THine THSEU101 Manuel utilisateur

THSEU101 User Manual

Rev. 1.00

THSEU101 User Manual

Vision System Starter Kit

Table of Contents

V-by-One® HS Vision System Starter Kit overview ......................................................................................................................... 2

Video path overview ............................................................................................................................................................................ 3

Configuration, control, and status options overview ............................................................................................................... 5

Kit contents............................................................................................................................................................................................. 6

Out of the box setup and operation ............................................................................................................................................... 7

Reference and support ....................................................................................................................................................................... 8

Camera board ............................................................................................................................................................................................. 9

Features ................................................................................................................................................................................................. 10

Connector boards .................................................................................................................................................................................... 14

Overview ............................................................................................................................................................................................... 14

SMA ......................................................................................................................................................................................................... 15

FAKRA ..................................................................................................................................................................................................... 16

Image Output board ............................................................................................................................................................................... 17

Host software application .................................................................................................................................................................... 23

Appendix A: Scripting syntax ............................................................................................................................................................... 27

Appendix B: 2-WIRE devices and addressing ................................................................................................................................. 29

Appendix C: Cypress CX3 firmware update procedure ............................................................................................................... 30

First time programming procedure .............................................................................................................................................. 30

Firmware upgrade from V-by-One® HS based Image Evaluation System application ................................................. 33

Revision History

.............................................................................................................................................................................................. 35

Important Notice

............................................................................................................................................................................................ 36

THSEU101 User Manual

Rev. 1.00

V-by-One® HS Vision System Starter Kit overview

The THine Evaluation System for Industrial and Automotive (V-by-One® HS based Image Evaluation System) USB starter

kit allows designers to evaluate features of the THCV241A, SerDes transmitter with bi-directional transceiver, for vision

solutions working in pair with THCV242A, SerDes receiver with bi-directional transceiver, to increase the distance

between an image sensor and a video processing system up to 15 meters using V-by-One® HS. The V-by-One® HS Vision

System Starter Kit allows evaluating a number of cable and connector types, such as FAKRA and SMA. The goal of the

V-by-One® HS Vision System Starter Kit is to allow maximum flexibility for evaluating THCV241A and THCV242A, and

serving as a design aid.

This User’s Guide will help in understanding the boards’ functions and how to use them. The QUICK START GUIDE

provides instructions for the out-of-the-box setup and demonstration. With the out-of-the-box demonstration, user will

be able to confirm the hardware/software functionality.

V-by-One® HS based Image Evaluation System evaluation kit supports all features of the THCV241A and THCV242A, and

is designed to provide maximum flexibility in terms of options and video path configurations.

The diagram below shows a high level architecture of the V-by-One® HS Vision System Starter Kit.

THSEU101 User Manual

Rev. 1.00

The full kit consists of seven boards and a camera module. The following table provides high level description of these

boards.

Board name

Description

Camera

board

Designed for maximum flexibility for THCV241A via toggle switches, LEDs, and test points.

May be powered from either board-to-board high speed connector or an external power supply.

Connector

boards

These boards are responsible for adopting the generic board-to-board interface of the Camera board

and Image Output board to a specific cable interface. This includes circuitry for power over V-by-One®

HS and Sub-Link overlay.

Connector boards are designed to work in pairs, with each pair featuring a specific connector type.

Image

Output

Board

Designed for maximum flexibility for THCV242A via toggle switches, LEDs, and test points. The Image

Output Board allows for receiving video via THCV242A or inputting video from a camera directly via a

dedicated connector. The Image Output board allows for outputting video to a host PC via USB3.0

interface or to an external MIPI CSI-2 receiver.

Video path overview

The following simplified block diagram shows V-by-One® HS Vision System Starter Kit video path:

FAKRA

SMA

Conn. board

Board-to-

Board

Generic HS

connector

Specific HS

Connectors

Conn. board

Board-to-

Board

Generic HS

connector

Specific HS

Connectors

Camera board

Generic camera

connecter THCV241A

Board-to-

Board

Generic HS

connector

PWR

USB

conn Power

solution

LEDs, stake pins

and toggle

switches

MIPI

I2C

Image output board

Board-to-

Board

Generic HS

connector

THCV242

LEDs, stake pins

and toggle

switches

LEDs, stake pins

and toggle

switches

Generic camera

connecter

CX3 USB

bridge

Power

solution

PWR

USB

conn

Generic AP host

connecter

1:2

2:1

USB

3.0

conn

MIPI

GPIO

I2C

THSEU101 User Manual

Rev. 1.00

Far-End camera to USB host

Note: The "no cable" option is NOT supported.

Far-End camera to external processor

Note: the "no cable" option is NOT supported

Near-End camera to USB host

Camera board

Generic

camera

connecter

THCV241A

B2B HS

conn.

Conn. board (far end)

B2B HS

conn.

Signal cond

and overlay

Cable conn.

Conn. board (near end)

B2B HS

conn.

Signal cond

and overlay

Cable conn.

Image output board

THCV242

Generic camera

connecter

CX3 USB

bridge

Generic AP host

connecter

1:2

2:1

USB

3.0

conn

B2B HS

conn.

3rd party

graphics

processor

THSEU101 User Manual

Rev. 1.00

Configuration, control, and status options overview

V-by-One® HS Vision System Starter Kit is designed to be flexible and allows for various configuration and control

options:

 Full control of all options built into the THCV241A and THCV242A via discrete pins and 2-WIRE interface are

supported. Discrete pins are controlled via onboard switches. 2-WIRE communication is implemented via V-by-

One® HS Sub-Link.

