Thomas&Betts ERG2001 Manuel utilisateur

Figure 1

1.1 1.2

1.3

*See Gaging Table

on Page 2

IMPORTANT: Read and understand all of the instructions and safety information in this manual

before operating or servicing this tool.

COMFORT CRIMP®

ERG2001/ERG2003/ERG2007/ERG1255/ERG2006

SHURE STAKE®TOOL

CALIBRATION VERIFICATION

TA01224 C Page 1 of 2

WARNING

HANDLES ARE NON-INSULATING.

DO NOT CRIMP ON HOT ENERGIZED WIRES.

1.0 INSTRUCTIONS FOR USE

SHURE STAKE®Mechanism

In the event the SHURE STAKE®MECHANISM must be released, please see Figure 2.

Figure 2

WARNING

KEEP ALL BODY PARTS AWAY FROM DIE

NEST DURING GAGING OR CRIMPING

PROCEDURE.

Maintenance

1. Remove dust, moisture, and other contaminants with

a clean brush or a soft, lint-free cloth.

2. DO NOT use on objects that could damage the tool.

3. Make certain all pins, pivot points, and bearing

surfaces are protected with a THIN coat of any good

SAE No. 20 motor oil. DO NOT oil excessively.

4. Keep handles closed when not in use to prevent

objects from becoming lodged in the crimping dies.

5. Store tool in a cool, dry area.

SHURE STAKE

Mechanism Check

1. Squeeze handles until jaws are fully closed but before

SHURE STAKE®mechanism releases.

2. Apply a force gradually at 1-1/2” from end of handles

until SHURE STAKE®mechanism relases, see Figure 2.

3. The force required to release the SHURE STAKE®

mechanism should be 35 lbs minimum, 45 lbs.

maximum.

1-1/2

To release the SHURE STAKE®

mechanism, push up on the

release bar until the ratchet

teeth are disengaged.

WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product

for the user’s intended application. Thomas & Betts warrants that this product will be free from defects in materials and workmanship for the period stated

on the enclosed warranty card. Upon prompt notiﬁcation of any warranted defect, Thomas & Betts will, at its option, repair or replace the defective product or

refund the purchase price. Proof of purchase is required. Misuse or unauthorized modiﬁcation of the product voids all warranties.

Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER

WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO COST OF

REPAIR OR REPLACEMENT OF THE PRODUCT, AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Thomas & Betts Corporation

Memphis, Tennessee

www.tnb.com

For parts, service, repair and

calibration, contact the Thomas & Betts

Tool Service Center at 1-800-284-TOOL (8665).

2.0 GAGING VERIFICATION

2.1

Tool must be free of cracks, sharp edges and any other

obvious imperfections that may affect performance

of the tool. Nest area must be free of burrs, dents or

scratches.

Visual Inspection 2.2

1. Wipe die nest before gaging.

2. Swing locator away from nests. (Gages are to be

inserted on this side.)

3. Close handles until SHURE STAKE®mechanism just

trips.

4. Using gage pins, insure that each nest meets the

gaging requirements as speciﬁed, see gaging

requirements table.

Gaging Procedure

NOTE: Calibration veriﬁcation procedure should be performed whenever damage or suspected damage

has occurred or as often as operation conditions warrant.

ERG 2001/2003 GAGING

REQUIREMENTS

NEST GAGING

MIN. - MAX.

Wire Size

AWG

RED .100 - .103 #22 - #18

BLUE .117 - .120 #16 - #14

YELLOW .149 - .152 #12 - #10

ERG 2006 GAGING

REQUIREMENTS

NEST GAGING

MIN. - MAX.

Wire Size

AWG

RA .078 - .082 #22 - #18

RB .098 - .102 #16 - #14

RZ .063 - .073 #26 - #22

ERG 1255 GAGING

REQUIREMENTS

NEST GAGING

MIN. - MAX.

Wire Size

AWG

RED .090 - .094 #22 - #18

BLUE .105 - .110 #16 - #14

YELLOW .152 - .158 #12 - #10

ERG 2007 GAGING

REQUIREMENTS

NEST GAGING

MIN. - MAX.

Wire Size

AWG

RED .190 - .196 #8

BLUE .212 - .218 #6

TABLE 1 TABLE 2

TABLE 3 TABLE 4

NOTICE: If tool fails any of the above tests, do not attempt repair or adjustment. Call nearest T&B tool service center to arrange for repair service. Any change,

modiﬁcation or alteration of the tool or use by the customer in a manner other than as speciﬁed by T&B shall void all warranties express or implied and the

customer shall, therefore, assume all liabilty for any damage or injury caused by said changed, modiﬁed or altered tool or improper usage or such tool.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Thomas&Betts Outils de sertissage

Thomas&Betts

Thomas&Betts TBM6 Manuel utilisateur

Thomas&Betts

Thomas&Betts Blackburn Comfort Crimp TBM45S Manuel utilisateur

Thomas&Betts

Thomas&Betts Blackburn TBM62PCR-LI Manuel utilisateur

Thomas&Betts

Thomas&Betts BPLT14BSCRI Manuel utilisateur

Thomas&Betts

Thomas&Betts Stakon Comfort Crimp ERG4255 Manuel utilisateur

Thomas&Betts

Thomas&Betts COLOR-KEYED TBM14RH Manuel utilisateur

Thomas&Betts

Thomas&Betts Blackburn COMFORT CRIMP TBM41E Manuel utilisateur

Thomas&Betts

Thomas&Betts QUICK-KON TNB170-ELECDIE Mode d’emploi

Thomas&Betts

Thomas&Betts BPLT14BSCR Manuel utilisateur

Thomas&Betts

Thomas&Betts BP4UCR Mode d’emploi

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4008 Manuel utilisateur

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4002 Manuel utilisateur

Thomas&Betts

Thomas&Betts STA-KON WT3185 Guide de référence

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4006 Manuel utilisateur

Thomas&Betts

Thomas&Betts Comfort Crimp ERG2002 Manuel utilisateur

Thomas&Betts

Thomas&Betts TBM5 Manuel utilisateur

Thomas&Betts

Thomas&Betts STAKON COMFORT CRIMP ERG4004 Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

Panduit

Panduit CT-1000 Guide de l'administrateur

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur