.6.2. Driver Selection
Your camera requires a driver to be installed on your computer. After the
welcome screen, acceptance of the license agreement, and entering your user
information, you will be presented with a choice of drivers. Select the driver that
matches the interface on your camera; USB (2.0 or 3.0), Gigabit Ethernet, or
Camera Link. If you have more than one camera and with different interfaces,
select all that apply. If you’re unsure, select them all.
Select a driver for installation by clicking on the dropdown and selecting either of
the two choices; “This feature will be installed on local hard drive,” or “This
feature, and all subfeatures, will be installed on local hard drive.” There are no
subfeatures, so both choices do the same thing.
If you do not wish to install the driver, select “This feature will not be available”
Once a driver is selected, the red X will be replaced with a hard drive icon as
shown in the USB selection below.
Chapter 3: Setup & installation
Page 7
Click Next to proceed with the driver installation. Depending on your PC’s
configuration and the drivers you selected, you might encounter the additional
Windows security dialogs below. Be sure to click install to complete the
operation, otherwise the installer will “roll back” and exit.
Chapter 3: Setup & installation
Page 8 ITN000081-D03 Rev. N
Camera Link Driver Installation (if selected). Click “Install”
USB Driver Installation (if selected). Click “Install”
Gigabit Ethernet Driver Installation (if selected). Click “Install”
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels THORLABS Appareil photo numérique
THORLABS
THORLABS CC215MU Manuel utilisateur
THORLABS
THORLABS 1500M Series Manuel utilisateur
THORLABS
THORLABS CC505MU Manuel utilisateur
THORLABS
THORLABS 8051 Manuel utilisateur
THORLABS
THORLABS LP126MU Manuel utilisateur
THORLABS
THORLABS DCC3260M Manuel utilisateur
THORLABS
THORLABS CS165 Series Manuel utilisateur
THORLABS
THORLABS LabView DCU2 Series Manuel du propriétaire
THORLABS
THORLABS DCU22 Series Manuel utilisateur
THORLABS
THORLABS S805 Manuel utilisateur