 Multiple video path configurations as shown in section below.

V-by-One® HS Vision System Starter Kit also allows to observe current system state, configuration, and signal quality

via:

 Onboard LEDs

 Test points provided on all key signals throughout the entire video path

 2-WIRE based I/O expanders monitoring control and status signals throughout the entire design and making it

available to the host application

THSEU101 User Manual

Rev. 1.00

Kit contents

V-by-One® HS Vision System Starter Kit includes:

 Camera module

 Camera board

 Image Output Board

 One pair of connector boards for each of the following connector types: FAKRA and SMA

 Eight 1.2 meter SMA cable

 One USB 3.0 cable

 Quick Start Guide

THSEU101 User Manual

Rev. 1.00

Out of the box setup and operation

1. Connect Image Output Board to FAKRA Near End Board.

2. Connect FAKRA Far End Board to Camera Board to the camera.

3. Connect the 10m FAKRA cable From the Far-End board to RX0 (J300) of the Near-End Board..

4. Configure DIP switches on Camera Board and Image Output Board as shown on the diagram

5. Connect the USB3.0 cable from the Image Output Board to a Host PC. In Windows Device Manager this device will

appear under a list of Imaging Devices as THEIA

6. If not already installed, install the latest version of Microsoft Visual C++ 2015 Redistributable.

7. Obtain VSSK PC Software Suite from THine Solutions.

8. Extract package contents into a directory the application will run from and launch the host application.

In host application, under Devices menu select the THEIA camera.

Observe video from the camera in Vby1Viewer application window

THSEU101 User Manual

Rev. 1.00

Reference and support

V-by-One® HS Vision System Starter Kit design data, programming files, and other support data can be found at

https://www.thinesolutions.com/vision-system-starter-kit

THSEU101 User Manual

Rev. 1.00

Camera board

The Camera board hosts the THCV241A bi-directional transceiver receiving MIPI CSI-2 data from an image sensor.

Camera configuration is controlled via 2-WIRE interface supported by the CML Sub-Link. Camera board also contains a

complete clocking and power solutions. Test points and status indicators are available on the board for all key signals.

Camera board may be powered independently by a standard 5V power supply or from the Image Output board through

connector boards.

THSEU101 User Manual

Rev. 1.00

Features

Generic camera connector

V-by-One® HS Vision System Starter Kit utilizes camera adapter boards for interfacing to specific camera modules. V-by-

One® HS Vision System Starter Kit is supplied with VSSK Camera. The generic camera connector is implemented with

Samtec QTH-030-02-L-D-A. Refer to schematics for pinout and other details.

THCV241A-B bi-directional transceiver

THCV241A is designed to support 1080p60 2Mpixel uncompressed video data over 15m 100 Ohm differential STP or

single-end 50 Ohm Coaxial cable with 4 in-line connectors between camera and processor via V-by-One® HS.

THCV241A supports a MIPI CSI-2. Each CSI-2 data lane can transmit up to 1.2Gbps/lane. Virtual channel is supported.

One high-speed V-by-One® HS lane can transmit up to 1080p60fps. The maximum serial data rate is 4Gbps/lane. 2nd

output lane supports HDR large amount of data or data copy-and-distribution experience.

Power solution

The camera board can be powered from an external source or from the board-to-board connector. Powering from the

board-to-board connector requires the use of a connector board that supports power over V-by-One® HS or proper cable

connection in the case of the SMA connector board. When powering the camera board externally via the optional

auxiliary power input, connect a 5V adapter via the micro USB connector.

When power is applied to the board from either external adapter or from the board-to-board connector, the LED, D902,

labeled Power Good will be illuminated. When power is present from the board-to-board connector, the LED, D907,

labeled POC (Power-Over-Cable) will also be illuminated.

Autres manuels pour THSEU101

Table des matières

Autres manuels THine Système de vision industrielle

THine

THine THSEU101 Manuel utilisateur

THine

THine THEVA12LVDR820 Manuel utilisateur

Manuels Système de vision industrielle populaires d'autres marques

Festo

Festo SBOC-M-R1B-H Manuel utilisateur

Banner

Banner VE200G1B Manuel utilisateur

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manuel utilisateur

Sony

Sony Vision Exchange PEQ-C100 Manuel utilisateur

Datalogic

Datalogic MX-U81 Instructions d'installation

Cognex

Cognex In-Sight D900 Series Manuel utilisateur

Spektrum

Spektrum SPMVR2520 Manuel utilisateur

Huaray

Huaray Movidius Series Manuel utilisateur

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Manuel utilisateur

SVS-Vistek

SVS-Vistek exo174 U3 Series Manuel utilisateur

Teledyne

Teledyne e2v Eliixa+ Series Manuel utilisateur

Photron

Photron FASTCAM Mini CX Series Manuel utilisateur

National Instruments

National Instruments Vision CVS-1455 Manuel utilisateur

Omron

Omron FH-L550 Manuel utilisateur

iGen

iGen NV20/20 Manuel utilisateur

JAI

JAI GO-5100MP-USB Manuel utilisateur

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Manuel utilisateur

Cognex

Cognex In-Sight 9902L Manuel utilisateur